Pioneer MVH-MS310BT - Marine Digital Media Receiver Quick Start Guide

(Serial number)
The serial number is located on the bottom of this unit. Be sure to record this number on the enclosed warranty card before the unit is installed.

If your boat's ignition has no ACC position, some settings are not saved to the memory. To save, detach the front panel or wait for the unit to shut off completely for 10 seconds after turning it off by pressing and holding SRC/OFF (when [ON] is selected in [PW SAVE]), then turn the ignition off.

This guide is intended to guide you through the basic functions of this unit. For details, please refer to this product's Operation Manual, which you can look up here: https://www.pioneerelectronics.com/PUSA/Support

See Operation Manual for instructions to turn off demonstration display (DEMO OFF).

Before You Start

To ensure proper use, please read through this guide and the Operation Manual before using this product. It is especially important that you read and observe WARNINGS and CAUTIONS in this guide. Please keep the guide in a safe and accessible place for future reference.

The Safety of Your Ears is in Your Hands

Get the most out of your equipment by playing it at a safe level—a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving.

Over time, your hearing "comfort level" adapts to higher volumes of sound, so what sounds "normal" can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

• Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards.

After-sales service for Pioneer products

Please contact the authorized Pioneer dealer from which you purchased this unit or an authorized Pioneer service company for after-sales service or questions you may have about the product.

You may contact Pioneer directly as follows:

Do not ship your unit in for repair without contacting Pioneer first. Units sent without a return authorization number will be refused.

In the U.S.A. and CANADA:
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
https://www.pioneerelectronics.com/
PUSA/AboutPioneer/Contact+Us

For warranty information please see the Limited Warranty sheet included with this unit.

Connections

• If your boat's ignition has no ACC position: Be sure to set [PW SAVE] to [ON] (for details, refer to the Operation Manual). The unit will automatically shut off completely after the unit is turned off to prevent battery drain. Otherwise, press and hold SRC/OFF until the display turns off each time you turn the ignition off.
• When using a 2 Ω subwoofer with the rear speaker output, use speakers rated 70 W or higher.
  * Please refer to connections for a connection method.
• The black cable is ground. When installing this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to a metal part of the boat's body. The ground wires of a power amp, this unit, and any other devices must each be connected to the boat separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire, generation of smoke or malfunction.

Two devices connected to the boat separately (ground wires)

*1 Not supplied for this unit

• When this unit is installed in a boat without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.
  

• To prevent a short-circuit, overheating or malfunction, be sure to follow the directions below.
• The graphical symbol placed on the product means direct current.

This unit

1. Wired remote input
   Pioneer marine wired remote control (CD-ME300) can only be connected (sold separately).

Power cord

Perform these connections when not connecting a rear speaker lead to a subwoofer.

Perform these connections when using a subwoofer without the optional amplifier.

In the above case, two 4 Ω subwoofers wired in parallel will represent a 2 Ω load.

1. Black (chassis ground)
   Connect to a common ground point.
2. Yellow
   Connect to the constant 12 V supply terminal.
3. Red
   Connect to terminal controlled by the ignition switch (12 V DC).
4. Blue/white
   Connect to the system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

Power amp (sold separately)

Perform these connections when using an optional amplifier.

Installation

To customer:
This product includes a radio transmitter. According to UNECE Regulation no. 10, vessel manufacturers may impose specific conditions for the installation of radio transmitters into boats. Please check your boat's operation manual or contact the manufacturer or your boat dealer before you install this unit.

• Carefully select a dry mounting location where the unit will not come into contact with water/liquids, which may cause internal damage.
• Not SAE J1171 or UL-1500 certified; Installed unit must be isolated from gasoline fuel source in compliance with 33 CFR §183.410 - Ignition protection, and boat manufacturer instructions.

• Do not install this unit where:
• Optimum performance is obtained when the unit is installed at an angle of less than 60°.
  
• When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.
  

DIN mount installation

1. Insert the supplied mounting sleeve into the dash panel.
2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.
   

When not using the supplied mounting sleeve

1. Line up the holes on the mounting bracket with the holes on the sides of the unit to attach the bracket.
   
2. Screw in one screw on each side to hold the unit in place.
   

Removing the unit (installed with the supplied mounting sleeve)

1. Remove the trim ring.
   
2. Insert the supplied extraction keys into both sides of the unit until they click into place.
3. Pull the unit out of the dash panel.
   

To secure the front panel

The front panel can be secured with the supplied screw.

Installing the microphone

The microphone should be placed directly in front of the boat operator at a suitable distance to pick up their voice clearly.

Carefully select the mounting location to avoid internal damage by water entering the microphone. Areas subject to water splashes should be avoided.

It is extremely dangerous to allow the microphone lead to become wound around the steering column or shift lever. Be sure to install the microphone in such a way that it will not obstruct operation. It is recommended to use cable clamps (sold separately) to arrange the lead.

1. Slide the microphone base to detach it from the microphone clip.
   
2. Install the microphone as follows.
   

Basic operation

MVH-MS310BT

About the main menu

You can adjust various settings in the main menu.

1. Press the M.C. dial to display the main menu.
2. Turn the M.C. dial to select one of the categories below, then press to confirm.
3. Turn the M.C. dial to select the options, then press to confirm.

Frequently used operations

Purpose	Operation
Turn on the power	Press SRC/OFF to turn on the power. Press and hold SRC/OFF to turn off the power.
Adjust the volume	Turn the M.C. dial.
Select a source	Press SRC/OFF repeatedly.
Change the display information	Press DISP repeatedly.
Return to the previous display/list	Press BAND/.
Return to the normal display from the menu	Press and hold BAND/.
Change the display brightness	Press and hold BAND/.
Boost the bass level	Press BASS.

Setup operation

When you turn the ignition switch to ON after installation, the setup menu appears in the display.

1. Turn the M.C. dial to select [LANGUAGE], then press to confirm.
   [ENG] [ESP] [FRA]
2. Turn the M.C. dial to select [CLOCK SET], then press to confirm.
   1. Turn the M.C. dial to adjust the hour, then press to confirm.
      The indicator moves to the minute setting automatically.
   2. Turn the M.C. dial to adjust the minute, then press to confirm.
3. [QUIT:YES] appears.
   To return to the first item of the setup menu, turn the M.C. dial to select [QUIT:NO], then press to confirm.
4. Press the M.C. dial to confirm the settings.

Canceling the demonstration display (DEMO OFF)

1. Press the M.C. dial to display the main menu.
2. Turn the M.C. dial to select [SYSTEM], then press to confirm.
3. Turn the M.C. dial to select [DEMO OFF], then press to confirm.
4. Turn the M.C. dial to select [YES], then press to confirm.

Tuner operation

Receiving preset stations

1. Press SRC/OFF to select [RADIO].
2. Press BAND/ to select the band.
   [FM1] [FM2] [FM3] [AM]
3. Press a number button (1/ to 6/).

Best stations memory (BSM)

1. After selecting the band, press the M.C. dial to display the main menu.
2. Turn the M.C. dial to select [FUNCTION], then press to confirm.
3. Turn the M.C. dial to select [BSM], then press to confirm.

To store stations manually

1. While tuned to the station you want to store, press and hold one of the number buttons (1/ to 6/) until it stops flashing.

USB/iPhone^®/AUX operation

(iPhone source is not available when [USB MTP] is set to [ON] in the SYSTEM settings.)

USB/iPhone

MTP connection

A device installed with Android OS 4.0 or most later versions can be connected to the unit via MTP using the cable supplied with the device. However, depending on the connected device, OS version or the number of files in the device, audio files/songs may not be able to be played back via MTP.

NOTE
If you use an MTP connection, [USB MTP] needs to be set to [ON] in the SYSTEM settings.

AUX

1. Press SRC/OFF to select [AUX IN] as the source.

Bluetooth connection

Up to two Bluetooth mobile devices can be connected simultaneously.

Bluetooth telephone

Basic operations

Purpose	Operation
Answer an incoming call	Press any button when a call is received.
End a call	Press .
Reject an incoming call	Press and hold when a call is received.

Activating voice recognition mode

1. Press and hold and then talk into the microphone to input voice commands.

To exit voice recognition mode, press BAND/.

Making a connection with Pioneer Smart Sync

Pioneer Smart Sync is the application that intelligently brings your maps, messages, and music together.

Do not attempt to operate the application while driving. Make sure to stop your boat in a safe location before attempting to use the controls on the application.

1. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
2. Turn the M.C. dial to select one of the below.
3. Turn the M.C. dial to select [AUTO APP CONN], then press to confirm.
4. Turn the M.C. dial to select [ON], then press to confirm. 6 Connect this unit with the mobile device via USB or Bluetooth. Pioneer Smart Sync on the iPhone/Android device starts automatically.

NOTE
Regardless of whether the [AUTO APP CONN] setting is set to [ON] or [OFF], you can also perform the following to start Pioneer Smart Sync.

• For devices other than a USB-connected Android device, press SRC/OFF to select any source and press and hold the M.C. dial.

Listening to Pandora^®

(Not available when [USB MTP] is set to [ON] in the SYSTEM settings.)

Update the Pandora application to the latest version before use.
Before you start, connect this unit with the mobile device via USB (iPhone only) or Bluetooth.

1. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
2. Turn the M.C. dial to select one of the below.
3. Press SRC/OFF to select [PANDORA].

Listening to Spotify^®

(Not available when [USB MTP] is set to [ON] in the SYSTEM settings.)

Update the Spotify application to the latest version before use.
Before you start, connect this unit with the mobile device via USB (iPhone only) or Bluetooth.

1. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
2. Turn the M.C. dial to select one of the below.
3. Press SRC/OFF to select [SPOTIFY].