Page 1
USER'S MANUAL Please read this manual carefully before using your television and keep this manual In a good place for future reference. MODEL: L1509-A, L15A09A, L1709-A, L17A09, L1909-A, L19A09, L2009-A, L20A09, L1510A-A, L15A10A, L1910A-A, L19A10A, L1510B-A, L15A10B,L1910B-A, L19A10B, L1911W-A, L19A11W,...
To users: Thank you for using our LCD-TV. Before connecting the LCD-TV and turning the power on, please read this book carefully. Please keep this book for later use. CONTENT Safety Notice Items... Front Panel Controls... Connection Options... Remote Control Key Functions...
Never put the unit in direct sunlight or near heat sources; l Allow enough space for proper ventilation; l Please keep water away from the LCD-TV . If water comes in contact with the LCD-TV, disconnect the power cord from the power source, then wipe the set with a dry soft cloth;...
Volume down / Left orientation to adjust the item in the OSD VOL+ Volume up / Right orientation to adjust the item/Press to enter 5. CH- TV channel down / to select the item in the menu TV channel up / to select the item in the menu 6. Power indicator...
AUDIO IN Earphone port Antenna Input Connect cable or antenna signals to the TV, either direc- tly or through your cable box. And the AC power supply switch is on the back of the set) COMPONENT Input Connect a component...
Buttons on the remote control Stand By MUTE Display current input signal information TV channel number select POWER Set time to change the TV into the standby status after a period of preset TV/AV time. NICAM/A2 Stereo select EXIT Quick TV channel switch(return to the...
Remote Control Installing Batteries 1.Slide open the cover of the battery compartment on the back of the remote control. 2.Load two 5# alkaline batteries in the compartment. (plus and minus poles to respective mark) 3.Replace the cover of the battery compartment. Precautions Make sure that there is no obstacle between the remote...
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) ANT IN NOTE: All cables shown are not included with the TV RF coaxial wire (75 ohm) To improve picture quality in a poor signal area, purchase and install a signal amplifier.
Connection Instructions VGA Input You can use your LCD-TV as a monitor for your personal computer using a VGA cable (not supplied). Connection and use steps: 1.Read the user guide supplied with your computer and ensure that it has a VGA connector;...
1.Read the user guide supplied with your AV devices and ensure that it has S-Video connectors; 2.Make sure that the power of the LCD-TV and the AV device are off; Connection Option 1 Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
Note: The audio cable included with the TV should be used when connected with PC/ COMPONENT/SVIDEO. One side connected with the AUDIO IN terminal on the TV and the other side with right and left track connected with the corresponding terminals of other equipment.
Note: The display of the input mode will disappear in about 8 seconds. The display will appear on the screen when the TV is turned on the first time: (Different displays for different countries, please see the real set) AUTO SEARCH...
You can use the number keys on the remote control to directly select TV channels. The LCD-TV can store up to 100 channels , and you can press the keys on the remote control or on the panel to make a selection.
Menu Operations * In this manual, the OSD (On Screen Display) may be different from your TV s because it is just an example to help you with the TV operation. Press TV/AV to select the input source, and the menu in the different source is different .
Menu Operations Picture Menu Options continued 3.Press V+/V- button to increase and decrease the level to adjust the selected option to your preference . 4. Repeat step 2 and step 3 until desired picture quality has been achieved . Function: BRIGHTNESS :Adjust the brightness of the picture .
4. Repeat step 2 and step 3 until desired sound quality has been achieved .. Function : VOLUME : Adjust the volume of your TV BALANCE : Adjust the balance of the audio output from left to right . When indication value of balance increases toward 100 , sound of the left speaker becomes weaker .
4. Repeat step 2 and step 3 until desired picture quality has been achieved . Functions: 1. INPUT SOURCE : Display current mode . There are PC , COMPONENT , HDMI, TV, SCART, SVIDEO to display 2. LANGUAGE: Used to select the OSD language. 3. TXT LANGUAGE: To switch the teletext languages.
PROG.SET:Opted for setting up start condition. Press P+/- button to select it. Press V+/- button, sources can be swapped in HDMI/COMPONENT/PC/ SVIDEO/SCART/TV/OFF mode. After setup, the set mode will be entered if the television is switched off and on again. To set off, the television will memory the off-mode.
TV after turn off it. (Eg., When INITIAL VOLUME is set to 50, you can still adjust the volume above or below 50 by V+/- . If the TV is turned on the second time, the volume will resume 50) CLEAR LOCK: Press P+/- button to select it.
1. Press MENU and V+/V- button until the following menu appears on the screen Note: This menu is only appears in TV mode . 2. Press P+/P- button to enter the tuning menu and to go up and down to select the desired option .
Menu Operations Tuning Menu Options Continued SOUND SYSTEM : Select the TV standard system from DK,I,L/L',BG SKIP : If you want skip a channel , press V+/V- to select ON , and this channel will be skip next time when you press P+/P- . But you can press digits button to select the channel .
Some menu related function are not available in TELETEXT mode. MENU and AUTO AD control functions are not available in TELETEXT mode. If the TV is switched on by POWER after off in TELETEXT mode, or press TV/AV or PC button, the TELETEXT mode will disappear automatically.
Page 23
TEXT Button Press TEXT to enter Teletext mode and only the text page can be visible . MIX Button Press MIX button to enter Teletext mode and both the TV picture and text page can be visible. TIME While in normal TV mode only, pressing the button TIME will display the teletext time in the top right corner for a few seconds.
2.The TV set must only be repaired by a qualified registered service person. Never attempt to remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire. Verify if the television is properly plugged.
Note Warranty card is only for the special countries and areas Note: All specifications are subject to change without notice. All quality are approximate value. L1510A-A, L15A10A, L1510B-A, L15A10B, L1509-A, L15A09, PAL/SECAM-B/G,I,D/K,L,L 1.5W+1.5W COMPONENT input PC input Audio input SCART...