Table of Contents
Quick Links
Table of Contents
Related Manuals for Honeywell NOTIFIER LCD6000T
Summary of Contents for Honeywell NOTIFIER LCD6000T
- Page 1 LCD6000T Programming And installation Repeater Panel manual...
- Page 2 INDEX GENERAL DESCRIPTION OPERATION TECHNICAL SPECIFICATION SIZE FOR WALL ASSEMBLY CONTROLS ON THE FRONT PANEL SIGNALLINGS ON THE FRONY PANEL USER INTERFACE DESCRIPTION CONDITION WITH ALARM ZONE EVENT CONDITION WITH BREAKDOWN ZONE EVENTS CONDITION WITH SYSTEM BREAKDOWN EVENT DISPLAY OF EXCLUDED ZONES AND POINTS SENSOR ZONES TEST...
- Page 3 NOTE: Do not try to install the LCD-6000T panel without reading this manual. ATTENTION: This manual refers to all functions available in the software revision indicated on the cover. DETECTION SYSTEM LIMITS An alarm or fire detection system can be very useful for the prompt warning of any dangerous event, such as a fire, a robbery or a simple burglary, in some cases it can automatically manage events (transmission of messages for room evacuation, automatic fire-extinguishing, TVCC system interface, access route or door blockage, automatic warning to authorities, etc.), but in any case, it does not ensure protection against...
-
Page 4: General Description
This device must be installed and must operate in accordance with these instructions and with the rules in force in the installation place. GENERAL DESCRIPTION DESCRIPTION LCD-6000T is a panel for the management of gas detection devices or T echnological devices having a 4-20mA interface which are installed in AM-2000;... -
Page 5: Installation
INSTALLATION Sizes for wall assembly The panel can be wall- installed through 4 self- blocking cleats (masonry walls) or self-tapping screws (prefabricated panels, etc.) The screws used must have a maximum diameter of 5 mm. It is recommended not to install the panel near heat sources (radiators, etc.) Connect the incoming cable to CN1 extractable terminal block Fasten the incoming... -
Page 6: Controls On The Front Panel
CONTROLS ON THE FRONT PANEL MENU BUZZER SILENCING : by pressing this key the user can access both : by pressing this key, you can silence the LCD6000T panel buzzer and you can the LDC6000T panel programming menu and the display functions of the excluded points and zones. - Page 7 BREAKDOWN (Yellow): It flashes if there is any type of breakdown and it has not been recognized. It is permanently lit if all breakdowns have been recognized VOLTAGE (Green): It is permanently lit if the LCD6000 T Panel is powered Exclusion (Yellow): 1.
-
Page 8: Normal Condition
N.B. LCD-6000T is a panel for the management of installed Technological devices having 4-20mA (MMT or IIG4-N) interface. The technologica l point programming must be perf ormed on the control unit ( refer t o c hapter Programming of MMT and IIG4-Ntechnological devices contained in this manual). Normal condition The following is displayed when there are no anomaly conditions (alarms or breakdowns) on the LCD6000T panel:... - Page 9 The following is displayed when there is an alarm zone in the control unit. Display Area of the first event First alarm zone Alarm zone counter Text programmed for the zone Date and time of the first event of zone alarm Latest alarm zone Date and time of the latest zone...
- Page 10 Condition with breakdown zone events The following is displayed when the control unit is in breakdown zone condition The breakdown events are also initially displayed for zone Date and time Breakdown zone of the first counter zone breakdown event Date and time of the latest alarm zone Display area of event...
- Page 11 Condition with System breakdown event The following is displayed when there is a system anomalous condition at the control unit. Date and time of the event System breakdown Description of the counter System Breakdown Acknowledge Outputs NB: This function is enabled only for the AM4000G For acknowledge outputs activated on alarm see the following procedure 1.
- Page 12 enter the level 2 password After entering the password to display the following 5. Press the key to confirm. Display of excluded zones and points To access the display functions of the excluded zones or points follow these instructions: 6. Press the key to display the following 7.
- Page 13 It indicates the displayed It indicates the Excluded point Exclusion event number total number Point indication Name assigned to the point Use the arrow keys to Name of the scroll the excluded point list zone assigned to the point Press the key return to the previous menu Zones...
-
Page 14: Local Programming
TEST From the Main Menu through the arrow keys select the item “TEST” and press the key to access the display menu of the test zone devices. The following menu is displayed: Number counter of devices under test Number Counter of zone under test To display the lists of the devices under Test (Sensors or Zones) select through the arrow keys ... -
Page 15: Buzzer Volume
Where: Address Select the item “Address” to assign the peripheral number to the LCD-6000T terminal device. Use the arrow keys to select the peripheral number and press the Lists key to confirm the datum. The useful LCD-6000T are from 1 ÷ 16 addresses to be assigned to the The address assigned to the terminal device is unique, therefore it is not possible to have several terminals with the same address. -
Page 16: Rs.485 Serial Line
RS.485 serial Line The LDC6000 panel is connected to the control unit through the RS.485 serial line. The RS.485 line must be installed in “MULTI-POINT” configuration (daisy chain). Each peripheral must be programmed with an address from 1 16. Refer to the installation manuals of each peripheral. Installation in “Multi-Point”... - Page 17 Installation in “Multi-Point” configuration (Daisy Chain) Shared Power – Connect two wires from the RS.485 +24V terminals of the control unit (LIN+ LIN- terminals) EOL= 120 correspondent terminals of the first EOL= 120 device on the line. Continue the wiring from the first device to the subsequent one, and so on.
- Page 18 Screened cable and earth connection During installation, consequences of the connection of remote earth references must be Schermo: Connettere al considered telaio con un anello M5 e vite When connections between Utilizzare la RS.485 circuits, are performed if an Schermo: posizione sul collegare...
-
Page 19: Electrical Features
CN1 Terminal block Description Features Notes NOT USED NOT USED RS 485 serial line LIN – Reference negative for RS 485 serial line RS 485 serial line LIN + Power supply input + 24Vcc ELECTRICAL FEATURES Operating temperature: - 5° C - + 40° C. Relative humidity: 10 % - 93 % (with no condensation). - Page 20 The following pages are related to the programming of sensor technology for the following panels: AM-2000N AM-4000 AM-6000N PAGE - 18 Installation manual LCD6000 NOTIFIER ITALIA Doc. M-184.1-LCD6000T-ENG Rev A.2 LCD6000_manu...
- Page 21 Programming of the MMT and IIG4-N technological devices on the control units AM-2000; AM-4000; AM-6000 The AM series control unit through the LCD-6000T panel manages the new series of 4-20mA MMT and IIG4-N modules. All anomaly, pre-alarm and alarm signallings coming from 4-20mA devices will be managed only by the LCD-6000T panel These new devices occupy just one address for device on the analogue line.
- Page 22 Threshold inversion option (default =NO) ALARM 20mA PRE-AL1 The diagram in the figure shows the operation feature of a “TEC3” device programmed with threshold inversion option = NO. As you can see the operation feature is to increase the current values.
- Page 23 The type-id “TEC2” operation feature is the following: Highest value of the scale (refer to chapter Technological Ranges). Lower threshold programmable by the user (40 % of the selected highest value of the scale). Upper threshold programmable by the user (60 % of the selected highest value of the scale) ...
- Page 24 Technological device programming through Type- ID “TEC3” or “TEC2”. The technological device programming is performed on the control unit From the Programming\|Points menu by selecting the item “SENSORS” and by confirming this selection through the enter key you can enter the sensor complete programming procedure. This procedure is made up of 4 programming folders (to access the folders, use the arrow keys ) and to enter data consult the editing function previously described in the keyboard operation to enter data paragraph (AM Serie-manu- prg-ENG.pdf)
- Page 25 Tracking option By selecting “NO” in the function “Led Blink” the flashing of the led on the module during the line query is disabled. This function can be useful in such environment as hospitals, hotels, etc. Range = Configuration of highest value of the scale (refer to Technological Range table) Attention: do not change the default datum of the relative sensitivity...
- Page 26 Sensor address CBE equation (usable to activate the generic groups). Associated zone number By selecting “NO” in the “Led Blink” function the flashing of led on the module is disabled during the line query. Tracking option This function can be useful in such environment as hospitals, hotels, etc.
- Page 27 … … It can be used if the points have consecutive addresses and have common parameters. The function “Remove From … to” enables to eliminate from the control unit programming an entire consecutive block points, by inserting the start and end addresses. The procedure to perform the block programming is the following: ...
- Page 28 Technological ranges. The Technological Range programming is performed on the control units From the Programming menu by selecting the item “TECHNOLOGICAL RA NGES” you enter the programming procedure where it is possible to configure a maximum number of 16 ranges whose first seven are by default as it is shown in the following table.
- Page 29 Second folder or interval folder (Prog. of Lowest value of the scale, highest value of the scale) Programming of the lowest value of the scale Enter the value indicated on the plate values of the technological device Programming of the highest value of the Scale.
- Page 30 E-mail: [email protected] A Honeywell company Every care has been taken in the preparation of this data sheet but no liability can be accepted for the use of the information therein. Design features may be changed or amended without prior notice.