Mart TS-42-3 ECO User Manual

E

ON

Fig. 3 .: Diagrams of the operation principles of the TS-42-3 TWILIGHT SWITCH.

V. Repair and maintenance

All repairs of the TWILIGHT SWITCH TS-42-3 are performed by the manufacturer. The device does not

require any maintenance. When the sensor becomes contaminated, clean it with a clean, damp cloth. The

device does not require any additional maintenance.

The manufacturer guarantees the correct operation of the TS-42-3 TWILIGHT SWITCH. The warranty period

is 36 months from the date of sale. The warranty is extended by the time of repair. Warranty repairs are

performed by the manufacturer free of charge after the AUTOMAT is delivered to the manufacturer. Improper

use of the device or independent modifications to it will void the warranty.

................................................................................................................................................................................

www.mart-electronics.eu

The TS-42-3 TWILIGHT SWITCH meets the requirements of the European Union Directives:

- Directive LVD 2014/35/EU - Low Voltage Directive of 26 February 2014

- Directive EMC 2014/30/EU - Eletromagnetic Compatibility Directive of 26 February 2014

In order to protect the environment, do not throw away used electrical appliances

and electronics together with municipal waste. Used equipment should be delivered to

collection points for recycling free of charge. Any information on this can be obtained

at sellers, distributors, manufacturer or on the Internet. The product's packaging is made of

ecological materials. The PVC packaging tape will be used while stocks last.

t

OFF

VI. Warranty Card

Made in Europe

TWILIGHT SWITCH

TS-42-3 ECO

The TWILIGHT SWITCH TS-42-3 is designed to automatically switch the receiver on at the moment

of dusk and turn it off at dawn, or vice versa (NO, NC contacts). Two independent knobs for setting the switch-

on and switch-off thresholds allow for an optimal way to control the lighting. Independent adjustment of the

activation thresholds corrects the location of the sensor (north, south, east, west) and eliminates the hysteresis

that occurs in standard automatic units. Hysteresis causes switching off the lighting in the morning when the

lighting intensity is higher (2 ÷ 3 times) than the set lighting intensity level at which the lighting was turned on.

This causes an unfavourable extension of the lighting operation time in the morning, which results in an

increased consumption of electricity. On the other hand, too little hysteresis means that on cloudy days the

lamp may turn on and off with changing weather conditions, which is not advisable, and sometimes even

unacceptable for some lamps.

The light intensity measurement sensor has a spectrum similar to that of the human eye, and the adjustment

thresholds have logarithmic characteristics - also similar to the characteristics of the human eye.

Such an innovative design of the TS-42-3 TWILIGHT SWITCH makes the lighting control optimal, economic

and ecological.

The TS-42-3 TWILIGHT SWITCH includes:

>> TS-42 CONTROLLER - mounted in a distribution box on a 35 mm rail (one 18 mm module)

>> OUTDOOR SENSOR (IP65) - surface-mounted box mounted to the wall with two screws with a PG9 gland

to insert the cable. Connection cable not longer than 100m.

II. Features of the TWILIGHT SWITCH TS-42-3 ECO

>> Independent regulation of activation and deactivation thresholds

>> precise logarithmic adjustment:

> activation - 1 ... 10 ... 100 lx

> shutdown - 1 ... 10 ... 100 lx

>> high switching power - 16A (4000 W) 250VAC, 16A (384 W) 24VDC

>> high inrush current - resistance to 100 A surge current

>> freedom of connections:

> executive relay contacts (one normally open contact - NO, one normally closed contact - NC) galvanically

separated, which allows connections in various configurations

>> traffic light (LED):

> Green LED - indication of 230V AC supply voltage on LN terminals

> LED red:

- pulsating signalling (without delay) - the set (set) actuation threshold is exceeded

- continuous light - the level of the measured illuminance is between the settings on

knobs

> Blue LED - changeover indication - switching on (contact 1-2), disconnection (contact 2-3)

>> 35mm rail mount - one 18mm module.

The TS-42-3 CONTROLLER uses a specialized OMRON G2RL-1-E-HR relay, designed to switch various

types of lighting lamps. The special design of the relay enables effective switching of lamps with an inrush

current up to 100 A.

MADE IN EUROPE

FIRST

ECO

3-YEAR

WARRANTY

User manual

I. Purpose