iHome POWERVALET iW18 - Clock with Dual Charging Manual

FEATURES & FUNCTIONS

BACK PANEL

LEFT PANEL

RIGHT PANEL

TOP PANEL

BOTTOM PANEL

GETTING STARTED

Step One Connecting the Unit

Before use, remove the battery pull tab from the bottom of the unit. Connect the included AC adapter to the DC jack located on the back of the unit and connect the other end to a working wall outlet.

Step Two Setting Your Clock

• Press and hold the Time Set Button until the display flashes.
• Press the – or + Buttons to adjust selections and press Time Set to confirm.

To toggle the clock display between 12/24 hour time, press the Alarm Button while the display is flashing during time setting.

Daylight Savings Time (DST) Switch:

By default, the DST Switch is set to Auto and will automatically adjust the time each March and November.

DISPLAY ICONS

To adjust the brightness of the display, press the Time Set Button repeatedly to cycle through brightness settings, including OFF.

SETTING THE ALARM

Note: Each step must be completed while display is flashing or setting will time-out with any changes saved.

1. Press and hold the Alarm Button for 2 seconds until the alarm time display and alarm icon flash.
2. Press the – or + Buttons to adjust the alarm time to the desired time (hold for rapid setting). Make sure you set the correct AM/PM alarm time. The PM indicator appears to the left of the display.
3. Press the Alarm Button to confirm the alarm time setting. The alarm schedule will flash: 7 (every day), 5 (weekdays) or 2 (weekend only). Press the – or + Buttons to select the desired alarm schedule.
4. Press the Alarm Button to confirm the alarm schedule. 2 beeps will confirm alarm setting is complete. The alarm icon will remain on the display, indicating the alarm is armed.
5. To turn off a sounding alarm and reset it to come on the next day at the same time, press the Alarm Button to reset alarm.

PREVIEWING THE ALARM

Press and release the desired Alarm Button as needed to preview the alarm and to toggle the alarm ON (indicated by the alarm icon) or OFF (no alarm icon).

PROGRAMMABLE SNOOZE

1. To program Snooze, press down on the front of the unit for 2 seconds during normal operation (when no alarm is sounding).
   
2. Press the – or + Buttons to select a snooze time (between 01 and 29 minutes).

WIRELESS CHARGING

Supports:

Place Qi compatible device face up on the charging rest as pictured below:

Check the lightning icon on the iW18 display for charging status:

• Slow blinking icon: Device is charging properly.
• Solid icon: Device is charged.
• Rapid blinking icon: Device is not charging properly. Reposition device.

Note: The lightning icon may continue to blink slowly when iOS devices are fully charged.

Remove metal protective or magnetic case from phone before charging. When charging phone, do not place magnetic-striped or other metal objects on the charger. Doing so could damage the object or this unit. Qi compatible phones with metallic looking finishes will charge normally.

USB CHARGING

Connect the standard size end of a USB cable (not included) to the USB port on the back of the unit and connect the other end to the charging port on your device. (Make sure the unit is plugged into a working outlet in order to charge devices.)

BATTERY BACK-UP

The unit comes with a CR-2450 back-up battery installed to provide continuous alarm operation and clock settings in the event of a temporary power failure. Remove the battery pull tab before use. When the battery icon on the clock display is flashing, it is time to replace the back-up battery. The battery compartment is located on the bottom of the unit.

1. Use a Phillips screwdriver to open the battery compartment door.
   

Lithium batteries can explode or cause burns if disassembled, shorted, recharged, exposed to water, fire, or high temperatures. Do not place loose batteries in a pocket, purse, or other container containing metal objects, mix with used or other battery types, or store with hazardous or combustible materials. Store in cool, dry, ventilated area. Follow applicable laws and regulations for transport and disposal.

IMPORTANT SAFETY INSTRUCTIONS

When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read and follow all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit.

1. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
2. 
   To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
3. 
   Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

FCC INFORMATION

Model: iW18
FCC ID: EMOIW18
IC: 986B-IW18

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions:

This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

• 
  Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

CAN ICES-3 (B)/NMB-3(B), CAN RSS216 / CNR-216

IC Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

WARRANTY

For product support information and warranty please visit: www.ihome.com/support

© 2019 SDI Technologies, Inc. All rights reserved
Questions? Visit www.ihome.com or call 1-800-288-2792 Toll Free

iW18-053119-A

Printed in China