Toro Groundsmaster 5900 Series Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Blower
  5. Groundsmaster 5900 Series
  6. Installation instructions manual

Toro Groundsmaster 5900 Series Installation Instructions Manual

Leaf mulching kit
Hide thumbs Also See for Groundsmaster 5900 Series:
1
2
3
4
5
6
7
8

Quick Links

Leaf Mulching Kit
2016 and After Groundsmaster
Model No. 31604
This product contains a chemical or chemicals known to the State of California to
Note: Determine the left and right sides of the machine from the normal operating position.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
Center baffle
Right winglet baffle
Left winglet baffle
Baffle divider plate
Carriage bolt (5/16 x 7/8 inch)
Flange nut (5/16 inch)
Carriage bolt (3/8 x 2-1/2 inches)
Flange nut (3/8 inch)
Wing deck baffle
Baffle divider plate
Carriage bolt (5/16 x 7/8 inch)
Flange nut (5/16 inch)
Wing deck baffle
Left baffle divider plate
Carriage bolt (5/16 x 7/8 inch)
Flange nut (5/16 inch)
Register at www.Toro.com.
®
5900 or 5910 Series Rotary Mower
WARNING
CALIFORNIA
Qty.
–
1
1
1
2
16
16
1
1
1
2
9
9
1
1
8
8
Form No. 3405-881 Rev A
Installation Instructions
Use
Prepare the machine.
Install the center deck baffles.
Install the right wing deck baffle.
Install the left wing deck baffle.
Original Instructions (EN)
All Rights Reserved *3405-881* A
Printed in the USA
loading

Related Manuals for Toro Groundsmaster 5900 Series

Summary of Contents for Toro Groundsmaster 5900 Series

  • Page 1 Wing deck baffle Left baffle divider plate Install the left wing deck baffle. Carriage bolt (5/16 x 7/8 inch) Flange nut (5/16 inch) © 2016—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3405-881* A 8111 Lyndale Avenue South...

  • Page 2: Preparing The Machine

    Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Remove the mower deck covers. 3. Raise the center and both wing decks to the transport position. Note: Use a jack stand to support the center deck. Secure the wing decks with the transport deck lock.
  • Page 3 11. Torque the screw at the front of each outer skid to 9 to 11 N∙m (80 to 100 in-lb). CAUTION The blades are sharp and could cause injury to you or bystanders. Rotate the blades away from the installation area to avoid contact.
  • Page 4 Figure 5 1. Nut (5/16 inch) 3. Carriage bolt (5/16 inch) 2. Existing baffle Figure 7 3. Secure the baffle to the existing baffle using a carriage 1. Nut (5/16 inch) 3. Carriage bolt (3/8 x 2-1/2 bolt (5/16 x 7/8 inch) and nut (5/16 inch) as shown inches) Figure 2.
  • Page 5 8. Tighten the fasteners on the right and left winglet 2. Align the center baffle with the mounting holes in the baffles. mower deck and secure with 5 carriage bolts (5/16 x 7/8 inch) and 5 nuts (5/16 inch) as shown in Figure 9.
  • Page 6 Figure 12 1. Hole in baffle 2. Hole in divider plate Figure 13 4. Tighten the fasteners on the baffle. 1. Bolt 3. Nut 5. Rotate the blades, by hand, to verify that the deck 2. Existing baffle baffles do not interfere with their operation. 2.
  • Page 7 Figure 15 1. Flange nut (5/16 inch) 3. Carriage bolt (5/16 x 7/8 inch) 2. Baffle divider plate 4. Tighten the fasteners on the baffle. 5. Rotate the blades, by hand, to verify that the deck baffles do not interfere with their operation.

This manual is also suitable for:

Groundsmaster 5910 series31604