Before operating the unit, please read this manual thoroughly. This manual should be retained for future reference.
This product is intended for use in the following
Electromagnetic Environments: E1 (residential), E2 (commercial and light industrial), E3 (urban outdoors), E4 (controlled EMC environment, ex. TV studio).
ATTENTION
The electromagnetic fields at the specific frequencies may influence the sound of this unit.
Wind screen
Microphone holder
Notes:
The output connector of the microphone is the XLR3-12C type. Connect the microphone plug to the microphone input of a mixer or a tape recorder. The microphone cable is 3 m (10 feet) long.
If a longer cable is necessary, an extention cable up to 200 m (660 feet) may be used without affecting sound quality or performance. Use a cable with an XLR-3-11C connector at one end and an appropriate plug at the other end which matches the input equipment.
Note:
If cable connector connection is necessary, note that there are two basic types of connections, balanced to ground and unbalanced to ground, and solder connections carefully. Poor soldering may cause hum pick up.
Type: Electret condenser microphone
Power supply: IEC designation R6 or LR6 battery (size AA)
Microphone output terminal: XLR-3-12C type
Microphone cable: Approx. 2.3 mm dia., 3 m long (3/32 inch dia., 10 feet long)
Dimensions: Microphone: Approx. 8.5 mm dia. ×14.5 mm (11/32 dia. × 19/32 inches)
Power supply section: Approx. 20 mm dia. × 126 mm (13/16 dia. × 5 inches)
Mass: Microphone: Approx. 2 g (0.07 oz)
Power supply section: Approx. 120 g (4.2 oz) (including cable, not including battery)
Supplied accessories:
Storage case (1)
Microphone holder (1)
Wind screen (1)
Operating Instructions (1)
Warranty booklet (1)
Frequency range: 40 Hz–15,000 Hz
Directivity: Omni-directional
Output impedance: 250 ohms ±20% (1 kHz), balanced
Sensitivity (typ.): –53 dB (2.2 mV) (0 dB = 1 V/Pa, 1 kHz)
Signal-to-noise ratio: 62 dB (typ.) (IEC 179 A-weighted, 1 kHz, 1 Pa)
Inherent noise: 32 dB SPL (typ.) (0 dB = 2 × 10–5 Pa)
Wind noise*1: Less than 40 dB SPL (with wind screen)
Maximum input sound pressure level *2: 122 dB SPL (typ.)
Dynamic range: 90 dB (typ.)
Operating temperature: 0°C to 60°C (32°F to 140°F)
Storage temperature: –20°C to +60°C (–4°F to +140°F)
*1 Value derived by applying a wind velocity of 2 m/sec. (6.6 ft./sec.) to the microphone from all directions, and converting the mean value to the equivalent input sound pressure level (0 dB = 2 × 10–5 Pa).
*2 Value derived by taking the input level at which 1% waveform distortion occurs with a 1-kHz microphone output signal, and converting it to the equivalent input sound pressure level (0 dB = 2 × 10–5 Pa).
Normal operating voltage: 1.5 V DC
Minimum operating voltage: Approx. 1.1 V DC
Current drain: Less than 0.2 mA (1.5 V DC)
Battery life: R6 manganese battery: Approx. 5,000 hours
LR6 alkaline battery: Approx. 6,000 hours
Design and specifications subject to change without notice.
Note:
Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY
PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the ECM-44B that isn't answered in the manual? Leave your question here.