Table of Contents
Quick Links
Variable Speed Pool Pump with Bluetooth
Installation and Operating Instructions
Model: SP200BTP
WARNING: Failure to follow these instructions and comply with all
applicable codes may cause serious bodily injury and/or property damage.
This pump requires professional expertise for installation and
maintenance. The installation of this product should be carried out by a
person knowledgeable in swimming pool plumbing requirements and
who follows the installation instructions provided in this manual.
Please pass these instructions on to the operator of this equipment.
Table of Contents
Related Manuals for Davey SILENSOR PRO SP200BTP
Summary of Contents for Davey SILENSOR PRO SP200BTP
- Page 1 Variable Speed Pool Pump with Bluetooth Installation and Operating Instructions Model: SP200BTP WARNING: Failure to follow these instructions and comply with all applicable codes may cause serious bodily injury and/or property damage. This pump requires professional expertise for installation and maintenance.
- Page 2 Read these instructions in their entirety before switching on this pump. If you are uncertain as to any of these installation and operating instructions please contact your Davey dealer or the appropriate Davey office as listed on the back of this document.
- Page 3 If you are using low flow settings on the SilensorPro pump (e.g. Speed 1 - 4), Davey recommends that you check the compatibility of the speed or minimum flow rate required to run specific pool equipment such as: •...
- Page 4 Avoid long extension leads as they can cause substantial voltage drop and operating problems. • Although the Davey electric motor is specifically engineered to perform on a range of power supply voltages, malfunctions or failure caused by adverse voltage supply conditions are not covered under guarantee.
-
Page 5: Guidelines For Recommended Pump Operating Hours
This SilensorPro pool pump incorporates motor overload detection designed to protect the motor from overheating. If the motor gets too hot during operation, its operating speed will reduce to bring it within an acceptable operating temperature and then will speed up to the originally set speed. To reset the motor, switch the power off for 30 seconds, and then return the power from the mains switch. -
Page 6: Technical Specifications
Using your SilensorPro VSD pump with a Davey Salt Water Chlorinator Davey ChloroMatic and EcoSalt salt water chlorinators require a minimum flow rate of 21 gallons per minute (80 lpm) through the chlorinator cell for best efficiency and cell life. Please refer to the performance graph below as a reference for the flow in your pool and refer to the pressure indicated by the gauge on the media or cartridge filter. -
Page 7: Weather Protection
Dimensions DIMENSIONS (inches) Mounting Inlet/ Net Weight Holes Outlet Model (lbs) Diameter SP200BTP 26.3 12.6 13.7 2.55 9.05 14.96 7.87 9.84 1½” / 2” 30.8 Installation of the SilensorPro VSD Pool pump with Bluetooth Location The pump should be located as close to the water as practicable and mounted on a firm base in a well-drained position, high enough to prevent any flooding. - Page 8 Davey Water Products recommends that all installations are fitted with earth leakage or residual current protection devices. CAUTION: In the interest of safety, we advise that all brands and types of pool pumps must be installed in accordance with AS3000 wiring rules or equivalent.
-
Page 9: Pipe Connection
Pipe Connection Barrel unions are provided for connecting to the piping from the pool. The pumps are designed to accept 1½” / 2” (40mm/50mm) PVC fittings. When plumbing the discharge pipe, ensure that the pipework does not interfere with the pumps speed dial. The use of any pipe smaller than those specified above is not recommended. - Page 10 Prior to using this pump you must ensure that: Checklist • Speed (including priming and backwash) setting chosen is a compatible setting with other pool equipment • The pump is installed in a safe and dry environment • The pump enclosure has adequate drainage in the event of leakage •...
-
Page 11: Low Energy Operation
Low Energy Operation: Your SilensorPro VSD Pool Pump has variable speed settings: Model Lowest Speed Highest Speed Backwash Speed SP200BTP Setting 1 – 1500 rpm Setting 10 – 3600 rpm Variable • Speed 1 provides the lowest speed and therefore the greatest energy efficiency and savings. - Page 12 SP200BTP - Performance...
-
Page 13: Features & Functionality
Features & Functionality Your Davey SilensorPro VSD Pool Pump has several operational features: • Multi-Colored LED indicator light Used for identifying required settings for programming time for full speed (Boost) cycling and warnings: > Solid Green = Normal Dial Operation >... -
Page 14: Bluetooth App Setup
- 1. Open the “App Store” app that is available on your device. - 2. Search “Davey Pool Pump” - 3. Install the app on your device The app can be installed on to as many devices as desired, however, only one device can control the pump at any given time. -
Page 15: Schedule Mode
Two modes are available, depending on whether you wish to manually operate the pump or alternatively you can create a schedule of operation. • Manual Mode - If in schedule mode, press “switch to manual mode” - The app will now be in manual mode and you can manually adjust the speed by pressing the (+/-) SilensorPro VSD200 buttons. -
Page 16: Setting A Schedule
The “Weekly cycle” option can be set for the entire week, giving you the ability to alter daily pump cycles depending on weather, bather load etc. Select if you would like the daily cycle or the weekly cycle. Setting a Schedule - Select the box which relates to the time that you require the pump to operate. -
Page 17: Priming Speed / Max Speed
Priming Speed / Max Speed Each time your pump starts it will go through 2 minutes of priming to ensure there is water in the system. You can adjust the speed in which it does this between 5 & 10. The speed you set will limit the maximum speed the pump will run in manual or schedule mode. -
Page 18: Pump Fault Finding
Pump Fault Finding In the instance that there is a fault, the following screen will appear, with text description below the fault indicating how to remedy. SilensorPro VSD200 Fault Title Fault Description Check that the motor is able to rotate freely. Unplug for 1 minute and plug back in to reset, if Pump Fault - Overcurrent problem persists, contact your nearest dealer. -
Page 19: Operating Your Suction Pool Cleaner
Operating your Suction Pool Cleaner Before installing or purchasing a pool cleaner for use with your SilensorPro pool pump, it is important to know the minimum flow rates required for it to operate effectively: To operate a suction pool cleaner with your SilensorPro VSD pump 1. -
Page 20: Troubleshooting
4. Empty the trapped refuse from the basket. Hose out with water if necessary. NOTE: NEVER knock the plastic basket on a hard surface as it will cause damage. 5. Check the strainer basket for cracks, replace the basket in the pump if OK. 6. -
Page 21: Water Quality
If the pump does not operate, the following conditions may apply: 1. The power is not connected. For 240 volts only, check the power point by plugging in a portable appliance to ensure power is available. Also check fuses and the main power supply switch 2. - Page 22 NOTES...
- Page 23 NOTES...
- Page 24 Fax: +971 6 5730472 Fax: 1300 369 119 Email: [email protected] Email: [email protected] Email: [email protected] Website: daveyeurope.eu Website: daveyuae.com Website: davey.com.au P/N 403277 ® Davey is a trademark of Davey Water Products Pty Ltd. © Davey Water Products Pty Ltd 2018.