Table of Contents
Quick Links
IMPORTANT INFORMATION
• READ this user's manual before using this user system interface cable.
• KEEP the user's manual handy for future reference.
Do not attempt to use the user system interface cable until you fully understand its
mechanism.
User System Interface Cable:
Throughout this document, the term "user system interface cable" shall be defined as the
following product produced only by Hitachi, Ltd. excluding all subsidiary products.
• User system interface cable (HS2212ECH61H)
The user system or a host computer is not included in this definition.
Purpose of the User System Interface Cable:
This user system interface cable is for connecting the emulator station and user system. This
user system interface cable must only be used for the above purpose.
Improvement Policy:
Hitachi, Ltd. (including its subsidiaries, hereafter collectively referred to as Hitachi) pursues a
policy of continuing improvement in design, performance, functions, and safety of the user system
interface cable. Hitachi reserves the right to change, wholly or partially, the specifications, design,
user's manual, and other documentation at any time without notice.
Target User of the User System Interface Cable:
This user system interface cable should only be used by those who have carefully read and
thoroughly understood the information and restrictions contained in the user's manual. Do not
attempt to use the user system interface cable until you fully understand its mechanism.
It is highly recommended that first-time users be instructed by users that are well versed in the
operation of the user system interface cable.
READ FIRST
I
Table of Contents
Related Manuals for Hitachi H8S/2212 Series
Summary of Contents for Hitachi H8S/2212 Series
- Page 1 Hitachi, Ltd. (including its subsidiaries, hereafter collectively referred to as Hitachi) pursues a policy of continuing improvement in design, performance, functions, and safety of the user system interface cable. Hitachi reserves the right to change, wholly or partially, the specifications, design, user's manual, and other documentation at any time without notice.
- Page 2 Hitachi's warranty. This warranty extends only to you, the original Purchaser. It is not transferable to anyone who subsequently purchases the user system interface cable from you. Hitachi is not liable for any claim made by a third party or made by you for a third party.
- Page 3 This user's manual and user system interface cable are copyrighted and all rights are reserved by Hitachi. No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-copy or machine-readable form, by any means available without Hitachi's prior written consent.
- Page 4 SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism.
- Page 5 WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance.
- Page 6 H8S/2212 Series FP-64E User System Interface Cable (HS2212ECH61H) for E6000 Emulator User’s Manual ADE-xxx-xxx Rev. 1.0 2/4/03 HS2212ECH61HE Hitachi, Ltd.
- Page 7 Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document.
- Page 8 Preface Thank you for purchasing this user system interface cable (HS2212ECH61H) for the Hitachi’s original microcomputer H8S/2212 Series. The HS2212ECH61H is a user system interface cable that connects an H8S/2214 series E6000 emulator (HS2214EPI62H; hereinafter referred to as the emulator) to the IC socket for a FP-64E package for the H8S/2212 series MCU on the user system.
-
Page 9: Table Of Contents
Contents Section 1 Configuration..................1 Section 2 Connection Procedures ..............3 Connecting User System Interface Cable to Emulator Station ......... 3 Connecting User System Interface Cable to User System ..........5 2.2.1 Installing IC Socket ..................... 5 2.2.2 Soldering IC Socket ..................... 5 2.2.3 Inserting Cable Head ................... -
Page 10: Section 1 Configuration
Section 1 Configuration CAUTION Use an IC149-064-175-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-64E package IC socket on the user system. Figure 1 shows the configuration of the HS2212ECH61H user system interface cable for the FP-64E package. To emulator station Screws (M3 x 6 mm) for fixing the cable body... - Page 11 Table 1 lists the HS2212ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2212ECH61H Components No. Component Quantity Remarks Cable body Includes coaxial cable Cable head Consisting of two printed circuit boards IC socket For the FP-64E package Socket cover For installing a FP-64E packaged MCU...
-
Page 12: Section 2 Connection Procedures
Section 2 Connection Procedures Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. - Page 13 Emulator station Cable body connector User system interface cable Screws for fixing the cable body Figure 2 Connecting User System Interface Cable to Emulator Station...
-
Page 14: Connecting User System Interface Cable To User System
Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. -
Page 15: Inserting Cable Head
2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a FP-64E package on the user system with pin 1 on the user system interface cable head, and insert the user system interface cable head into the IC socket on the user system, as shown in figure 3. - Page 16 Screws (M2 x 12 mm) with flat washers Cable head IC socket (IC149-064-175-B51 manufactured by Pin 1 YAMAICHI ELECTRONICS Co., Ltd.) User system Figure 3 Connecting User System Interface Cable to User System...
-
Page 17: Fastening Cable Body
2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Removing Push the remove jig Remove jig Cable head User system Figure 4 Fastening Cable Body... -
Page 18: Recommended Dimensions For User System Mount Pad
Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for a FP-64E package (IC149-064-175-B51: manufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 5 are somewhat different from those of the actual chip's mount pad. -
Page 19: Dimensions For User System Interface Cable Head
Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. 25.0 19.3 63.5 Unit: mm Tolerance: ±0.5 mm Figure 6 Dimensions for User System Interface Cable Head... -
Page 20: Resulting Dimensions After Connecting User System Interface Cable
Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 7. Cable head IC socket Unit: mm (IC149-064-175-B51 Tolerance: ±0.5 mm User system manufactured by YAMAICHI ELECTRONICS Co., Ltd.) Figure 7 Resulting Dimensions after Connecting User System Interface Cable... -
Page 21: Section 3 Installing The Mcu To The User System
Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.29 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first... - Page 22 Screws (M2 x 6 mm) with flat washers Socket cover IC socket (IC149-064-175-B51 manufactured by Pin 1 YAMAICHI ELECTRONICS Co., Ltd.) User system Figure 8 Installing MCU to User System...
-
Page 23: Section 4 User Interface Circuit
Section 4 User Interface Circuit The user system interface cable includes the H8S/2218 microcomputer to emulate the USB function. The H8S/2212 user interface signal includes a interface circuit as shown in figure 9. H8S/2218 HS2212ECH61H User system DrVcc DrVcc 0.1 µF 0.1 µF DrVss DrVss... -
Page 24: Section 5 Verifying Operation
Section 5 Verifying Operation 1. When using the H8S/2214 E6000 emulator for the H8S/2212 Series, turn on the emulator according to the procedures described in the H8S/2214 E6000 Emulator User's Manual (HS2214EPI62HE). 2. Verify the user system interface cable connections by accessing the ports to check the bus states of the pins. -
Page 25: Section 6 Notice
Section 6 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU. - Page 26 7. In the H8S/2212 series, the USB control register and the RTC control register are allocated to external bus areas of area 6 (H’C00000 to H’DFFFFF) and area 7 (H’E00000 to H’FFFFFF), respectively. To access these registers, a bus controller must be set. For details, refer to section 3, MCU Operating Mode, section 6, Bus Controller, and section 14, Universal Serial Bus (USB), in the H8S/2212 Series Hardware Manual.