Page 1
SERVICE MANUAL LED TV LE 5U6500U Model No. MSD64882 Chassis WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians.
Service Manual Model No.: Chapter 1: General Information 1-1. Table of Contents 1. General Information................1-1. Table of Contents 1-2. General Guidelines 1-3. Important Notice 1-4. How to Read this Service Manual ..................3. Location of Controls and Components........... 3-1. Board Location 3-2.
Page 3
Service Manual Model No.: 8. Measurements and Adjustments..…………......8-1. How to enter into the factory model 8-2. How to update software 8-3. How to enter into the Hotel Model 9. Trouble-shooting………….............. 9-1. Simple Check 9-2. Main Board Failure Check 9-3. Panel Failure - 02 -...
Service Manual Model No.: 1-2. General Guidelines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Page 5
Service Manual Model No.: 1-3-6 Safety Check after Repairment in the original positions, or whether there are the positions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that. General Servicing Precautions 1.
Page 6
Service Manual Model No.: Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
Service Manual Model No.: 1-3-8. Photo used in this manual The illustration and photos used in this Manual may not base on the final design of products, which may differ from your products in some way. 1-4. How to Read this Service Manual Using Icons: each icon is described in the table below: Note:...
Page 8
Service Manual Model No.: LE 5U6500U Model 55 inch Screen Size Aspect Ratio 16:9 Resolution 1920*1080 6.0 (GRAY TO Response Time (ms) GRAY) Angel of View 176o Color Display 16.7M No. of Preset Channels 510(DTV);100(ATV) OSD Language English Color System PAL/NTSC/SECAM Audio System DK, BG, I, M, L, L'...
Service Manual Model No.: 3. Location of Controls and Components 3-1 Board Location A Board B Board Description A Board Mainboard Power Supply B Board 3-2 Main Board - 08 -...
Page 10
Service Manual Model No.: 3-2-1 Function Description: Main Board Process signal which incept from exterior equipment then translate into signal that panel can display. 3-2-2 Connector definition Main board connector Power connectors ( J 20 ) Pin number Signal name Pin number Signal name BL- ADJ U ST...
Page 11
Service Manual Model No.: Keypad and remote connector (CN508) Pin number Signal name Description KEY1 KEY0 POWER FOR REMOTE REMOTE CONTROL STANDBY LED_G LAMP GREEN LED_R LAMP RED Speaker connector (CN601) Pin number Signal name Description RSPK+ RSPK+ RSPK- RSPK- LSPK- LSPK- LSPK+...
Service Manual Model No.: 3-3. Power Board 3-3-1 Function Description: Supply power for Main board, Panel. 3-3-2Connectordefinition CON201 Pin number Signal name +12V +12V +5VSTB POWER ON/OFF ON/BK SGND - 11 -...
Page 13
Service Manual Model No.: 3-4. LED Panel MTC500BLU-C09F(CMO:V500HJ1-PE8) - 12 -...
Page 14
Service Manual Model No.: 3-4-1.Connector de finition Name Description Note N.C. No Connection I2C clock (For Vcom tunning) I2C data (For Vcom tunning) N.C. No Connection N.C. No Connection N.C. No Connection (2)(3) SELLVDS LVDS data format Selection N.C. No Connection No Connection N.C.
Page 15
Service Manual Model No.: ERX1- Even pixel Negative LVDS differential data input. Channel 1 ERX1+ Even pixel Positive LVDS differential data input. Channel 1 ERX2- Even pixel Negative LVDS differential data input. Channel 2 ERX2+ Even pixel Positive LVDS differential data input. Channel 2 Ground ECLK- Even pixel Negative LVDS differential clock input...
Service Manual Model No.: 4. Disassemble and assemble 4-1 Remove the Pedestal faces upward 4-2Remove the Back Cover unit. 4-3. Remove the adhesive tape Remove the adhesive tape indicated on the - 14 -...
Service Manual Model No.: 5. Installation Instructions 5-1 External Equipment Connections Accessories Battery User GUIDE Remote Control Antenna Connection Connect one end of a coaxial cable (not included) to the ANT IN jack on the back of your TV/DVD combo, then connect the other end of the cable into the antenna or cable TV wall outlet.
Page 20
INSTALLATION ANTENNA * The TV appearance subject to material object. Note: Aerial connections: IEC(female). Input impendance: 75 unbalanced. STEPS: Be sure both the TV and computer are Power off. 1.Connect VGA and audio cable 2.Connect power cord 3.Power on the TV, switch to PC mode 4.Power on the PC This sequence is very important.
Page 21
INSTALLATION * Subject to material object. AC-INPUT VIDEO/Y HDMI3 SCART DIGITAL AUDIO OUTPUT 100-240V~50/60Hz (COAXIAL) SUPPORTED MODE (PC) V.Freq.(Hz) H.Freq.(KHz) RESOLUTION 640*480 31.47 37.88 800*600 1024*768 48.36 1366*768 47.71 1280*1024 63.98 1920*1080 67.5 (Only for 40") NOTE: PC V.Freq.(Hz) not more than 60Hz. PRESET MODE (HDMI) V.Freq.(Hz) H.Freq.(KHz)
Page 22
AV EQUIPMENT This TV provides one group of AV, one group of YPbPr for convenient connection to VCR, DVDor other video equipment. Please refer to the owner's manual of the equipment to be connected as well. You can use the input terminals on TV set rear as follows. Green (Y) Blue (Pb/Cb) W White(AUDIO-L )
Service Manual Model No.: 5-2 HDMI Connections When the source device(DVD player or Set Top Box) supports HDM How To Connect 1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product). 2.
Page 24
Service Manual Model No.: Cable sample HDMI Cable (not supplied with the product) HDMI to DVI Cable ( not supplied with the product) Analog Audio Cable (Stereo to RCA type) (not supplied with the product) - 22 -...
Page 25
Service Manual Model No.: Power source TO USE AC POWER SOURCE Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard polarized AC outlet. NOTES: Use the attached power cord only. electrician replace the obsolete outlet.
S e r v i c e M a n u a l Mo d el N o . : 6. Operation Instructions 6-1 Front panel controls KEYBOARD Front panel SOURCE MENU V- CH- CH+ Standby 1.SOURCE: Display the input source menu. 2.MENU:...
Page 27
Service Manual Model No.: 6-3 Setting Up Your Remote Control SCREEN Press to change picture aspect ratio. Press to open the on-screen menu.In teletext mode,press to open the INDEX page. Press to navigate the on-screen menu. Press to confirm a selection. Press to return to the previous screen.In teletext mode,press to enter mix mode.
Page 28
Remote Control TELETEXT Teletext is an information system broadcast by certain channels which can be consulted like a newspaper. It also offers access to subtitles for viewers with hearing problems or who are not familiar with the transmission language(cable networks, satellite channels, etc.) Press: You will obtain : This is used to call or exit teletext modes.
Page 32
+1.5V_DDR +1.5V_DDR 56ohm-0402-±1%-1/16W U 1 A 56ohm-0402-±1%-1/16W 主芯片 ,IC Main C h ip ,MSD6 4 8 8 MVE-8-SW,H a ie r,6 4 b it,Qu a d -Co re,BGA95 4 ,SMD,Msta r 0.01uF-0402-X7R-±10%-50V C_DDR3_A0 D_DDR3_A0 C-CSB1 C-DDR3-DQ15 C-CSB2 C-DDR3-DQ31 A-A0 B-A0 UDQ7 UDQ7 C_DDR3_A1...
Service Manual Model No.: Measurements and Adjustments Installation Guide Press "OK" to enter the next prompt menu The installation guide only appear when the TV first time turn on or reset to factory set. Shop mode is the most energy mode. Continue? Please select an OSD language Cancel...
Page 44
DTV Completed Initial Quick Setup. tuning. An installation reminder will appear the next time Enjoy your Haier TV you turn on the TV. Press OK to Exit 7). After tuning is complete, the channels are arranged in a 1.
Page 45
Operation 1.2 )Auto Tuning (DVB-C) 1). Press the MENU button and then press the▼▲ buttons Italy Norway Germany to select the CHANNEL menu and then press the OK button. 2). Press the▼▲buttons to select Auto Tuning and then Greece Poland Luxembourg press the OK button.
Page 46
Operation 2). Press the▼▲buttons to select DTV Manual Tuning 3). The CADTV Manual Tuning screen will pop up. and then press the OK button. Press the▼▲buttons to select(Frequency /Symbol (ks/s/QAM Type QAM) press the OK button to commence the search of that channel. When the signal has been CHANNEL Auto Tuning DTV Manual Tuning...
Page 47
Operation Move: 3.SOUND MENU Use the Arrow Buttons to select the channel you wish to The third item of the MENU is the SOUND MENU. move. Then press the Yellow Button to select Move You can adjust the sound effect here such as function.
Page 48
Operation Automatic Power-down The default pass word is 0000, If you forget the 1.If after 4 hours from switch on and no changes have password, you can use the super password:9443. been made to the TV, for example no channel or volume Block program: Press ▼▲...
Page 49
Operation 8.PVR function 1.Prepare to record the program Select Disk PVR function only works in DTV. Check PVR File System Start From OPTION MENU enter into PVR File System USB Disk In “OPTION MENU”, please choose “check Format Time Shift Size PVR File System”.
Page 50
Operation 2.Record the program (Suggest to format the device by “High Speed Fs...”, As playing the DTV source, choose the channel and which can speed up the record.) click “ record”, the record frame will pop up. Click ” ● ●...
Page 51
Operation 9.Timeshift function Prepare to record the program This TV allows you to pause and record the Please do not unplug the USB storage device currently watched digital program to a USB when the Time Shift function is activated. storage device, and to resume to the point where it was paused.
Page 52
Operation Time Shift limitations: 1. When the Time Shift feature is activated, only the PLAY/PAUSE/STOP/FWD/REV/ VOL+/VOL-/MUTE keys and some basic operation keys (OK/EXIT/navigation keys) are available. 2. Video playback may not be smooth and skip if USB recording speed does not meet the minimum requirements .
Page 53
OK button to enter the USB menu. Pause Prev. Next Stop Repeat ALL Set A Haier Innovation Life ◀▶ Press to select the function icon, press OK button to confirm the function. Press or EXIT button to exit the control bar ▼...
Service Manual Model No.: 8.1 How to enter into the factory model 8.1 How to enter into the factory model 8.1 How to enter into the factory model 1. You can press "source-2-5-8-0" to go into factory setting. Presse the key "exit" to shut the factory setting.
Service Manual Model No.: 8.2 How to update software Haier MSD308C F/W upgrade with USB SOP Step 1: Ready for F/W Upgrade 1.1 Prepare a USB memory . 1.2 Copy the software file (merg.bin) from your computer to the USB memory, and remove it from computer’s USB port!
Service Manual Model No.: 8.3 How to enter into the hotel model 1. You can press "source-1-0-0-1" to go into the hotel model. Presse the key "exit" to shut the hotel model. Content: 1.Hotel Mode: Hotel mode switch Panel key lock 2.Panel Key Lock: Hotel mode can adjust the maximum volume 3.Max Volume:...
Service Manual Model No.: 9. Trouble shooting 9-1. Simple check - 51 -...
Page 58
T.MS6488.U801 Trouble Shooting —Power supply —Display Trouble —Audio Trouble —Function Trouble Author : longshudong Checked By : chenxiangwu POWER Author : Checked By :...
Page 59
Power supply TV Power supply Trouble —— 1、Check ED3for 12V, 1、 Check power board 2、Check ED1 for 5V_STB 1.Check CL7 for 3.3V 1.Check the circuit of UL1. 1、check CD3 for 1.5V 1、Check the circuit of UD1. 1、POWER ON and 1、check the circuit of QD1 Check ED2 for 5V and power board;...
Page 60
Display Trouble 1.abnormal screen —— Check if the V-by-one cable is right and if well connected with the board 1、Reconnect the cable; 2、Change the V-by-one cable; Check if the LED panel is OK Change panel Check if between the V-by-one jack and MSD6488MVE are well soldered Repair the damage circuit...
Page 61
Display Trouble —— 2.white screen Check the power supply for panel Check the V-by-one Check the switch signal on the G- signal from pole of UM1 MSD6488MVE Repair control Change circuit for QM2 MSD6488MVE Check UM1 or Change the panel change UM1 or the V-by-one cable...
Page 62
Display Trouble —— 3. black screen Check BL_ON Signal(5V/3.3V) Change software or change MSD6488MVE Check the ADJ/PWM singnal Change software or change MSD6488MVE Check the power supply for inverter...
Page 63
Audio Trouble —— 1. no sound Check if audio signal Input is normal Repair external Check if the volume is rightly set or if audio equipment mute function is off Set it rightly Check if the output signal on the pin 1 &...
Page 64
Function Trouble —— 1. ATV No channel be find Check the RF cable for RF signal repair external RF equipment Check the Pin11/Pin18/Pin24 of UT1 for 3.3V. 1、Repair the power net connecting to this pin 2、change UT1 Check the RT12 & RT13 for I2C data Repair I2C net Check the CT34 &...
Page 65
Function Trouble —— 2. DTV No channel be find Check the RF cable for RF signal repair external RF equipment Check the CT31 For 3.3V change the LT17 Check the RT12 & RT13 for I2C data Repair I2C net Check the CT34、CT69 for IF signal Repair the Tuner &...
Page 66
Function Trouble —— 3.HDMI, YPbPr, CVBS HDMI no signal 1. HDMI terminal is badly soldered 2. DDC setting is wrong and reset it 3. Change MSD6488MVE 1. YPbPr no signal CVBS no signal 2. YPbPr missing colors 1. Repair the front and end 1.
Service Manual Model No.: 9-3. Pannel failure Failure Mode Part Name Description Phenomena Failure cause Block Defect :TCP cracking or cracking Dim or L/D :TCP Sunken V B/D Vertical bar :TCP lead cracking :ACF bonding short :Awful environment and something electric enter V Dim Vertal gray line into LCD...
Page 68
Service Manual Model No.: Part Name Description Phenomena Failure cause I n c o m i n g I n s p e c t i o n Standard Bright dot dark dot in Dot Defect pannel Bladder between Polarizer and top glass Polarizer Bubble Bladder in Polarizer...
Page 69
Service Manual Model No.: Failure Mode Part Name Description Phenomena Failure cause White Screen B/L normal, only white screen display M a y b e c a u s e d by surge current Black Screen B/L normal, and EDS only Black screen display FIIcker...
Page 70
Service Manual Model No.: Failure Mode Part Name Description Phenomena Failure cause Mechanlcal When Caused Nolse turn panel,appear b y M e c h a n i c a cacophony noise of backlight unit Ripple Connectric circle Causeed by between mechanism and pannel B/L off...
Page 71
Service Manual Model No.: Failure Mode Part Name Description Phenomena Failure cause Brightness B/L unit badness at bottom of LCM Light leakage brighter than normal B / L b r i g h t n e s s Sheet in B/L unit Mechanlcal or B/ asymmetric is uneven...
Page 72
Sincere Forever Haier Group Haier Industrial Park, No.1, Haier Road 266101, Qingdao, China http://www.haier.com Printed in China...