Quick Links
12.992in.
(330mm)
9.843in.
(250mm)
A qualified electrician should complete all required wiring. Models WL400HPS & WL400MH will accept 120, 208, 240
or 277 Volts AC. Models WL400HPST & WL400MHT will accept 120, 277 or 347 Volts AC. Fixtures must be properly
grounded for safety. A mounting suitable for outdoor use and rated for wet locations is required. Follow all applicable
electrical codes and regulations.
Please see below for list of warnings.
WARNING
Electric shock hazard
Disconnect power at circuit breaker or fuse box before
installing or servicing light.
WARNING
Fire hazard
USE MIN 90°C SUPPLY CONDUCTORS. CONNECT TO
SUPPLY IN EXTERNAL JUNCTION BOX ONLY.
Lamp and housing become very hot during use. Ensure
free air circulation around unit to dissipate heat. Avoid
enclosed locations and locations where flammable debris
(leaves, cut grass, etc.) might collect. Avoid locations
where humans or animals might accidentally touch fixture.
WARNING
Fire hazard
USE MINIMUM 125° C SUPPLY CONDUCTORS IF
CORD IS NOT USED.
WARNING
Explosion hazard
Never operate light without securing the lens door. When
light is operating, the gas in the lamp inner arc tube is at
high pressure. Never operate light if the fixture lens or
outer glass envelope of the lamp is broken or missing.
WARNING
Explosion hazard
Wear safety glasses and gloves when handling lamp, High
Pressure Sodium outer envelope is under vacuum and
could implode. Metal Halide outer envelope is pressurized
and could explode if broken.
WARNING
UV hazard
The type of lamp used in this fixture can cause serious
skin burn and eye inflammation from short wave ultra
violet radiation if outer envelope of the lamp is broken or
punctured, and the arc tube continues to operate. Do not
use where people will remain for more than a few minutes.
Certain types of lamps that will automatically extinguish
when the outer envelope is broken or punctured are
commercially available.
17.795in.
(452mm)
ELECTRICAL REQUIREMENTS
WARNING
(Metal Halide Lamps Only)
HID Wall Pack - WL Series
INSTALLATION INSTRUCTIONS
Models: WL400HPS, WL400MH,
FOR OUTDOOR USE ONLY
NOT FOR USE IN HAZARDOUS
ATMOSPHERES
IMPORTANT: Read instruction sheet
carefully before installing fixture. Retain
instructions for future reference.
Lamp Types:
High Pressure Sodium 400 Watt
High Pressure Sodium 400 Watt with Tri-Tap
Metal Halide 400 Watt
Metal Halide 400 Watt with Tri-Tap
12.992in.
(330mm)
9.843in.
(250mm)
Figure 1
MOUNTING & WIRING
1.
Loosen (2) screws, open, and remove fixture lens cover. Set
lens cover aside to prevent damage while installing. (See
Figure 2)
2.
Loosen (4) screws and remove reflector.
3.
Identify supply voltage.
Lens
Cover
Figure 2 (Mount Fixture horizontal)
WL400HPST & WL400MHT
17.795in.
(452mm)
Screws
Hinge
Related Manuals for Intermatic WL400HPS
Summary of Contents for Intermatic WL400HPS
- Page 1 9.843in. (250mm) A qualified electrician should complete all required wiring. Models WL400HPS & WL400MH will accept 120, 208, 240 or 277 Volts AC. Models WL400HPST & WL400MHT will accept 120, 277 or 347 Volts AC. Fixtures must be properly grounded for safety. A mounting suitable for outdoor use and rated for wet locations is required. Follow all applicable electrical codes and regulations.
- Page 2 120 V If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use;...