Related Manuals for Electrolux SP New R290
Summary of Contents for Electrolux SP New R290
- Page 1 SP New R290 OPERATOR’S MANUAL ENGLISH PAGE 2 Attention: risk of fire – R290 Emission date: July, 2021 Revision: 2 Pag. : 1/28...
- Page 2 In case of loss or damage, it’s possible to ask for a copy to Electrolux Professional SPA, pointing out the information stated on the identification label;...
-
Page 3: Table Of Contents
INDEX SAFETY INSTRUCTIONS ......4 Cleaning and daily sanitizing procedures ..5 EQUIPMENT KIT ........11 TRANPORT TIPS ........11 LIFTING TIPS ..........11 TECHNICAL SPECIFICATIONS ....12 POSITIONING ..........13 CONNECTION TO THE POWER SUPPLY MAINS ............14 ... -
Page 4: Safety Instructions
his appliance is intended for professional 1. SAFETY INSTRUCTIONS use and must be installed in places where it can be checked by qualified personnel. his installation and operation manual is an integral part of the equipment and must o not store explosive substances such as be kept for future consultation. -
Page 5: Cleaning And Daily Sanitizing Procedures
!Caution! WARNING : do not locate multiple o prevent bacteria growth, use only portable socket-outlets or portable power sanitizers approved for plastic and rubber supplies at the rear of the appliance. objects, failure to do so could create a health hazard. WARNING : when positioning the appliance, endure the supply cord is not... - Page 6 top the freezing system and let the machine run with the only auger activated (position O for the small button, position I for the main one) for ten minutes. rovide yourself with a sanitizer suitable for Fig. 1 plastic, rubber and stainless steel objects muchina®).
- Page 7 Caution o avoid electrical shock or contact with moving parts, before proceeding with the disassembling operations, make sure all switches are in “OFF” position and that the main power supply is disconnected. witch off the machine and disconnect the power cable. emove the main cover.
- Page 8 nscrew the security knob in the direction of the arrow (threading on left), then pull out the mixing unit, the bell shaped seal and the bowl gasket on the back (fig.8). emove the drip tray pulling it outward (fig.9). horoughly wash all the removed components with hot water and dish washing, but do not use Fig.
- Page 9 nce performed all these cleaning and sanitizing procedures, it’s possible to reassemble all the components. he correct assembly of the device is essential to prevent leakage of product and damage of the machine. o assemble the machine you will need an approved lubricant (such as aseline).
- Page 10 ubricate the rear of the tank where it meets with the seal to facilitate the reassembling procedures (see fig.14); Fig. 14 eassemble the bowl by positioning it back into its seat, verifying that it faces in the correct direction and it is held in place by its seal (see fig.15).
-
Page 11: Equipment Kit
SANITIZING 2. EQUIPMENT KIT henever the machine has remained unused for some days after been cleaned and sanitized In the packaging of this equipment you will find as described in the chapter 9, the sanitizing also: procedures described below must be performed - operator’s manual, just prior to start-up the machine. -
Page 12: Technical Specifications
other, taking care to maintain the vertical position, as shown by the arrows on the carton. Noise emissions The continuous, equivalent, weighted level of acoustic pressure is below 70 dB. 5. TECHNICAL SPECIFICATIONS In the event of breakdown: Technical and electrical specifications machine’s technical electrical... -
Page 13: Positioning
6. POSITIONING FOR MAINTENANCE WORKER ONLY The installation and subsequent servicing operations must be carried out by skilled members who have been trained to use the device compliance with regulations in force. a) Remove the packing (fig.18) and preserve it in order to reuse for winter storage. -
Page 14: Connection To The Power Supply Mains
7. CONNECTION POWER SUPPLY MAINS FOR SERVICEMAN ONLY Before fitting the plug in the power supply socket, your safety, already mentioned in the previous paragraph, please read the following precautions. machine’s electrical safety only guaranteed when it is connected to a suitable earth system, structured as provided by the national safety current regulations (fig.20). -
Page 15: Control Panel (Fig.21)
8. CONTROL PANEL (FIG.21) A: main switch E (SP2 only): mixing spiral rotation activation switch (E1 left spiral, E2 right spiral) B: refrigerator system management switch (B1 left side, B2 right side) Snowflake: freeze hybrid mode 0: washing Drops: night mode (defrost) C (LIGHT version only): light switch (C1 left side, C2 right side) D (ULTRA version only): light switch (D1 left... -
Page 16: Thermostat Controller
9. THERMOSTAT CONTROLLER The SP machine line is equipped with a digital display (fig. 22) that allows you to view the temperature in each tank. Operation mode The snowflake symbol at the top left of the display, lights up only when the refrigeration system is in operation. -
Page 17: Operating Instructions And Start-Up Procedures
10. OPERATING INSTRUCTIONS AND START-UP PROCEDURES !IMPORTANT! BEFORE STARTING THE MACHINE, CARRY OUT THE CLEANING AND SANITISING PROCEDURES DESCRIBED IN CHAPTER 9. - Dilute and mix the product in a separate container according to the manufacturer’s instructions (see fig.23). NOTE: “mix” is the result of the blending Fig. - Page 18 - Insert the plug into the power socket. - Activate the main switch A; the mixer will automatically start working in SP1 while in SP2 it will be necessary to activate the two mixers through the appropriate switches E1 and E2. Attention Not all products are equally sensitive to nUVA rays and therefore it is possible that some,...
-
Page 19: Special Maintentance
11. SPECIAL MAINTENTANCE Caution Before proceeding with any maintenance operation, it is compulsory to switch off the machine and unplug it from the mains. Condenser cleaning In order to guarantee good cooling system performance, condenser must well cleaned every month. How to reach it: Fig. -
Page 20: Control And Replacement Of Seals
- Cover the machine with the original package to protect it from dust or other contaminating elements. Control and replacement of seals - Place the machine in dry location. EVAPORATOR HARD SEAL Replace every 9 to12 months according to the conditions of use and level of maintenance. -
Page 21: Troubleshooting Guide
13. TROUBLESHOOTING GUIDE NOTE: the following procedures must be performed by a qualified service technician. Problem Possible cause Solution The machine does not cool, space around machine Allow at least 20cm between the or cools only partially and inadequate for ventilation machine and anything next to it;... -
Page 22: Wiring Diagram
14. WIRING DIAGRAM Emission date: July, 2021 Revision: 2 Pag. : 22/28... - Page 23 Emission date: July, 2021 Revision: 2 Pag. : 23/28...
- Page 24 Emission date: July, 2021 Revision: 2 Pag. : 24/28...
- Page 25 Emission date: July, 2021 Revision: 2 Pag. : 25/28...
- Page 26 Emission date: July, 2021 Revision: 2 Pag. : 26/28...
- Page 27 Emission date: July, 2021 Revision: 2 Pag. : 27/28...
- Page 28 Electrolux Professional SPA Viale Treviso 15 33170 Pordenone www.electroluxprofessional.com Emission date: July, 2021 Revision: 2 Pag. : 28/28...