Related Manuals for Samsung VR30T80 Series
Summary of Contents for Samsung VR30T80 Series
- Page 1 Jet Bot User manual VR30T80**** series • Before operating this unit, please read the instructions carefully. • For indoor use only...
-
Page 2: Table Of Contents
APPENDIX Safety information SmartThings App Setting up the wireless router INSTALLATION Downloading the SmartThings App Setting up a SAMSUNG account Installing a Docking Station Registering a device to the SmartThings App 30 OPERATION Software Update Functions of the SmartThings App... -
Page 3: Preparation
PREPARATION Accessories Accessories may differ depending on the models. Docking Station Pre-motor Filter: 2 units Spin Brush: 2 units (Inside the product: 1 unit, (Inside the product: 1 unit, Spare: 1 unit) Spare: 1 unit) Battery Charger/Power cord Boundary Markers User Manual Safety information • Before operating the appliance, please read this manual thoroughly and retain it for your reference. - Page 4 State of California Proposition 65 Warning (US only) WARNING This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For battery recycling go to call2recycle.org or call 1-800-822-8837 L i - i o n Failure to meet these requirements could cause damage to the internal parts of the vacuum and void your warranty.
- Page 5 • Do not operate the vacuum in an area where there are lit candles or fragile objects on the floor. • Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit or bump into. •...
- Page 6 Jet Bot • Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc. • Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on.
- Page 7 Power related WARNING • Please prevent any risk of electric shock or fire. – Do not damage the power cord. – Do not pull the power cord too hard or touch the power plug with wet hands. – Do not use a power source other than 100-240 V ~ 50-60 Hz and also do not use a multi-outlet to supply power to a number of devices at the same time.
- Page 8 • Attach the Boundary Markers to a place where the Jet Bot may fall such as a stair or a banister to prevent product damage and injury. – Please keep the Cliff Sensor clean all the time for safety. • Be sure the Jet Bot does not suck in or touch any kind of liquids (water, beverage, filth, etc.).
- Page 9 • Do not use the Jet Bot on black colored floors. – The Jet Bot may not be able to operate normally. • Do not place any objects within 0.5 m of either side of the Docking Station or within 1 m of the front of the Docking Station. •...
- Page 10 In use WARNING • If any abnormal sounds, smells or smoke come from the Jet Bot, immediately shut off the power switch of the Jet Bot and contact a service center. CAUTION • Using the Jet Bot on a thick carpet may damage both the Jet Bot and the carpet.
- Page 11 • When the power cord is damaged, contact a service center to get it replaced by a certified repairman. – There is a risk of fire or electric shock. • Please check with a SAMSUNG Electronics service center when replacing batteries. – Using batteries from other products can cause malfunction.
- Page 12 • Be careful that the LiDAR sensor is not exposed to a direct light such as sun light, infrared light, etc. – The direct light can affect the performance of the LiDAR sensor. • When carrying the Jet Bot, be careful not to let it drop. –...
- Page 13 REGULATORY NOTICE 1. FCC Notice WARNING • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received including interference...
- Page 14 FCC RADIATION EXPOSURE STATEMENT: • This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
-
Page 15: Installation
INSTALLATION Installing a Docking Station Approximately 0.5 m Approximately Approximately 0.5 m 1 Connect the provided Battery Charger jack 2 Position the Battery Charger cord into the to the rear of the Docking Station. fixing groove at the rear of the Docking Station. -
Page 16: Operation
OPERATION Charging the Jet Bot Before using the Jet Bot for the first time, charge it completely. (For the charging time and cleaning time, refer to the ‘Product specification’.) 1 Open the upper cover of the Jet Bot and remove the white gasket. 2 Remove the yellow gasket attached to the power switch at the side of the Jet Bot and press the power switch to turn the Jet Bot... - Page 17 Auto charging The Jet Bot automatically returns to the Docking Station when it completes cleaning, when the Dustbin is full, or when the battery is low to recharge. Docking (Recharging) You can return the Jet Bot to the Docking Station while cleaning to recharge. •...
- Page 18 Checking if the docking (recharging) does not work Check the Docking Station’s installation Charge the Jet Bot manually for the following status. conditions. • Check whether the Docking Station has • When the Docking Station is installed in a been installed in a place where the Docking corner Station cannot guide the Jet Bot to return.
-
Page 19: Operation
OPERATION Using the Jet Bot Before using the Jet Bot, press the power switch at the side of the Jet Bot to turn the Jet Bot ❇ For the normal use of the Jet Bot’s functions, the SmartThings connection is required. –... -
Page 20: Operation Status On The Led Status Indicator
Operation status on the LED Status Indicator Classification Color Meaning Blinking without An error occurs. moving While Blinking while Auto returning to the Docking Station due to low battery operating moving Operating stops due to low Jet Bot battery Red, orange, or yellow (depending While charging on charging progress) While... -
Page 21: Cleaning Functions
Cleaning Functions Cleaning Functions Operation • Auto Clean: Cleans automatically until the Jet Bot completes cleaning all rooms one time. Cleaning Methods • Room Clean: You can select a room you want to clean. • Spot Clean: You can set a specific area you want to clean. •... -
Page 22: Additional Functions
Additional functions Additional functions Operation • When charging is complete, the Jet Bot automatically enters the Sleep Mode. While the Jet Bot is docked on the Docking Station, press and hold the [ ] for 7 seconds to set it to the Sleep Mode. To cancel the Sleep Mode, start cleaning or press the [ ] for Energy-Saving... -
Page 23: Attaching Boundary Markers
Attaching Boundary Markers If Boundary Markers are attached before using the Jet Bot, the Jet Bot can operate safely. You can purchase additional Boundary Markers at a service center. To prevent the Jet Bot from entering the following areas, attach the Boundary Markers to the floor in a shape with 15 cm space distance. -
Page 24: Parts Diagram
Parts diagram Jet Bot 01 Obstacle Sensor 02 Power switch 03 LiDAR Sensor 04 Dustbin 05 Start/stop button 06 Docking (Recharging) button 07 Status Indicator 08 Docking Sensor Window 09 Upper Cover Bottom 01 Charging Pin 02 Brush 03 Brush Cover 04 Cliff Sensor 05 Roller 06 Battery Cover... -
Page 25: Maintenance
MAINTENANCE Cleaning the Jet Bot Before maintenance work, you should turn off the power switch at the side of the Jet Bot. Emptying and cleaning the Dustbin 1 Grasp the Jet Bot’s cover at the groove 2 Hold the Dustbin handle and lift the and lift it up. -
Page 26: Cleaning The Brush
Cleaning the brush 1 Push the Brush Cover Lock to the right 2 Detach the brush cover. to unlock. 3 Lift up the left side of the brush first and 4 Clean the brush. then pull the brush from the groove on the right. -
Page 27: Cleaning The Sensor Window
Cleaning the Sensor Window Wipe the Sensor Window with a soft cloth. Docking Sensor Obstacle Cliff Sensor Window Sensor LiDAR Sensor Dust Sensor Rear Sensor Cleaning the Driving Wheel 1 Place a soft cloth down first, turn the Jet 2 Remove foreign matter with a blunt rod or Bot over, and place it gently on the cloth. -
Page 28: Cleaning The Spin Brush
Cleaning the Spin Brush Cover the Spin Brush with a hot steamed cloth When the Spin Brush is very tangled with for 10 seconds, then wipe the Spin Brush. hair, threads, etc., detach the Spin Brush with a screwdriver while gripping the Spin Brush, and remove the foreign matter. -
Page 29: Appendix
• SAMSUNG Jet Bot supports IEEE 802.11b/g/n and Soft-AP. – IEEE 802.11n is recommended. • SAMSUNG Jet Bot supports only DHCP (Dynamic Host Configuration Protocol). Please make sure that the DHCP server option is activated on your wireless router. • The Jet Bot supports the WEP-OPEN, WPA-PSK/TKIP, and WPA2-PSK/AES for the authentication and encryption protocols. -
Page 30: Downloading The Smartthings App
• To set up a SAMSUNG account, you can follow the directions provided by the SmartThings App. • Or, if you have a SAMSUNG smartphone, you can add your SAMSUNG account in the setting app of your smartphone. Then, it will automatically sign in to your SAMSUNG account and you can use the SmartThings App. -
Page 31: Software Update
3 If a pop-up saying that a new device has been found appears, tap ADD NOW. – If the pop-up does not appear, add a device by selecting the ‘Home appliances’ category → ‘Robot cleaner’ and the Jet Bot to connect. –... -
Page 32: Functions Of The Smartthings App
Functions of the SmartThings App Classification Functions Explanation • You can check the result of the last cleaning. Monitoring Cleaning Report • You can check the histories of last 50 cleanings. • You can stop cleaning and have the Jet Bot Dock return to the Docking Station. - Page 33 Classification Functions Explanation • When cleaning is complete, you can receive Cleaning completed cleaning completion notice. Notice • If the Jet Bot needs to be checked, you can Check Notice receive a notice. • You can set a zone where you do not want the Jet Bot to clean.
-
Page 34: Notes And Cautions
Notes and cautions Installation NOTE • Install the Docking Station in a place where the floor and wall are level. • If the cleaning area is wooden floors, it is best to install the Docking Station along the grain of wooden floors. •... -
Page 35: Using
• If the Jet Bot is left detached from the Docking Station, the battery will drain naturally. – Try to keep the Jet Bot being charged on the Docking Station. (However, turn off the power switch and leave the Docking Station unplugged when planning to leave the house for long periods of time by going on a business trip or vacation, etc.) Using... -
Page 36: Cleaning And Maintenance
• If it is difficult to remove foreign matter from the brush, contact an authorized SAMSUNG service center. • Since the brush sweeps dirt up from the floor during cleaning, foreign matter such as a thin and long thread, long hair, etc. may get caught in it. -
Page 37: Battery Usage
• This battery is exclusively for the SAMSUNG Electronics Jet Bot. Do not use it for any other products or purposes. • Do not disassemble or modify the battery. -
Page 38: Corrective Measures Before Reporting A Problem
Corrective measures before reporting a problem 1 The Status Indicator 2 Turn off the power 3 When turning turns red and blinks switch and check the the Jet Bot on by with a voice guide. instructions below pressing the power and take appropriate switch, the Status actions. -
Page 39: Troubleshooting
Troubleshooting Symptom Checklist • Check if the power switch is on. • Check if the Status Indicator is on. • Check if the Jet Bot's battery is depleted. – When the Jet Bot’s Status Indicator turns red and stays red, place the Jet Bot manually on the Docking The Jet Bot is not working at all. - Page 40 Symptom Checklist The Jet Bot does not detect the • Make sure the Boundary Markers are attached as ( Boundary Marker and crosses shape at 15 cm before the locations where the Jet Bot the boundary. should not cross. • Check if the Docking Station is installed along the grain of wooden floors or tiles.
- Page 41 • Connect the Jet Bot to a wireless router by referring to App, but the Jet Bot fails to be the ‘SmartThings App’ of the user manual. connected. I fail to log into the SAMSUNG • Check your ID and password on the screen of the account. SAMSUNG account.
- Page 42 SmartThings App". • When the product registration fails repeatedly, restart the SmartThings App and try the product registration. • All users should use the SAMSUNG account issued by the country which launches the product. (Applicable to iOS only) During product registration, the AP •...
- Page 43 Symptom Checklist • If the Jet Bot is distant from a wireless router, connection cut may occur. • Close the SmartThings App and restart the App. The ‘Offline’ message of the Jet • If the connection cut occurs repeatedly, try the product Bot appears on the SmartThings registration again.
-
Page 44: Open Source Announcement
The software included in this product contains open source software. To obtain the source code covered under licenses which have the obligation of publishing source code (e.g. GPL, LGPL… etc), please visit http://opensource.samsung.com/ and search by model name. It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM;... -
Page 45: Product Specification
Product Specification Classification Items VR30T80**** series Weight 3.4 kg Mechanical LiDAR location recognition Cleaning method specifications Button method of the Jet Bot Touch type Power consumption of the 60 W (Spot Clean) Electrical Jet Bot specifications Battery specification Lithium-ion 21.9 V / 52.56 Wh Charging type Auto charging / Manual charging Auto Clean, Room Clean, Spot Clean... - Page 46 If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Country Customer Care Center Web Site 1-800-SAMSUNG (726-7864) www.samsung.com/ca/support (English) CANADA 1-844-SAM-PAYS (726-7297) www.samsung.com/ca_fr/support (French) 1-800-SAMSUNG (726-7864) U.S.A www.samsung.com/us/support 1-844-SAM-PAYS (726-7297)