1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Projector
  5. ED-X20EF
  6. Service manual

Hitachi ED-X20EF Service Manual

Hide thumbs
Table of Contents

Quick Links

SERVICE MANUAL
Warning
The technical information and parts shown in this
manual are not to be used for: the development,
design, production, storage or use of nuclear, chemical,
biological or missile weapons or other weapons of
mass destruction; or military purposes; or purposes that
endanger global safety and peace. Moreover, do not
sell, give, or export these items, or grant permission for
use to parties with such objectives. Forward all inquiries
to Hitachi Ltd.
Be sure to read this manual before servicing. To assure safety from fi re, electric shock, injury, harmful
radiation and materials, various measures are provided in this Hitachi Multimedia LCD Projector. Be
sure to read cautionary items described in the manual to maintain safety before servicing.
1. When replace the lamp, to avoid burns to your fi ngers. The lamp becomes too hot.
2. Never touch the lamp bulb with a fi nger or anything else. Never drop it or give it a shock. They may
cause bursting of the bulb.
3. This projector is provided with a high voltage circuit for the lamp. Do not touch the electric parts of
power unit (circuit) and power unit (ballast), after turn on the projector.
4. Do not touch the exhaust fan, during operation.
5. The LCD module assembly is likely to be damaged. If replacing to the LCD LENS/PRISM assembly,
do not hold the FPC of the LCD module assembly.
6. Use the cables which are included with the projector or specifi ed.
1. Features ------------------------------------------------------ 2
2. Specifi cations ----------------------------------------------- 2
3. Names of each part ---------------------------------------- 3
4. Adjustment --------------------------------------------------- 5
5. Troubleshooting -------------------------------------------11
6. Service points --------------------------------------------- 15
7. Wiring diagram -------------------------------------------- 31
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
Multimedia LCD Projector
YK
Caution
Service Warning
Contents
8. Disassembly diagram ----------------------------------- 40
9. Replacement parts list ---------------------------------- 53
10. RS-232C communication ------------------------------ 54
11. Block diagram --------------------------------------------- 64
12. Connector connection diagram ----------------------- 65
13.Basic circuit diagram ------------------------------------ 66
November 2006
No.0580E
ED-X20EF
(M1-20ED)
Table of Contents
loading

Related Manuals for Hitachi ED-X20EF

Summary of Contents for Hitachi ED-X20EF

  • Page 1: Table Of Contents

    Be sure to read this manual before servicing. To assure safety from fi re, electric shock, injury, harmful radiation and materials, various measures are provided in this Hitachi Multimedia LCD Projector. Be sure to read cautionary items described in the manual to maintain safety before servicing.

  • Page 2: Features

    ED-X20EF (M1-20ED) 1. Features • High Brightness • Low Noise • Rich Connectivity • Compact Body 2. Specifications Drive system TFT active matrix Liquid crystal Panel size 1.6cm(0.63 type) panel Number of pixels 1024 (H) x 768 (V) Lamp 160W UHB Video : Analog 0.7Vp-p(75Ω...

  • Page 3: Names Of Each Part

    ED-X20EF (M1-20ED) 3. Names of each part Projector (1) Lamp cover HOT! (1) (2) (3) The lamp unit is inside. (2) Focus ring (3) Zoom ring (4) Control panel (5) Speaker (10) (9) (8) (11) (6) Elevator knobs (x 2)
  • Page 4 ED-X20EF (M1-20ED) Control panel (1) STANDBY/ON button (4) (5) (6) (2) INPUT/ENTER button (3) MENU button LAMP INPUT/ STANDBY/ON ENTER It consists of four cursor buttons. MENU TEMP (4) POWER indicator POWER (5) TEMP indicator (6) LAMP indicator Remote control...

  • Page 5: Adjustment

    ED-X20EF (M1-20ED) 4. Adjustment 4-1 Before adjusting 4-1-1 Selection of adjustment When any parts in the table 4-1 are changed, choose the proper adjusting items with the chart. Table 4-1: Relation between the replaced part and adjustment Adjustment Replaced White...
  • Page 6 ED-X20EF (M1-20ED) 4-2 Flicker adjustment (V.COM adjustment) Test pattern for the adjustment Adjustment procedure 1. Use DAC-P - V.COM - R: in the FACTORY MENU to adjust so that the flicker at the center of 128/255 the screen is less than the flicker at the periphery.
  • Page 7 ED-X20EF (M1-20ED) 4-5 White balance adjustment (visual inspection) Preparations 1. Perform these adjustments after the adjust- 2. Reset gamma correction before adjustment. Place the cursor on [GAMMA] in the FACTORY ments described in Section 4-5. MENU, press the [RESET] key and select RESET.
  • Page 8 ED-X20EF (M1-20ED) 4-6 Color uniformity adjustments Preparations 1. Perform these adjustments after the adjustments 5. Adjustment point No.1 should not be adjusted, described in the section 4-6. because it controls the brightness of the entire 2. Make a color uniformity adjustments for the fol- screen.
  • Page 9 ED-X20EF (M1-20ED) Adjustment procedure 1 (When a color differential meter is used) Note: Since excessive correction may lead to a 1. First adjust the [MID-1] tone [G:]. correction data overview during internal 2. Select adjustment point [No.2][G:]. calculations, use the following values for When the background is not [G] monochrome, reference.
  • Page 10 ED-X20EF (M1-20ED) Adjustment procedure 2 (visual inspection) same color as measurement point [No.1]. 1. First adjust [MIN] tone [G:]. Adjustment technique: 2. Select [No.2] [G:]. First, adjust [B:] of the point whose color is to If the background is [G] monochrome, press the...

  • Page 11: Troubleshooting

    ED-X20EF (M1-20ED) 5. Troubleshooting Check points...
  • Page 12 ED-X20EF (M1-20ED) Power can not be turned on *: Be sure to unplug the power cord before measuring resistance. voltage Measure supplied at pins (7) resistance* 0Ω and (11) of E800 on the PWB between pins (7) and (11) of...
  • Page 13 ED-X20EF (M1-20ED) Lamp does not light *: Be sure to unplug the power cord before measuring resistance. What is the state of Light LAMP indicator D303 during operation? Is the LAMP installation install the Lamp correct? Not light the voltage YES “L”=0V...
  • Page 14 ED-X20EF (M1-20ED) Picture is not displayed. Confirm the splash the LCD Panels screen and the user menu CPC40 connector 54104/54132 connection to the MAIN displayed correctly? board. PWB assembly MAIN LCD/Lens prism assembly all of the pictures from video, PWB assembly MAIN...

  • Page 15: Service Points

    ED-X20EF (M1-20ED) 6. Service points 6-1 Lead free solder [CAUTION] This product uses lead free solder (unleaded) to help preserve the environment. Please read these instructions before attempting any soldering work. CAUTION Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead free solder can splatter at high temperatures (600˚C).
  • Page 16 ED-X20EF (M1-20ED) 6-2 Replacing The LCD/PRISM assembly You should not replace separately the parts of the LCD/PRISM assembly. In case of a failure in any parts of LCD/PRISM assembly, replace the whole LCD/PRISM assembly. Do not disassemble the unit because replacement of separate parts is not possible.
  • Page 17 ED-X20EF (M1-20ED) 3. Maintenance point Optical filter Each color part has same construction. By using swab and air duster, you can easily remove dust from panel and optical filter. Panel Actual formation Separated formation 4. Cleaning the panels and optical filters (1) Turn on the set and lit on the lamp.
  • Page 18 ED-X20EF (M1-20ED) 6-4 Putting batteries WARNING Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environ- ment.
  • Page 19 ED-X20EF (M1-20ED) 6-5 Cleaning up dust from multilens 1. Preparation Please prepare cleaning tools and materials as follows. (1) Air duster (Dust blower, spray can) (2) Swab for cleaning "Cotton stick L147" (3) Vacuum cleaner 2. Put the projector on the stable stand.
  • Page 20 ED-X20EF (M1-20ED) 5. Cleaning the multilens (1) By using the air duster, remove the dust on multilens. (2) Remove the dust on the ML-A surface using the air duster, then wipe the surface. Remove LAMP CLAP first. Remove DUST PROOF GLASS next.
  • Page 21 ED-X20EF (M1-20ED) 6-6 Air filter If the air fi lter becomes clogged by dust or the like, internal temperatures rise and could cause a fi re, a burn and/or malfunction to the projector. When the indicators or a message prompts to clean the air fi lter, clean the air fi...
  • Page 22 ED-X20EF (M1-20ED) 6-7 Lamp HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
  • Page 23 ED-X20EF (M1-20ED) Replacing the Lamp A lamp has fi nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
  • Page 24 ED-X20EF (M1-20ED) 6-8 Other care WARNING Before caring, make sure the power switch is off and the power cable is not plugged in, and then allow the projector to cool suffi ciently. The care in a high temperature state of the projector could cause a burn and/ or malfunction to the projector.
  • Page 25 ED-X20EF (M1-20ED) 6-9 Notice of AUTO adjustment Use of AUTO adjustment with the image through RGB input optimizes V_POSI, H_POSI, H_SIZE and H_PHASE automatically. In case that projected image has dark tone around its peripheral, AUTO operation sometimes makes artifacts in the image, shifts capture area and so on.
  • Page 26 ED-X20EF (M1-20ED) 6-10 How to inactivate the security functions This projector is equipped with security functions. (1)MyScreen PASSWORD The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and pre- vent the currently registered MyScreen image from being overwritten.
  • Page 27 PIN BOX (ID Inquiring Code) 2. Send HITACHI sales company the Inquiring code (10 digits) to inquire the correct PIN code. 3. With the PIN BOX menu displayed, input the correct PIN code. Enter the correct PIN CODE that HITACHI sales company informed.
  • Page 28 ED-X20EF (M1-20ED) 6-12 Related Messages When the unit’s power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.
  • Page 29 ED-X20EF (M1-20ED) 6-13 Regarding the indicator lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the mean- ings as described in the table below. Please respond in accordance with the instructions within the table.
  • Page 30 LAMP ALARM Select the lamp alarm level. 3 Level ↔ 1 Level ↔ None STARTUP TYPE Select the startup screen type. 1 : shows Hitachi Logo 2 : No Hitachi Logo SOFT RESET If this is executed, all of the user data is initialized.Never use it when not required.

  • Page 31: Wiring Diagram

    ED-X20EF (M1-20ED) 7. Wiring diagram...
  • Page 32 ED-X20EF (M1-20ED)
  • Page 33 ED-X20EF (M1-20ED)
  • Page 34 ED-X20EF (M1-20ED)
  • Page 35 ED-X20EF (M1-20ED)
  • Page 36 ED-X20EF (M1-20ED)
  • Page 37 ED-X20EF (M1-20ED)
  • Page 38 ED-X20EF (M1-20ED)
  • Page 39 ED-X20EF (M1-20ED)

  • Page 40: Disassembly Diagram

    ED-X20EF (M1-20ED) 8. Disassembly diagram (See Notice 1)
  • Page 41 ED-X20EF (M1-20ED)
  • Page 42 ED-X20EF (M1-20ED) Notice 1. The step of the disassembly / The step of the assembly. Disassemble the projector in order of 1, 2, 3, 4, 5, 6 and 7 as shown in the diagram. Assemble the projector in order of 7, 6, 5, 4, 3, 2, and 1 as shown in the diagram.
  • Page 43 ED-X20EF (M1-20ED) Notice 2. Detach and attach the upper case. Follow the procedure below to detach and attach the upper case. When disassembling a. Remove the Lamp door. CAUTION The lamp door must be removed before the upper case when disassembling the machine. If the upper case is detached with the lamp door installed, the MAIN board might be damaged.
  • Page 44 ED-X20EF (M1-20ED) c. Detach the upper case CAUTION When detaching the upper case. Detach the circle point side fi rst. Otherwise, upper case will be damaged. Make sure not to damage the upper case ribs (square pointed). Make sure not to touch reverse side of main board.
  • Page 45 ED-X20EF (M1-20ED) When assembling a. Tighten 7 screws on the bottom and 3 screws on the rear after attaching the upper case with the lamp door separated. In order not to make a gap between the upper and the bottom cases, tighten these screws while pressing down the upper case in the direction of the arrow.
  • Page 46 ED-X20EF (M1-20ED) 4. Detaching and attaching the Panel Fan Duct assembly When disassembling Remove 1 screw and unhook the panel fan duct assembly as shown in the diagram. Lamp fan Lamp fan wire Tape Thermister Panel fan duct assembly Push each of hooks in the direction of the arrows, while remove / tighten this screw.
  • Page 47 ED-X20EF (M1-20ED) 5. Attaching / Detaching the optics unit (1) Remove the three screws as shown in the diagram. And detach the optics unit vertically. (2) Put the optics unit on the bottom case, and tighten screws in order of 1, 2 and 3 as shown in the diagram.
  • Page 48 ED-X20EF (M1-20ED) 8. Attaching the PWB assembly MAIN Note: Use the suitable screw for each screw holes when attaching the main board. Black screw (Tapping screw) White screw (Meter screw) 9. Replacing the air filter. Note: (1) Make sure to fit the concave part of the air filter to the convex part of the filter case.
  • Page 49 ED-X20EF (M1-20ED) 10. Replacing the lamp unit CAUTION When replacing the lamp unit, never detach the three springs. Otherwise, it will be impossible to reuse the lamp unit. Lamp unit Lens fixation springs (3 pieces) Note: When detaching the lamp unit, detach the connector side first.
  • Page 50 ED-X20EF (M1-20ED) 11. Replacing the exhaust fan Be sure to do the following works before changing the exhaust fan. a. Prepare the following replacement parts. Exhaust fan(P#: GS01411) ....1pcs Fan cushions(P#: MS01611) .....1set Fan cushion A ......2pcs Fan cushion B ......1pcs Fan cushion C ......1pcs...
  • Page 51 ED-X20EF (M1-20ED) 12. Replacing the control button Be sure to do following works before changing the control button. a. Make sure the contens of new control button assembly (P#: PC07081) Control button ........1pcs Cushion A ..........1pcs Cushion B ..........3pcs b. Stick 4 pieces of the cushions to the control button.
  • Page 52 ED-X20EF (M1-20ED) 14. Replacing the BOTTOM CASE Be sure to do following works before changing the BOTTOM CASE. a. Make sure the contents of the SP cushion assembly (P#:MU04391) Cushion A ..........2pcs Cushion B ..........2pcs (circle) b. Stick the 4 pieces of the cushions to the BOTTOM CASE.

  • Page 53: Replacement Parts List

    PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components, read carefully, the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the projector through improper servicing. [ ED-X20EF ] SYMBOL PARTS SYMBOL...

  • Page 54: Rs-232C Communication

    ED-X20EF (M1-20ED) 10. RS-232C communication RS-232C cable(Cross) CONTROL port RS-232C port of the projector of a computer - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR...
  • Page 55 ED-X20EF (M1-20ED) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+ ‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
  • Page 56 ED-X20EF (M1-20ED) Command Data Names Operation Type Header Action Type Setting Code Power Turn off BE EF 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 06 00 BA D2 01 00 00 60 01 00...
  • Page 57 ED-X20EF (M1-20ED) Command Data Names Operation Type Header Action Type Setting Code User Gamma Pattern BE EF 06 00 FB FA 01 00 80 30 00 00 9 step gray scale BE EF 06 00 6B FB 01 00 80 30...
  • Page 58 ED-X20EF (M1-20ED) Command Data Names Operation Type Header Action Type Setting Code COLOR TEMP GAIN B BE EF 06 00 8C F5 02 00 B3 30 00 00 Increment BE EF 06 00 EA F5 04 00 B3 30 00 00...
  • Page 59 ED-X20EF (M1-20ED) Command Data Names Operation Type Header Action Type Setting Code ASPECT BE EF 06 00 9E D0 01 00 08 20 00 00 16:9 BE EF 06 00 0E D1 01 00 08 20 01 00 14:9 BE EF...
  • Page 60 ED-X20EF (M1-20ED) Command Data Names Operation Type Header Action Type Setting Code COMPUTER 1 SYNC ON G OFF BE EF 06 00 5E D7 01 00 10 20 02 00 AUTO BE EF 06 00 CE D6 01 00 10 20...
  • Page 61 ED-X20EF (M1-20ED) Command Data Names Operation Type Header Action Type Setting Code MUTE TURN OFF BE EF 06 00 46 D3 01 00 02 20 00 00 TURN ON BE EF 06 00 D6 D2 01 00 02 20 01 00...
  • Page 62 ED-X20EF (M1-20ED) Command Data Names Operation Type Header Action Type Setting Code MENU POSITION V BE EF 06 00 40 D7 02 00 16 30 00 00 Increment BE EF 06 00 26 D7 04 00 16 30 00 00...
  • Page 63 ED-X20EF (M1-20ED) Command Data Names Operation Type Header Action Type Setting Code MY BUTTON-1 COMPUTER1 BE EF 06 00 3A 33 01 00 00 36 00 00 COMPUTER2 BE EF 06 00 FA 31 01 00 00 36 04 00...

  • Page 64: Block Diagram

    ED-X20EF (M1-20ED) 11. Block diagram...

  • Page 65: Connector Connection Diagram

    ED-X20EF (M1-20ED) 12. Connector connection diagram Connector connection diagram...

  • Page 66: Basic Circuit Diagram

    ED-X20EF (M1-20ED) 13. Basic circuit diagram Parts with hatching are not mounted. CONFIDENTIAL DOWN 56.9KHz I002 I001 KSM-2003LM2EL KSM-2003LM2EL Vout Vout C012 C002 100p-C 100p-C 1005 1005 C011 C001 1.0/10 1.0/10 R003 1005 APRC01 APRC02 APRC03 APRC04 PWB assembly REMOTE (M1-20ED)
  • Page 67 ED-X20EF (M1-20ED) CONFIDENTIAL ET01 3114-15FABNS1XN SYNC VCLK PLUG ET04 501568-14H ET02 3175-09M RT11 RT12 1005 1005 ET05 SH-04H RT01 RT02 IT01 DS14C232CM RT03 RT04 ET03 JY-3542*01-250 Dout1 Rin1 Rout1 Din1 RT08 RT05 Dout2 Din2 RT09 RT06 1005 1005 2.2K Rin2...
  • Page 68 ED-X20EF (M1-20ED) MEMO...
  • Page 69 CONFIDENTIAL Warning POWER UNIT (BALLAST) 1 (M1-20ED) For handling of the circuit diagram, refer to the warning on the cover.
  • Page 70 CONFIDENTIAL Warning POWER UNIT (BALLAST) 2 (M1-20ED) For handling of the circuit diagram, refer to the warning on the cover.
  • Page 71 CONFIDENTIAL Warning POWER UNIT (CIRCUIT) (M1-20ED) For handling of the circuit diagram, refer to the warning on the cover.
  • Page 72 CONFIDENTIAL +3.3VPW I201 I201 I201 DIGITAL INPUT PORT PW190 PERIPHERALS PW190 DISPLAY PORT PW190 R2C4 CH0CK IN0CLK IN0CLP CH0CP NC-D13 GCLK R2C5 DCLKOUT DCLK CH0PE IN0PEN IN0CST CH0CS NC-E18 1005 R2C6 *R2K0 CH0VB IN0VBI NC-D14 1005 CH0AH IN0AHS NC-A12 1005 1005 CH0HS CHDEN...
  • Page 73 CONFIDENTIAL L251 I201 1608 RESETN PW190 R200 2.5V 65mA 1005 R203 AC15 AC15 1.0K R217 AE16 AE16 Q201 1005 AF16 AF16 C273 JUMPER R DTC114EUA AC16 2010 AC16 N251 R201 AD15 0.01/16 AD15 EMU-RESET R218 I251 1005 AE15 AE15 S29AL016D70TFI010 R205 2010 AC14...
  • Page 74 CONFIDENTIAL +3.3V R376 CPU-RESET S309 1005 I301 SKHHLMA010 R371 R379 RN5VD26C RESETN 1005 Q372 1005 SRC1202EF C390 0.1/10 1005 GND1 OUTTEMP OUTTEMPP TEMP D302 R332 INTEMP 330 1 LED-TEMP 1005 SML-210VT LAMP D303 R333 330 1 LED-LAMP 1005 SML-210VT JUMPER R E304 D301 ZH-02H...
  • Page 75 CONFIDENTIAL 240mA 495mA R836 R835 1005 1005 MOUSE Q809 2SC5343UFG PWRC I801 SI-3010KM 15.5V-Panel I892 L816 C823 I808 SN74LVC1G32DCK ->TC7SZ32FTE85L MM1661JHBE 0.033/16 1.8V-CPU C6-K3LA C824 I802 I803 +1.8VCPU Cont MM1663DHBE MM1663DHBE 1005 470p R811 C814 C816 I807 RC_EN56 1005 TPS40222DR Cont Cont NC-6...
  • Page 76 CONFIDENTIAL TG part for BiNA5 I401 CXD3540GB from I808 CXD3540GB 3/3 I401 controlled by POWER5 L401 CXD3540GB I401 [email protected] 2518 CXD3540GB CXD3540GB 1/3 +1.8VP VDDI-D4 VSS-A1 CXD3540GB 2/3 VDDI-D7 VSS-A2 R401 R431 HST_R VDDI-D8 VSS-A7 C401 C402 DRE9 R1IN9 R1OUT11 RD1-11 VST_R 10/6.3...
  • Page 77 CONFIDENTIAL R Panel Part for BiNA5 XGA from I802 from I801 controlled by POWER6 controlled by POWER7 70mA 80mA JUMPER R R534 I502 TC7SG125FU 1005 R544 Q533 C521 SHCLK_R IN_A 2SC5343UFG R543 R531 1005 10/16 OUT_Y MVK/SKV R545 1005 1005 R538 C522 GCFB_R...
  • Page 78 CONFIDENTIAL G Panel Part for BiNA5 XGA from I802 from I801 controlled by POWER6 controlled by POWER7 70mA 80mA JUMPER R R634 I602 TC7SG125FU 1005 R644 Q633 C621 SHCLK_G IN_A 2SC5343UFG 1005 R643 R631 10/16 OUT_Y MVK/SKV R645 R638 1005 1005 C622 GCFB_G...
  • Page 79 CONFIDENTIAL B Panel Part for BiNA5 XGA from I801 from I802 controlled by POWER7 controlled by POWER6 70mA 80mA JUMPER R R734 I702 TC7SG125FU 1005 R744 Q733 C721 SHCLK_B IN_A 2SC5343UFG R743 R731 1005 10/16 OUT_Y MVK/SKV R745 R738 1005 1005 C722 GCFB_B...
  • Page 80 CONFIDENTIAL *LV01 2518 JUMPER R GND1 RV48 RV49 DSUB1_B RV50 DSUB1_G 1005 DSUB1_R 1005 1005 DSUB1_H DSUB1_V RV54 75-1% 1 1005 QV09 RV47 RV46 2SC5343UFG GND1 1005 1005 CV33 RV42 RV61 QV04 10/6.3 2SA1980UFG 2125 *QV12 *QV13 *QV14 1005 1005 RV52 SRC1202EF SRC1202EF...
  • Page 81 CONFIDENTIAL *LS01 2518 RS05 RS06 1005 RS04 1005 GND1 1005 DSUB2_B DSUB2_G *RS90 DSUB2_R APDG *RS91 1005 QS02 SRC1202EF 1005 *RS92 ES01 1005 3114-15FA *CS03 10/6.3 CS09 APCL 2125 *IS02 EL8302IUZ-T7 *RS34 1.0p-C 560-1% HS10 INA+ INA- 1005 SC200JT *RS37 SYNC 1005 2125...
  • Page 82 CONFIDENTIAL RA40 POWER7 100 1 RA42 1005 POWER5 100 1 1005 IA03 MM1665AHBE CA36 Cont 470p 1005 NC-6 RA41 NC-7 NC-2 +5VAUDIO Vout 1005 IA01 +6.6V BD3870FS CA54 0.33/10 VIN1 MPEG Audio R - in PL_R_IN CA55 0.0022 VIN2 TNF1 MPEG Audio L - in PL_L_IN CA56 0.0022...
  • Page 83 CONFIDENTIAL APRXJ *EK51 APTXJ SH-04H RXD_CT TXD_CT *RK35 *QKA2 SRC1202EF AP5VJ 1005 *RKA9 IK01 DS14C232CM 1005 *RKA8 *RKA6 XK25 1005 *IKA1 IK21 GND1 6.00MH SN74LVC1G125DCK RRX6000-0702L CSTCR_G CK22 Dout1 1005 VSS1 /RST *QKA3 1.0/6.3 SRC1202EF Rin1 1005 OSC1 PTA0 *RKA7 Rout1 OSC2 PTA1...
  • Page 84 CONFIDENTIAL USBCANT *IP01 *IP01 *IP01 MD2408A MD2408A MD2408A PERIPHERALS MEMORY DISPLAY *RP72 *RP41 CHPPXE *RP31 *RP42 NPCS1 NWD_OVF CHPNWD PFCS MA14 MA14 PXOE PCLKO GCLK *RP01 *RP43 1005 1005 NPCS0 PFCS MA13 MA13 VBLK *RP21 *RP44 2010 1005 SPCK SDCS SDCS MA12 MA12...
  • Page 85 CONFIDENTIAL SDCS SDCS SDCLK SDCLK DGMU DGMU DGML DGML MD10 MA10 PFCS MD10 MA10 PFCS MD11 MA11 MA15 MD11 MA11 MA15 MD12 MA12 MA16 MD12 MA12 MA16 MD13 MA13 MA17 MD13 MA13 MA17 MD14 MA14 MA18 MD14 MA14 MA18 MD15 MA15 MD15 MA15...
  • Page 86 MEMO...
  • Page 87 ED-X20EF (M1-20ED) Basic circuit diagram list PWB assembly REMOTE PWB assembly MAIN 6 PWB assembly INPUT PWB assembly MAIN 7 POWER UNIT BALLAST 1 PWB assembly MAIN 8 POWER UNIT BALLAST 2 PWB assembly MAIN 9 POWER UNIT CIRCUIT PWB assembly MAIN 10...
  • Page 88 ED-X20EF YK No.0580E QR70821 Printed in Japan (JE)

This manual is also suitable for:

M1-20ed

Table of Contents