Sony MV-7101DS Installation/Connections

Parts for the overhead monitor XVM-R70

1

Pièces nécessaires au moniteur suspendu XVM-R70

Componentes del monitor suspendido XVM-R70

2

1

3

5 m (16.4 ft)

5 m (16.4 ft)

5 m (16,4 pi)

5 m (16,4 pi)

5 m

5 m

4

Parts for the player MV-101

Pièces nécessaires au lecteur MV-101

Componentes del reproductor MV-101

5

6

7

8

2 m (6.6 ft)

× 4

× 2

× 4

2 m (6,6 pi)

2 m

— It will obstruct the operation of the vehicle,

especially the steering wheel, shift lever, or

Parts list (1)

brake pedal.

The numbers in the list are keyed to those in the

— A driver or passengers may injure themselves

instructions.

when getting into or out of the car.

If you have any questions or problems

concerning your unit that are not covered in this

Cautions on installation of the

manual, please consult your nearest Sony

monitor XVM-R70

dealer.

• Installing the monitor

requires technical

How to set the power select

expertise.

The monitor should be

switch on the monitor XVM-R70

installed by a qualified

(3)

technician or service

personnel.

Before installing

• If you try to install the

Make sure that the POWER SELECT switch is set to

monitor by yourself, do

the correct position.

it properly, referring to

A*: if your car has ACC (accessory) position on the

the installation and

ignition key switch.

connection diagrams in

B : if your car has no ACC (accessory) position on

this installation/

the ignition key switch.

connection manual.

Improper installation

* A is the factory preset position.

may result in fire or

x

electric shock.

• Before installation, be

Warning when installing in a car

sure to turn the ignition

without ACC (accessory)

key switch to the OFF

position or take the key

position on the ignition key

out. Installing the

monitor with the

switch

ignition key switch ON

may cause battery drain

To turn on the player and the monitor,

or a short circuit.

after you set the power select switch to B

• Do not damage any

(the setting without ACC position) for your

pipes, tubes, the fuel

car

tank or electric wiring

Press (POWER) on the monitor*.

when installing the

monitor. This can cause

* You cannot turn on the player and the monitor by

a fire. If you drill a hole

pressing (POWER) or (MONITOR POWER) on the card

in car panels, make sure

remote commander.

that any hidden car

To turn off the player and the monitor,

parts will not be

after you set the power select switch to B

damaged.

• Do not use any nuts or

(the setting without ACC position) for your

bolts for safety devices

car

such as steering linkage,

There are 3 ways to turn off the player and the

fuel supply or braking

monitor:

systems. This can cause

— After turning off the ignition, be sure to press

a fire or an accident.

(POWER) on the monitor.

• Take care to prevent

— After turning off the ignition,

cords and wires from

(MONITOR POWER) on the card remote

getting tangled or

commander

crimped in the moving

— After turning off the ignition, just close the

portion of a seat rail.

display panel of the monitor until it clicks.

XVM-R70 (2)

Caution

Installing the monitor requires technical

expertise. The monitor should be installed by

a qualified technician or service personnel.

Where to install

Before installing the monitor, please check your

local traffic rules and regulations. Follow the

diagram below to install the monitor in a suitable

position in your car.

Do not install the monitor where:

— It will obstruct the driver’s view when the

monitor is in either the open or closed position.

— It will obstruct the operation of the airbag

system.