Atlas Copco POWER FOCUS 6000 Product Instructions
Hide thumbs
Also See for POWER FOCUS 6000:
- Pocket manual (27 pages) ,
- Product instructions (20 pages) ,
- Configuration manual (16 pages)
Table of Contents
Printed Matter No. 9836 6528 01
Publication Date 2020-03-30
Valid from Serial No. A4740001
POWER FOCUS 6000
Read all safety warnings and instructions
Failure to follow the safety warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference
POWER FOCUS 6000
8436180002
WARNING
Control and drive unit
Product Instructions
Table of Contents
Related Manuals for Atlas Copco POWER FOCUS 6000
Summary of Contents for Atlas Copco POWER FOCUS 6000
- Page 1 POWER FOCUS 6000 Printed Matter No. 9836 6528 01 Control and drive unit Publication Date 2020-03-30 Valid from Serial No. A4740001 Product Instructions POWER FOCUS 6000 8436180002 WARNING Read all safety warnings and instructions Failure to follow the safety warnings and instructions may result in electric shock, fire and/or serious injury.
-
Page 2: Table Of Contents
Programming a Pset................ 14 Service ........................ 15 Preventing ESD Problems ................ 15 Maintenance Instructions................ 15 Service Recommendations.............. 15 Replacing the Backup Battery for the Clock and Calendar Func- tion....................... 15 Repair Instructions.................. 15 Wiring .................... 15 Recycling ....................... 17 Environmental Regulations................ 17 © Atlas Copco Industrial Technique AB - 9836 6528 01... - Page 3 Recycling Information .................. 17 © Atlas Copco Industrial Technique AB - 9836 6528 01...
-
Page 4: Product Information
■ Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty. ■ To avoid damage or destruction of tool parts, service the tool according to the recommended mainte- nance schedules and follow the correct instructions. -
Page 5: Website
Technical Product Data can be found on either ServAid, or the Atlas Copco website. Please visit: https://servaid.atlascopco.com or www.atlascopco.com. Line Voltage The POWER FOCUS 6000 operates on a single-phase 115 or 230 VAC line voltage. © Atlas Copco Industrial Technique AB - 9836 6528 01... -
Page 6: Mains Fuse
If you are running the POWER FOCUS 6000 as a stand-alone unit and trigger the tools manually (at ran- dom) it is normally possible to connect up to three POWER FOCUS 6000 units to one power drop. If you are synchronizing the spindles you need one drop for each POWER FOCUS 6000 unit. The fusing in the power drop must be of the time delay type. -
Page 7: Installation
POWER FOCUS 6000 Installation Installation Installation Requirements Installation Checklist The POWER FOCUS 6000 is a control and monitoring unit for electric assembly tools. A working system consists of the following: ■ the POWER FOCUS 6000 ■ an IAM, Intelligent Application Module, containing software, configurations and licenses ■... -
Page 8: Installation Instructions
EN 60204-1:2006, 5.3.2 a), b), c) or d). When intended for such use, the supply disconnecting device shall be colored red and have a yellow background. (Ref. EN 60204-1:2006, 10.7.5). © Atlas Copco Industrial Technique AB - 9836 6528 01... - Page 9 50 meters Pin Configurations for Emergency Stop The POWER FOCUS 6000 has an external EM Stop interface and an I/O bus on the connector board that is located behind the front access door. The pin configuration is different for single controller solutions and for multiple controller solutions. For sin- gle controller solutions, the pin configuration depends on whether or not an EM Stop button is connected to the controller.
- Page 10 Single Controller Without EM Stop Button WARNING Remote start switch must be set to OFF for this configuration The POWER FOCUS 6000 comes with jumpers preinstalled for this configuration. Connector: Phoenix, 10-pin headers, 3.5 mm pitch Use the following pin configuration:...
- Page 11 8 See pin 7 Do not use Do not use Controllers between first and last EM Stop I/O cable connector: Phoenix, 10-pin Remove plug or use the following pin configuration: © Atlas Copco Industrial Technique AB - 9836 6528 01...
-
Page 12: Qst Cable
Resetting an activated emergency stop is done by the software. QST Cable QST spindles can be used in combination with the Power Focus 6000. The QST types approved to be compatible with the Power Focus 6000 are: QST 34/42/50/62. Requirements... -
Page 13: Functional Test Of The Residual-Current Circuit Breaker With Overcurrent Protection (Rcbo) Device
(Extension cables 4220 4393 XX are not recommended). The product number for connecting the Power Focus 6000 to a QST tool, is: 4220 4715 XX For proper handling and installation of QST cables, please also follow the guidelines described in the "Pocket guide to Cable Management"... -
Page 14: Operation
In dusty environments, use a dust extraction system or wear a mouth protection mask. Configuration Instructions Programming a Pset Please refer to the User guide for information on how to program a Pset. © Atlas Copco Industrial Technique AB - 9836 6528 01... -
Page 15: Service
Blue Neutral Green and yellow Protective ground Warning! The power cable is the primary means of disconnection. Before opening a POWER FOCUS 6000, make sure to unplug the power cable. © Atlas Copco Industrial Technique AB - 9836 6528 01... - Page 16 RCBO device, even if the power supply is from an isolated transformer. Warning! If the power cable needs to be replaced, only use a genuine Atlas Copco replacement power ca- ble. Use of a non-genuine power cable may result in dangerous situations.
-
Page 17: Recycling
When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle the components in accordance with local legislation. Batteries shall be taken care of by your national battery recovery organization. Recycling Information Part Recycle as Chassis Aluminum Wall mount Steel © Atlas Copco Industrial Technique AB - 9836 6528 01... - Page 18 Skiip module plate Steel Screw Steel Chassis lid Aluminum Washer Steel Radio cover Front lid Aluminum Lithium battery Battery IT board WEEE Speaker WEEE Front Aluminum Logo plate Aluminum Overlay WEEE © Atlas Copco Industrial Technique AB - 9836 6528 01...
- Page 20 Original instructions © Copyright 2020, Atlas Copco Industrial Technique AB. All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. Atlas Copco Industrial This applies in particular to trademarks, model denominations, part numbers Technique AB and drawings.