Table of Contents
Removing and installing intake grille
Removing intake grille
1. Open the intake grille until it snaps.
2. Pull the mounting shafts while keeping the intake grille in a
horizontal position.
Installing intake grille
1. While holding the intake grille horizontally, set the left and
right mounting shafts into the pillow blocks at the top of the
front panel.
Insert the shaft until it snaps to latch each shaft properly.
2. Close the intake grille.
3. Press 6 places on the intake grille to close it completely.
After extended non-use of the unit
If you have shut down the indoor unit for 1 month or more, perform the
Fan mode operation for half a day to dry the internal parts thoroughly
before the normal operation.
Additional inspection
After a long period of use, accumulated dust inside the indoor unit may
reduce the performance even if you have maintained the unit properly.
In such a case, a product inspection is recommended.
For more information, consult authorized service personnel.
Filter indicator reset (Special setting)
This function can be used if set correctly during installation. Consult
authorized service personnel in order to use this function.
Clean the air fi lter when the indicator lamp shows the
following:
Indicator lamp
Blinks 3 times, at intervals of 21 seconds
After cleaning, reset the fi lter indicator by pushing
unit for 2 seconds or less.
12. GENERAL INFORMATION
Heating performance
This air conditioner operates on the heat-pump principle, absorbing heat
from the air outdoors and transferring that heat to the indoor unit. As a
result, the operating performance is reduced as outdoor air temperature
drops.
If you feel that the heating performance is insuffi cient, we recommend
you to use this air conditioner in conjunction with other kinds of heating
appliances.
Blinking pattern
on the indoor
Automatic defrosting operation
When the outdoor temperature is very low with high humidity, frost
may form on the outdoor unit during the heating operation, and it could
reduce the operating performance of the product.
For frost protection, an automatic defrost function is equipped in this air
conditioner.
If frost forms, the air conditioner will temporarily stop, and defrost circuit
will operate briefl y (maximum of 15 minutes.)
[ ] indicator on the indoor unit blinks during this operation.
If frost forms on the outdoor unit after the Heating operation, the outdoor
unit will stop automatically after it operates for a few minutes. Then the
Automatic defrosting operation starts.
Auto-restart function
In the event of a power interruption such as a blackout, the air
conditioner stops once. But it restarts automatically and performs the
previous operation when the power supply is resumed.
If any power interruption occurs after the timer is set, the counting down
of the timer will be reset.
After the power supply is resumed, [
blinks to notify you that there has been a timer fault. In such a case,
reset the clock and timer settings.
Malfunctions caused by other electrical
devices
Use of other electrical appliances, such as an electric shaver or nearby
use of a wireless radio transmitter, may cause the malfunction of the air
conditioner.
If you encounter such a malfunction, turn off the circuit breaker once.
Then turn it on again, and resume operation by the remote controller.
Indoor unit temperature and humidity range
Permissible ranges of temperature and humidity are as follows:
Cooling/Dry mode
Outdoor temperature
Indoor temperature
Indoor humidity
Heating mode
Outdoor temperature
Indoor temperature
*1) If the air conditioner is used continuously for many hours, water may
condense on the surface and drip.
• If the unit is operated under conditions except for the permissible
temperature range, the air conditioner operation may stop because
of the automatic protection circuit working.
• Depending on the operating conditions, the heat exchanger may
freeze, causing water leakage or other malfunction (in the Cooling
or Dry mode).
Other information
• Do not use the air conditioner for any purpose other than room
cooling/dry, room heating, or fan.
13. OPTIONAL PARTS
13.1. Wired remote controller
The optional wired remote controller can be used.
You can use wired and wireless remote controllers together.
However, some functions of the wireless remote controller are restricted.
If you set the restricted functions, beeps will be heard, and [ ], [
[
] and [
] indicator lamps on the indoor unit will blink.
When using together with wired remote controller (2-wire)
• Weekly timer operation
• Powerful operation
• Outdoor Unit Low Noise operation
• 10°C Heat operation
] indicator on the indoor unit
[°C]
-10 to 46
[°C]
18 to 32
1)
[%]
80 or less*
[°C]
-15 to 24
[°C]
16 to 30
],
En-12
Table of Contents
