Emerson SR400, SR401 - Remote Control Manual

Features

Model Number SR400

• 4-Speed Hand Held Transmitter
• Single Light
• Supplied with Receiver
• Includes Light Dimming Selection Switch

Model Number SR401

• 4-Speed Hand Held Transmitter
• Single Light
• Use with SR400 or SW405
• Includes Light Dimming Selection Switch

Read all instructions carefully before installation. Save this Owner's Manual for future reference.

Safety Instructions

To avoid fire, shock, and serious personal injury, follow all instructions carefully.

1. Read your Owner's Manual carefully before installing the remote control. RetainOwner's Manual for future reference.
2. Be careful of the fan and blades when installing the receiver in the ceiling cover. Before installing or servicing the ceiling fan or receiver, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.

ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION

1. To avoid possible electrical shock, be sure electricity is turned off at the main fuse orcircuit breaker box before wiring.
2. Make certain no bare wires are exposed outside the wire connectors.
3. All wiring must conform to National and Local Electrical Codes.
4. Follow the recommended instructions for the proper method of wiring your new remotecontrol. If you feel you do not have enough electrical wiring knowledge or experience, have your remote control installed by a licensed electrician. Any electrical work not described in this manual should be performed by a licensed electrician.

General

Your Emerson Ceiling Fan/Light Remote Control consists of hand-held transmitter and a receiver which is mounted under the fan ceiling cover. The remote control is designed to separately control your ceiling fan speed and light intensity. There are four push buttons (^., ^.., ^..., ^....) to set the fan speed and turn the fan off. The light ( ) push button turns the light on and off and controls the light intensity. The red indicator light will illuminate while any button is pressed, indicating that the battery is good.

The remote control transmitter is powered by two AAA alkaline batteries (not included). To prevent possible damage if the batteries should leak, be sure to remove the batteries when the control is not to be used for an extended period of time.

Code switches in the transmitter may be set in 32 different positions. If your fan and light go on and off without using your control, you may be getting interference from other remote units such as garage door openers, car alarms or security systems. To remedy this situations, simply change the combination code in your transmitter.

Preset Memory Feature

Your Emerson receiver is equipped with a preset memory feature. If the AC supply to the receiver is powered through a wall switch, when the switch is turned OFF, the control will remember the light intensity and fan speed. When the switch is turned back ON the light and fan will resume operation as they were prior to the switch being turned OFF.

Installation of Battery

1. Remove the battery cover by pressing firmly below the arrow and sliding the cover off the control.
   
2. Install two AAA alkaline batteries.

Setting Operating Frequency of Transmitter

Your remote control transmitter has code switches which must be set in one of 32 possible code combinations. The five levers (numbered 1, 2, 3, 4, and 5) on the switches are factory-set in the ON (up) position. Do not use this setting. Change the switch settings as follows:

1. When power is restored after installation of the wall control, push and hold the fan OFF button ( ) for 3 to 5 seconds to set the code in the receiver.

Installation of Receiver

To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before installing the receiver.

1. Connect the black supply wire to the receiver black wire (AC IN L). Connect the white supply wire to the receiver white wire (AC IN N). Use only listed wire connectors (supplied) to make connections.
   
2. Connect the receiver white wire (TO MOTOR N) to the fan white wire. Connect the receiver red wire (TO MOTOR L) to the fan black wire. Connect the receiver blue wire (FOR LIGHT) to the fan blue wire.

If no light exist on your ceiling fan, cap the blue wire on the receiver with a wire connector.

Operation

Fan installation must be completed, including the installation of the fan blades, before testing the remote control.

Your remote control has full control of your fan and light.
NOTE: Prior to operation of the fan and light from the remote control, set the fan speed to HIGH ( ^.... ) and turn the light ON ( ).

1. To set the desired fan speed, press one of the four buttons (^., ^.., ^..., ^....) to operate your fan from low to high speeds.
2. To turn the downlight on, press and release the ( ) button. The light will turn on at the light intensity previously selected.
3. To vary the intensity of the light, hold the ( ) button down until the desired light intensity is reached, then release the button.
   Note: When turning the light on, light will turn on at the light intensity previously selected.

Installation of Storage Bracket

A storage bracket is provided for holding your remote control when not in use. If you desire to use the bracket, install it on a wall that is away from excess heat or humidity.

Trouble Shooting

Fan/Light Fails to Operate

• Check that the speed switch on the fanis set to HIGH (^....) speed.
• Check that the light switch is on.
• Check that the battery is good(power indicator light should light when any button is pressed).
• Check that the receiver is wiredproperly.
• Check that code switches in the remotecontrol and receiver are set in the same position.

Short Range

EMERSON
Air Comfort Products
DIVISION OF EMERSON COMPANY
8100 W. Florissant • St. Louis, MO 63136

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.