When using electrical appliances always follow the safety precautions below.
Using the espresso machine
Installation of the espresso machine
Cleaning the espresso machine
Do not use the appliance if the cord or plug are damaged, if the appliance shows signs of malfunctioning or has been damaged in any way. Take the machine to the nearest authorised service center for checks or repairs.
If the power cord is damaged it must be replaced by the manufacturer or an authorised service center.
In case of damage or malfunction, turn off the appliance and do not tamper with it. For repairs contact a service center authorised by the manufacturer and request the use of original spare parts only. Failure to comply with these instructions may compromise safe operation of the machine and will result in the forfeiture of warranty rights.
SAVE THESE INSTRUCTIONS.
Improper use of the appliance
Before connecting the machine to a power supply, carefully read the safety instructions given in the chapter: "IMPORTANT SAFEGUARDS".
Make sure that the machine is unplugged.
Insert the capsule holder from below and turn it to the right until it locks into place.
Pull the water tank out of the machine and fi ll it with fresh drinking water until the MAX mark is reached.
always fi ll the tank with fresh, still drinking water only. Hot water or other liquids may damage the tank. Do not use the machine without water.
Fit the tank to the machine, making sure it is fully inserted in place. Insert the plug into the outlet. Consult the following chapter to switch on the appliance.
Note: it is advisable to keep the original packaging (at least for the duration of the warranty period) in order to ship the machine to an authorised service center for repair if necessary.
While the machine is operating, contact with the brew head D, the steam wand O or the metal part of the capsule holder may cause burns.
Before switching on the machine check the water level in the tank; if necessary add water as described previously. Empty and rinse out the drip tray every time you fi ll the water tank.
To switch the machine on, press the button until it lights up.
The icons in the circle will light up progressively to indicate the increase in the boiler temperature. After a few minutes, when the machine reaches the operating temperature, the brew button symbol will light up and a brief beep will be emitted. If the triangular symbol lights up and an intermittent beep is emitted, please consult the chapter: "PROBLEMS AND SO- LUTIONS".
Note: When using the machine for the first time or after a long period of disuse, we suggest dispensing a few cups of water without capsule.
To switch the machine off, press the button until the front panel goes off; never disconnect the plug from the power outlet when the machine is switched on.
Stand-by
The machine has been programmed to respect the environment and reduce consumption when it is not being used. When it is not in use, after 30 minutes the machine will switch off automatically. 5 minutes before automatic switch off, the button will flash. If you want to machine to stay on, press the button.
The X7.1 machine is designed to function exclusively with illy "Metodo Iperespresso" capsules.
To make coffee, carry out the following steps:
Note: the capsule should slide easily into place; if this is not the case take it out and reposition it correctly.
Note: coffee will start fl owing out a couple of seconds after you press the button; this is normal for the operation of the machine.
To make other coffees, remove the used capsule and repeat the above steps.
The X7.1 machine allows you to brew the desired quantity of coffee in two modes: automatic and manual.
AUTOMATIC MODE - to set and memorise the quantity of coffee to be brewed, carry out the following steps:
MANUAL MODE - to set the machine to work in the manual mode, carry out the following steps:
Note: in the automatic mode it is also possible to make coffee using the manual procedure.
Note: when the machine is set for MANUAL MODE of the quantity of coffee, after you start brewing it will be necessary to press the coffee button again when the coffee has reached the desired level in the cup in order to stop the flow.
The machine features a steam wand for frothing the amount of milk necessary to prepare one or more cappuccinos.
Prepare one or more cups of coffee following the instructions in the previous section.
Froth the milk as follows:
Press the steam button ; the steam icon in the central circle will light up to signal that the machine is getting ready to dispense steam.
When the machine reaches the right temperature, the button will light up.
At this point the machine will emit a brief beep.
Place a suitable empty container (preferably a metal pitcher) beneath the steam wand and press the button to discharge any residual water; when only steam comes out press the button again.
Note: while steam is being dispensed the button will flash.
Note: For an optimal result: pour 75ml of cold whole milk taken directly from the fridge into a container (preferably a metal pitcher) and keep the steam wand submerged in the milk for a maximum of 25 seconds.
Submerge the steam wand completely into the milk.
Press the button and wait for the milk to froth.
On reaching the desired result, press the button again.
Press the button for a few seconds.
Then press the button again.
Wait a few minutes for the wand to cool down.
Remove the outer part Z and wash it under running water.
Wipe the inside part X clean with a wet cloth.
Note: The two end parts of the steam wand can also be washed in a dishwasher; in this case also remove the inside part from the metal tube. After cleaning, fi t the inside part X all the way onto the steam wand; then fi t the outer part Z.
The steam wand of the machine can also be used to dispense hot water for making tea and infusions.
Check that the coffee button is lit.
Carry out the following steps:
Clean the steam wand of any milk residues.
Place a metal pitcher beneath the steam wand.
Press the steam button for at least 3 seconds.
The machine will start dispensing hot water; the steam button "will flash rapidly.
Press the steam button again on reaching the desired quantity of water.
It is very important to avoid making coffee right after dispensing steam because the water generated by the thermo block is too hot and will impair the fl avor of the coffee.
For this reason the coffee button is disabled when the thermo block temperature is too high.
To switch the machine back to the coffee mode, press the coffee button and wait until the button lights up; during this cooling down phase (approximately 10 minutes), the cup icon in the central circle will flash.
To switch the machine back to the coffee mode quickly (approximately 1 minute), carry out the following steps:
Place a metal pitcher beneath the steam wand.
Keep the steam button pressed down for 3 seconds.
A programmed quantity of hot water will be dispensed; the flow will stop automatically.
The formation of limescale is a natural consequence of using of the machine.
The machine features an automatic program designed to optimise cleaning and remove limescale residues from inside the machine.
Note: use only descaling products intended for coffee machines. Please follow the procedure described below, not the instructions on the label of the descaling product.
If the icon in the central circle flashes (1 flash every two seconds) proceed as follows:
Starting the procedure:
Keep the coffee button and steam button pressed down together for at least 5 seconds.
The and buttons and the icon in the circle will flash simultaneously to signal that the automatic descaling cycle has been selected.
At this point it is necessary to clean the internal water circuit of the machine of any residues of the descaling agent.
That is, the machine must be run through a rinse cycle; carry out the following steps:
The descaling solution must be disposed of in accordance with the applicable laws and regulations.
The machine and its components must be cleaned at least once a week.
Keep the water in the tank fresh; wash the tank and fill it daily with fresh drinking water.
Do not use ethyl alcohol, solvents, abrasive sponges and/or aggressive chemicals.
do not dry the machine and/or it components in a microwave or conventional oven.
To clean the machine, carry out the following steps:
Switch the machine off and disconnect the plug from the power outlet.
Remove the water tank and wash it under running water.
Empty out the capsule holder and wash it under running water.
Note: when you refit the inside and outer end parts of the steam wand, make sure to push them up all the way.
You press the button but it does not light up. | Check the mains electrical connection; check the status of the circuit breakers protecting the home electrical system. | |
The machine does not make coffee. | Carry out the following operations:
| |
You press the button and the machine does not dispense steam. Steam comes out but it does not froth the milk. | Case a) | If the steam icon in the circle is lit, wait until the steam button lights up. |
Case b) | If the steam icon in the circle is not lit, press the steam button and wait until the steam button lights up (machine warming up). | |
Case c) | Possible clogging of the steam wand: switch off the machine; wait for it to cool down (at least an hour); remove any obstructions from the outlet holes of the steam wand. | |
Water leaks out of the brew head during brewing. | Insert a new capsule in the capsule holder and fit it to the brew head; proceed with making coffee. | |
Fast beeps and flashing triangular icon. | Carry out the following operations:
| |
Triangular icon flashing rapidly. | Carry out a descaling cycle. | |
Water leaks from the inside of the machine. | Switch off the machine and unplug it. | |
Water leaks from the tank after you have filled it. | Empty the tank; press on the transparent rubber gasket of the coupling valve inside the tank. | |
Some drops of coffee come out of the capsule during the first seconds of brewing. | Any dripping that occurs during the first seconds of brewing is to be considered normal. |
Note: If the problem persists, contact an authorised service center.
To enjoy a high quality espresso, remember to:
This appliance is intended to be used in household and similar applications such as:
The warranty does not cover damage or malfunctions caused by:
The warranty does not cover the costs of repairing machines that have been handled by non-authorised service centers.
Such costs shall be completely borne by the customer.
It is recommended:
Failure to follow these recommendations may cause damage to the machine body which is not covered by the warranty.
It is advisable to keep the original packaging (at least for the duration of the warranty period) in order to ship the machine to a service center for repair if necessary. Any damage caused by transport without adequate packaging will not be covered by the warranty.
Disposal of end-of-life electric and electronic equipment by private households in the European Union.
The WEEE symbol used on this product means that it must not be disposed of together with other domestic waste and should be collected separately. Consumers have the opportunity to hand in their used appliance to distributors free of charge on a 1:1 basis when they purchase a new product..
For further information about the collection of appliances to be scrapped, please contact the local authority in your town of residence, the local waste disposal service or the retailer where the product was purchased. Consumers are responsible for disposing of end-of-life appliances in accordance with the current provisions of law and non-compliance therewith may be subject to fi nes and criminal sanctions.
The correct disposal of this product will contribute to protecting the environment, natural resources and human health.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the FrancisFrancis X7.1 that isn't answered in the manual? Leave your question here.