Quick Links
User Manual
802.11bgn WLAN MODULE
MODEL DWM-W069
The purpose of this manual is to explain correct way how to integrate module
DWM-W069 to the end product. It includes procedures that shall assist you to avoid
unforeseen problems. This manual presents information that shows how module
and OEM product, where module integrated, complies with regulations in certain
regions. Any modifications, not expressly approved by the manufacturer could void
the authority to operate in these regions.
The 802.11bgn WLAN MODULE, model DWM-W069 has to be installed and used
in accordance with the technical description/installation instructions provided by the
manufacturer.
For detail information concerning type approval of this module (e.g. where this
module is already pre-approved) please contact the authorized local distributor or
the manufacturer.
The system may only be implemented in the configuration that was authorized.
Note that any changes or modifications to this equipment not expressly approved
by the manufacturer could void the user's authority to operate this equipment.
Summary of Contents for Sony DWM-W069
- Page 1 MODEL DWM-W069 The purpose of this manual is to explain correct way how to integrate module DWM-W069 to the end product. It includes procedures that shall assist you to avoid unforeseen problems. This manual presents information that shows how module and OEM product, where module integrated, complies with regulations in certain regions.
-
Page 2: Regulatory Information
Regulatory Information Operational Information Wireless Interoperability The end product integrating this module is designed to be interoperable with any wireless LAN product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency division multiplexing (OFDM) radio technology and to comply with the following standards. - Page 3 Labeling MITSUMI WiFi MODULE DWM-W069 labelled as below. FCC ID: EW4DWMW069 The label with FCC ID is to be placed on the module. If FCC ID is not visible when the module is installed into the system, “Contains FCC ID: EW4DWMW069”...
- Page 4 Labeling MITSUMI WiFi MODULE DWM-W069 labelled as below. IC: 4250A-DWMW069 The label with IC ID is to be placed on the module. If IC ID is not visible when the module is installed into the system, “Contains IC: 4250A-DWMW069”...
- Page 5 Caution: Exposure to Radio Frequency Radiation. To comply with IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
- Page 6 Europe-EU Declaration of Conformity and Restrictions Hereby, MITSUMI declares that this Mitsumi 802.11bgn WLAN MODULE DWM-W069 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment is marked with the symbol and can be used throughout the European community.
- Page 7 To comply with RF exposure compliance requirements, a separation distance of at least 2.2 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter, without further RF Exposure evaluation.
- Page 8 NCC Warning Statement 低功率電波輻性電機管理辦法 第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使 用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發 現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信 或工業、科學及醫療用電波輻射性電機設備之干擾。 模組認證合格標簽 (ID): “ CCXXxxLPyyyZz＂ 如果使用本模組之平台,無法在外部看見審驗合格標籤時,應在該 平台的外部明顯標示 “內含射頻模 CCXXxxLPyyyZz” . Translation: Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery.
- Page 9 Information for OEM integrator Label for end product must include is " Contains XXXyyyLPDzzzz-x¨...