Sealey SDL15 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to

Wear protective

instructions

gloves

1. SAFETY

1.1.

ELECTRICAL SAFETY

WARNING! It is the user's responsibility to check the following:

‰

Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and

all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical

products. You may obtain an RCD by contacting your local Sealey Stockist.

If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable

Appliance Test) tested.

Electrical safety information, it is important that the following information is read and understood.

1.1.1.

Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.

1.1.2.

Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.

1.1.3.

Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the

correct fuse - see fuse rating in these instructions.

DO NOT pull or carry the appliance by the power cable.

8

DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.

8

DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a

8

qualified electrician.

1.1.4.

This product is fitted with a BS1363/A 13 Amp 3 pin plug.

If the cable or plug is damaged during use, switch the electricity supply and remove from use.

Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.

Class II products are wired with live (brown) and neutral (blue) only, and are marked with the

Class II symbol;

A) Connect the BROWN live wire to the live terminal 'L'.

B) Connect the BLUE neutral wire to the neutral terminal 'N'.

C) After wiring, check that there are no bare wires and ensure that all wires have been correctly

connected.

Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.

DO NOT connect either wire to the earth terminal.

8

Sealey recommend that repairs are carried out by a qualified electrician.

1.2

GENERAL SAFETY

Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the welder.

9

WARNING! Disconnect the welder from the mains power before changing accessories, servicing or performing any maintenance.

‰

Maintain the welder in good condition (use an authorised service agent).

9

Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

9

WARNING! Always wear approved eye or face protection when operating the welder.

‰

Keep the work area clean, uncluttered and ensure there is adequate lighting.

9

Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.

9

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes,

9

Secure non stable workpiece with a clamp, vice or other adequate holding device.

9

DO NOT use the welder for a task it was not designed to perform.

8

DO NOT operate the welder if any parts are damaged or missing as this may cause failure and/or possible personal injury.

8

DO NOT hold the workpiece by hand. Use clamps or a vice (not included) to secure the workpiece. Available from your Sealey stockist.

8

DO NOT let the welder get wet or use in damp or wet locations or areas where there is condensation.

8

DO NOT place heating element close to your face (especially eyes, ears, etc) or other persons or animals.

8

DO NOT allow children or untrained persons to operate the welder.

8

DO NOT operate the welder when you are tired or under the influence of alcohol, drugs or intoxicating medication.

8

DO NOT allow the welder to contact skin.

8

DO NOT inhale any vapour given off by the welder.

8

DO NOT carry the welder with your finger on the power switch, or carry by the power cable.

8

DO NOT use the welder where there are flammable liquids, solids or gases such as paint solvents, etc.

8

DO NOT leave the welder unattended whilst it is switched on.

8

When not in use, switch the welder off, remove plug from the power supply and store the tool in a safe, dry child proof area.

9

© Jack Sealey Limited

75W PLASTIC WELDING REPAIR KIT

MODEL NO:

Hot surfaces

Wear eye

protection

Original Language Version

SDL15

Keep dry

Recommended fuse rating

5 Amp

SDL15

Issue 2 (2,3)

16/06/22