Related Manuals for ABB INCA 1EC Tina
Summary of Contents for ABB INCA 1EC Tina
- Page 1 — S AFET Y PRODU CTS INCA Tina Emergency stop buttons and INCA Tina Safety stop button Product Manual 2TLC172163M0201 Rev.F ORIGINAL INSTRUCTIONS new.abb.com/low-voltage/products/safety-products...
- Page 2 Suitability for use ABB shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer’s application or use of the product. Third party certificates for the products are available at https://new.abb.com/low- voltage/products/safety-products.
-
Page 3: Table Of Contents
Table of Contents 1 Introduction ........................... 4 Purpose of document ......................4 Intended audience ........................4 Reading prerequisites ......................4 Special notes ..........................4 2 Safety .............................. 5 Safety precautions ........................5 3 Product description ........................6 4 Installation ............................. 7 Installation precautions ...................... -
Page 4: Introduction
This document is intended for authorized personnel. Reading prerequisites It is assumed that the reader of this document has knowledge of the following: • Basic knowledge of ABB safety products • Knowledge of machine safety Special notes Pay attention to special notes in the document:... -
Page 5: Safety
Safety Safety precautions The safety precautions must be followed during installation, operation, maintenance and troubleshooting. It is the responsibility of the user to ensure the correct overall functionality. Warning! Carefully read through the entire product manual before using the device. Warning! The devices shall be installed by authorized personnel following applicable Safety regulations, standards and the Machinery directive. -
Page 6: Product Description
INCA 1 Tina v2 is an emergency stop with a red button. INCA 1S Tina v2 is a safety stop with a black button. INCA 1EC Tina is an emergency stop with StatusBus configured for static information output, but it switches to StatusBus configuration when StatusBus communication is detected on the information output. -
Page 7: Installation
Installation • Mount and fit INCA Tina in the cabinet. • Attach and tighten the M22 nut. • See max. tightening torque in chapter “Technical data”. • Connect the terminal block. Installation precautions Warning! All safety functions shall be tested before starting up the system. Testing safety functions After each step the status of the input can be read on the monitoring device. -
Page 8: Connections
Connections 5-pin screw terminal block +24 VDC DYNlink signal input 0 VDC DYNlink signal output Information output * * For INCA 1EC Tina: Information/StatusBus output Warning! Information output signals shall never be used for safety purpose(s). 2TLC172163M0201 Rev.F... -
Page 9: Connection Examples
Three INCA 1EC Tina with StatusBus connected to the DYNlink safety circuit monitored by a safety PLC. The status of each individual INCA 1EC Tina unit can be monitored with a single PLC port in a controller having a StatusBus master. -
Page 10: Functions
Functions LED Indications LED indication Description DYNlink state Green DYNlink input signal, button released/not pressed Green/red flashing DYNlink input open or 0 VDC, Interrupted before this button released/not pressed unit Button actuated/pressed Interrupted in this unit LED Indications for StatusBus LED indication Description Status... -
Page 11: Information Output Signal For Statusbus
Warning! Information output signals shall never be used for safety purpose(s). Information output signal for StatusBus The information output on INCA 1EC Tina has two functions: • Default function and behavior see chapter “Information output signal attributes”. • StatusBus: The information output from several devices with StatusBus functionality, can be connected to one and the same port on a StatusBus master. -
Page 12: Maintenance
(EN 62061:2005+A1:2013+A2:2015, EN ISO 13849-1:2015). Warning! In case of breakdown or damage to the product, contact ABB. Do not try to repair the product yourself since it may accidentally cause permanent damage to the product, impairing the safety of the device which in turn could lead to serious injury to personnel. -
Page 13: Troubleshooting
Troubleshooting LED indications LED indication Probable cause Action Button actuated/pressed Turn the button clockwise and pull it up. +24 VDC connected to Check if there is +24 VDC on DYNlink signal input DYNlink signal input. If yes, check cable connections or the unit before. -
Page 14: Dimensions
Dimensions All dimensions are in mm. Mounting cut-out 2TLC172163M0201 Rev.F... -
Page 15: Technical Data
2TLA030054R0010: INCA 1 Tina v2 Emergency stop button, red button, 5-pin screw terminal block 2TLA030054R0210: INCA 1S Tina v2 Safety stop button, black button, 5-pin screw terminal block 2TLA030054R1400: INCA 1EC Tina Emergency stop button, red button, 5-pin screw terminal block, StatusBus Power supply... - Page 16 Humidity range 35 to 85 % (with no icing or condensation) Housing material Polyamide PA66, Macromelt, thermoplastic polyester PBT, Polypropylene PP, UL 94 V0 Connectors 5-pin screw terminal block Conductor cross section area: 0.25 – 1 mm (AWG 16-24) Wire stripping length: 7 mm Tightening torque 5-pin screw terminal block: 0.25 Nm M22 nut: 0.8 Nm...
-
Page 17: Declaration Of Conformity
Declaration of conformity EC Declaration of conformity [Pending] 2TLC172163M0201 Rev.F... - Page 18 UK Declaration of conformity 2TLC172163M0201 Rev.F...