Page 4
Components identified by shading and ! marked on the schematic diagrams and parts list are critical to safe operation. Replace these components with SONY parts whose part numbers appear as shown in this manual or in supplements published by SONY.
· White Balance Check Note: If the micro processor IC in the adjusting remote com- mander is not the new micro processor (UPD7503G-C56- 12), the pages cannot be switched. In this case, replace with the new micro processor (8-759-148-35). FCB-IX47/47P 2-1 (E) FCB-IX470/470P...
Operation 1. Turn on the power of the camera and start up Windows®. 2. Double click the FCB-IX47 Series Control Panel icon. 3. Perform adjustment by dragging the adjustment slider of the re- spective adjustment using mouse. You can also perform adjust- ment by the arrow mark key when you click the adjustment slider with mouse.
Figure 1189 mm Note : Use the non-reflecting and non-glazing vellum paper whose size is more than A0, and make the boundary between white and black to be smoothly flat. FCB-IX47/47P 2-4 (E) FCB-IX470/470P...
As the upper digit of the hexadecimal notation is B (b), and the lower digit is D (d), the intersection “189” of the 1 and 2 in the above table is the decimal notation to be calculated. FCB-IX47/47P 2-6 (E)
When changing the data, copy the formed again. data built in the same model. Note 3: < > : NTSC model (FCB-IX47/470) Note : If copy the data built in the different model, the camcorder [ ] : PAL model (FCB-IX47P/470P) may not operate.
Page 18
Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-1 (Initialized data) FCB-IX47/47P 2-8 (E) FCB-IX470/470P...
Page 19
Flange back adj. ( Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Note 2: NTSC model : FCB-IX47/470 PAL model : FCB-IX47P/470P Fixed data-2 Address...
1) Select page: 0, address: 01, and set data: 01. f=14.187500MHz±68Hz (PAL) 2) Select page: F, address: 49, change the data and set the SYNC level (A) to the specified value. Note 1: NTSC MODEL: FCB-IX47/470 3) Press the PAUSE button of the adjusting remote commander. PAL MODEL: FCB-IX47P/470P 4) Select page: 0, address: 01, and set data: 00.
4) Select page: F, address: 21, set data: 52, and press the PAUSE button of the adjusting remote commander. Before Modify data After Modified data 5) Select page: 0, address: 03, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. FCB-IX47/47P 2-15 (E) FCB-IX470/470P...
4) Select page: 0, address: 03, and set data: 00. 18)Select page: 2, address: 01, and set data: 01, and press the PAUSE button. 19)Select page: F, address: 30, change the data and adjust the DDS display data to “92”. FCB-IX47/47P 2-16 (E) FCB-IX470/470P...
3E to 42, 76 to 7B.) 7) Select page: 2, address: 02, and check that the data is “01”. Processing after Completing Adjustments 1) Turn OFF the main power supply. 2) Perform “Flange Adjustment (2)”. FCB-IX47/47P 2-17 (E) FCB-IX470/470P...
2) Select page: 0, address: 03, and set data: 00. 3) Select page: 2, address: 40, and set data: 00. 4) Select page: 2, address: 41, and set data: 00. 2. Vertical period t=0 ± 0.1mesc Color bar chart picture frame TV monitor picture frame FCB-IX47/47P 2-18 (E) FCB-IX470/470P...
34, 36, F5, F6 Specified Value All color luminance points should settle within each color reproduction frame. (Last page of this manual) Note1: NTSC model:FCB-IX47/470 PAL model: FCB-IX47P/470P Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Burst position 2) Select page: 2, address: 01, set data: 3D, and press the PAUSE button of the adjusting remote commander.
' - 14 ........... Equation 4 15) Convert D ' to hexadecimal notation, and obtain D 16) Select page: F, address: 3D, set data: D , and press the PAUSE button of the adjusting remote commander. FCB-IX47/47P 2-20 (E) FCB-IX470/470P...
2) Select page: 0, address: 01, and set data: 00. 3) Select page: 2, address: 01, and set data: 00, and press the PAUSE button of the adjusting remote commander. 4) Select page: 0, address: 03, and set data: 00. FCB-IX47/47P 2-22 (E) FCB-IX470/470P...
Page 33
2 mm 2 mm Figure A 1.0 mm 3 mm 1.0 mm 3 mm Figure B 3 mm 2.0 mm 3 mm 1.0 mm Figure C FCB-IX47/47P 2-23 (E) FCB-IX470/470P...
Therefore, specified parts should be used in the case of replacement. (2) Standardization of Parts Repair parts supplied from Sony Parts Center may not be always identical with the parts which actually in use due to “accommodating the improved parts and/or engineering changes”...
COMP INV IN2 ENCODE LINE IN2(Y) TITLE PB/EE INSERT MUTE CLAMP DAMMY SYNC EE IN VREG V REG COMP INV IN1 TITLE LINE IN1(Y) INSERT MUTE COMP OUT1 CLAMP DAMMY SYNC TITLE GND2 GND1 INSERT Y INV IN1 MUTE IC602 FCB-IX47/47P FCB-IX470/470P...
Page 46
BLOCK DIAGRAM CAMERA CONTROL BLOCK (1/2) VC–211 BOARD (2/3) IC602 CN601 1.7Vp-p 20 MHz IC602 3.2V 3Vp-p 13µsec IC602 IC402 CN401 IC402 IC402 IC402 XCS PDR IC401 MODE CONTROL 3.2V VC SO XVC SCK IC601 XRST SYSTEM MEM VDI FCB-IX47/47P FCB-IX470/470P...
Page 47
PDR CS –2B DIR2B XVC SCK XVC SCK For FCB-IX470/IX470P VC SO CAMERA VC SO CN704 LANC CONTROL CKIN 4.9V 3.2V 3.2V XRST SYSTEM XRST X CLR UNREG UNREG SYSTEM LANC OUT LANC OUT LANC IN LANC IN FCB-IX47/47P FCB-IX470/470P...