Quick Links
FCC C
OMPLIANCE
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example – use only shielded
interface cables when connecting to computer or peripheral devices). Any changes
or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Acknowledgment & Trademark
All contents are subject to change at any time without notice. No responsibility is assumed for
its use; nor for infringements of patents or other rights of third parties and no patent or license
is implied hereby.
All trademarks are the property of their respective owners.
Safety Notice
1. Do not install or operate the product in high temperature, humidity or dusty environment.
2. Do not attempt to open the cover to repair the product yourself.
3. Never spill liquid of any kind on the product.
4. Always follow instructions on this manual under operating the product.
5. To prevent exposure to laser emanations(harmful to human eyes), do not attempt to
disassemble this unit.
6. Hold CD discs by their edges. Do not touch the surface of the discs.
S
TATEMENT
EN
Summary of Contents for Acer SHD-16S1S
- Page 1 FCC C OMPLIANCE TATEMENT Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 2 7. The drive is designed to be incorporated into a computer-based system or unit which has an enclosing cover. Using the drive alone or in any other configuration is prohibited. Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
-
Page 3: System Requirements
ENGLISH NTRODUCTION Thanks you for your purchasing this DVD-ROM drive. Please read this manual before using the drive in order to take you step-by-step through the process of setting up and installing the DVD-ROM drive. Precautions • Do not attempt to open the drive and service it. Removing the cover may cause exposure to harmful laser beam and electrical voltage. -
Page 4: Hardware Installation Of Atapi/E-Ide Drives
ENGLISH ATAPI/E-IDE D ARDWARE NSTALLATION OF RIVES Turn off PC and disconnect all power cords. Remove the PC cover from computer. Set the Master/Slave jumper on DVD-ROM rear panel according to the following section. Find an empty bay, slide the DVD-ROM into the bay horizontally and mount the drive with 4 screws. - Page 5 ENGLISH CS (CSEL) If you choose the CS setting, the Master/Slave setting will be made automatically depending on your hardware configuration. Connect to Primary/Secondary IDE Port In most of the PC systems, the hard disk drive is always as a Master device and connected to Primary IDE port to boot the operating system.
-
Page 6: Hardware Installation Of Serial Ata Drives
ENGLISH ATA D ARDWARE NSTALLATION OF ERIAL RIVES Turn off your PC and disconnect all power cords. Refer to your PC user's manual to remove the PC cover. Find an empty bay, slide the drive into the bay and mount the drive by using 4 screws. Connect a Serial ATA data cable to the Primary or Secondary Serial ATA port on the motherboard or PCI card of your PC. - Page 7 ENGLISH DVD-ROM D SING THE RIVE Figure: Front view of DVD-ROM Eject/Close Button Push button to eject/close the tray. On/Busy LED The On/Busy LED will be flashing while the DVD-ROM disc is busy. Emergency In case the Eject button isn’t working, insert a small stick or paper clip into this hole to eject the tray.
-
Page 8: Troubleshooting
ENGLISH ROUBLESHOOTING If you meet any trouble during installation or normal use of your DVD-ROM drive, please refer to the following information. Symptoms Action Power is not switched on Check DC power cable connection. No DVD-ROM drive recognition - Check IDE interface connection. Check the collection of MASTER/SLAVE setting.