Maintenance; Specifications; Mounting The Base Unit On A Wall; Troubleshooting - Sony SPP-SS950 Operating Instructions Manual
Hide thumbs
Also See for SPP-SS950:
- Service manual (31 pages) ,
- Operating instructions manual (16 pages) ,
- Operating instructions manual (9 pages)
Available languages
Available languages
To store a number to be dialed via Private Branch Exchange (PBX)
Before entering a phone number in Step 4, do as follows:
1
Enter the outside line access digit (e.g., 9).
2
Press (REDIAL/PAUSE).
To change a stored number
Store a new number, as described previously.
Making calls with speed dialing
1
Press (TALK) and wait until the TALK/BATT LOW lamp lights up.
2
Press (SPEED DIAL).
3
Enter the desired speed dialing number ((0) to (9)).
The phone number stored in the speed dialing number will be dialed.
Paging
You can page the handset from the base unit. Note that you can't page if the
handset is in use.
Note
You can't page the handset when its RING ON/BATT SAVE is set to BATT SAVE.
Maintenance
On handling
• Do not attempt to disassemble the casing. Refer servicing to qualified
personnel only.
• Do not put foreign objects into the base unit. Should any liquid or solid object
fall into the base unit, unplug the unit and have it checked by qualified
personnel before operating the unit any further.
• Do not put anything in the DC IN 9V (external power input) jack.
• Do not drop the unit as a malfunction may result.
On cleaning
• Clean the cabinets with a soft cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine as they may damage the finish of the
cabinet.
• If the charge terminals of the base unit and handset are soiled, wipe them with
a soft cloth or paper.
If you have any questions or problems concerning your phone, please consult
your nearest Sony dealer.
Troubleshooting
Remedy
Symptom
You cannot make or receive
• Place the base unit away from noise sources.
calls.
• Move the handset closer to the base unit.
You hear no dial tone.
• Make sure you set up the base unit correctly.
• Make sure the battery is fully charged.
The phone does not connect at
• Make sure the dialing mode setting (pulse or tone) is
all, even the number you dial is
correct.
correct.
The phone doesn't redial
• Make sure the last dialed number is really the one you
correctly.
want to dial.
You hear five short error beeps
• The number you last dialed exceeds 32 digits
(including the tone and pause digits if used).
when you try to redial.
• The number you last dialed is erased.
You cannot store a speed dial
• Make sure the number (including the tone and pause
digits) does not exceed 16 digits.
number.
• Set the RING ON/BATT SAVE switch to RING ON.
The handset does not ring.
• Move the handset closer to the base unit.
You hear interference during
• Place the base unit away from noise sources.
conversation.
• It is an out-of-range alarm. Move the handset closer to
You hear a beep every second
the base unit within one minute.
during conversation.
• The battery is weak. Charge the battery for more than
You hear a beep every three
12 hours. Note that you cannot use the handset
seconds and the TALK/BATT
without charging it for more than 10 minutes.
LOW lamp flashes.
To page
Press (PAGE).
The handset rings.
When you keep pressing (PAGE),
the handset rings continuously.
Specifications
General
Spread method
Direct-Sequence Spread-Spectrum
Access method
FDMA-TDD
Frequency band
902 – 928 MHz
Operation channel
20 channels
Supplied accessories
AC power adaptor AC-T47 (1)
Telephone line cord (1)
Rechargeable battery pack BP-T18 (1)
Directories (2 sheets)
Wall bracket/stand (1)
Screws (2)
Handset
Power source
Rechargeable battery pack BP-T18
Battery life
Standby: Approx. 7 days (RING ON mode)
Talk: Approx. 4 hours
Dimensions
Approx. 58 x 177 x 46 mm (w/h/d), antenna
excluded
Antenna: 72 mm
Mass
Approx. 250 g, battery included
Base unit
Power source
DC 9V from AC power adaptor
Battery charging time
Approx. 12 hours
Dimensions
Approx. 128 x 58 x 208 mm (w/h/d), antenna
excluded
Antenna: 165 mm
Mass
Approx. 320 g, wall bracket excluded
Design and specifications are subject to change without notice.
Mounting the base unit on a wall
1
Reverse the hang-up tab.
2
Plug the telephone line cord to the LINE jack and the AC power
adaptor to the DC IN 9V jack, and hook the cords.
3
Attach the wall bracket to the center of the base unit. Align the ¢
marks of the wall bracket with those of the base unit.
4
Attach the supplied screws to the wall.
5
Hook the base unit to the screws.
6
Plug the telephone line cord to the telephone outlet, and the AC
power adaptor to an AC outlet. Then raise the antenna so that it
points towards the ceiling.
1
2
AC power
adaptor cord
4
10 cm
5
Tip
To remove the wall bracket, press the lower tabs.
Template for mounting the phone on the wall
To determine the positions for the screws, cut out the template below and use it
as a guide. Consider the weight of the phone when you choose the place to hang
it.
Positions for screws
Approx. 3 weeks (BATT SAVE mode)
3
Wall
bracket
1
2
Telephone
line cord
6
Telephone
outlet
AC power
AC outlet
adaptor
