1. Manuals
  2. Brands
  3. Epson Manuals
  4. Controller
  5. S1D16000 Series
  6. Technical manual

Epson S1D16000 Series Technical Manual

Lcd drivers
Hide thumbs
Table of Contents

Quick Links

MF425 - 05
LCD DRIVERS
IEEE1394 Controller
S1D16000 Series
S1R76801F00A
Technical Manual
Technical Manual
Table of Contents
loading

Related Manuals for Epson S1D16000 Series

Summary of Contents for Epson S1D16000 Series

  • Page 1 MF425 - 05 IEEE1394 Controller LCD DRIVERS S1R76801F00A S1D16000 Series Technical Manual Technical Manual...
  • Page 2 Seiko Epson. Seiko Epson reserves the right to make changes to this material without notics. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no repersesnation that this material is applicable to products requiring high level reliability, such as, medical products.
  • Page 3 The information of the product number change Starting April 1, 2001 the product number will be changed as listed below. To order from April 1, 2001 please use the new product number. For further information, please contact Epson sales representative.
  • Page 4 CONTENTS S1D 16000 series Selection Guide S1D 16006 ............1-1 S1D 16400 ............2-1 S1D 16501 ............3-1 S1D 16700 ............4-1 S1D 16702 ............5-1 www.DataSheet4U.com...
  • Page 5 Selection Guide www.DataSheet4U.com...
  • Page 6 S1D16000 (SED1600) series Segment drivers Supply voltage LCD voltage Part number Duty Data bus Package Outputs range (V) range (V) S1D16006D00A Al pad chip (for COB) (SED1606D S1D16006D00B Au bump chip (SED1606D S1D16006F00A 2.7 to 5.5 8 to 28 1/100 to 1/300 4-bit parallel QFP5-100pin (SED1606F...
  • Page 7 S1D16006 Series www.DataSheet4U.com Rev.2.1...

  • Page 8: Table Of Contents

    CONTENTS DESCRIPTION ...............................1-1 FEATURES ..............................1-1 BLOCK DIAGRAM ............................1-2 PIN DESCRIPTION ............................1-3 PAD ................................1-4 PIN LAYOUT ..............................1-6 FUNCTIONAL DESCRIPTION ........................1-7 TIMING CHART .............................1-8 ABSOLUTE MAXIMUM RATINGS ......................... 1-9 ELECTRICAL CHARACTERISTICS ......................1-10 LCD DRIVE POWER ............................ 1-13 TYPICAL CIRCUIT DIAGRAM ........................

  • Page 9: Description

    • Non-bias display off function • Chip packaging S1D16006D00A (AL-pad die form) S1D16006D00B (Au bump die form) S1D16006D01A (AL-pad die form) S1D16006D01B (Au bump die form) PKG S1D16006F00A (QFP5-100 pin) • No radial rays countermeasure taken in designing www.DataSheet4U.com EPSON Rev.2.1 1–1...

  • Page 10: Block Diagram

    LCD driver 80 bit Level shifter 80 bit DSPOFF Latch 80 bit Data register 80 bit D3 to D0 XSCL Enable shift register EIO2 EIO1 *1 Dummy terminal NC when S1D16006D00 is used. www.DataSheet4U.com DSPOFF terminal when S1D16006D01 is used EPSON 1–2 Rev.2.1...

  • Page 11: Pin Description

    When used at a same potential, V and V are used by grounding them close to the IC chip. *1 Be sure to connect V to V to their LCD power, respectively. Total: 100 S1D16006D00 (including four NC’4) S1D16006D01 (including four NC’3) EPSON Rev.2.1 1–3...

  • Page 12: Pad

    0.525 mm (Au-bump die form) www.DataSheet4U.com Au bump specifications [Reference values] 117µm × 109µm ± 20 um Bump size: Bump height: 17µm to 28µm (Details shall be stipulated in the delivery specification.) AL-pad die form Pad Opening 87×76µm EPSON 1–4 Rev.2.1...
  • Page 13 1767 –2611 –885 1921 XSCL –1039 2074 www.DataSheet4U.com –1192 2228 –1346 2381 2622 –1346 –76 EIO1 –2381 –1578 –1188 –230 –1029 –384 *1: Pad No.89 is dummy when S1D16006D00 is used. It will be DSPOFF with S1D16006D01 EPSON Rev.2.1 1–5...

  • Page 14: Pin Layout

    Package Type: QFP–5 100pin S1D16006F INDEX PIN No. NAME PIN No. NAME PIN No. NAME PIN No. NAME PIN No. NAME EIO2 www.DataSheet4U.com XSCL EIO1 *1: Pad No.89 is dummy when S1D16006D00 is used. It will be DSPOFF with S1D16006D01 EPSON 1–6 Rev.2.1...

  • Page 15: Functional Description

    The relationship among the data bus signal, AC converted signal FR and segment output voltage is as shown in the table below: (S1D16006D00 Data bus O output voltage www.DataSheet4U.com signal HIGH HIGH HIGH (S1D16006D01 Data bus DSPOFF O output voltage signal HIGH HIGH HIGH HIGH HIGH — — EPSON Rev.2.1 1–7...

  • Page 16: Timing Chart

    EIO 2 EIO 3 1 to 3 stand for a cascaade No. of driver. LATCH DATA www.DataSheet4U.com DSPOFF S1D16006D00 S1D16006D01 When S1D16006D01 is used: The driver output is forcibly switched to V0 output upon switching of DSPOFF EPSON 1–8 Rev.2.1...

  • Page 17: Absolute Maximum Ratings

    4. Floating of the logic system power during while the LCD drive system power is applied, or exceeding V = –2.6 V can cause permanent damage to the LSI. Functional operation under these conditions is not implied. Care should be taken to the power supply sequence especially in the system power ON or OFF. EPSON Rev.2.1 1–9...

  • Page 18: Electrical Characteristics

    Other conditions are the consumption (2) same as in the item of I Input pin D0 to D3, LP, FR – – Freq.=1MHz capacitance XSCL, SHL Ta=25°C Input/output pin By unit of a chip – – EIO1, EIO2 capacitance EPSON 1–10 Rev.2.1...
  • Page 19 LP is HIGH and XSCL is LOW. *4 t and t of input signal are stipulated by unit of 20 ns. *5 At a high-speed operation, t and t = {t – (t )}/2 EPSON Rev.2.1 1–11...
  • Page 20 CL=100pF (On) FR to SEG output delay time – FRSD *1 t and t of input signal are stipulated by unit of 20 ns. *2 At a high-speed operation, t and t = {t – (t )}/2 EPSON 1–12 Rev.2.1...

  • Page 21: Lcd Drive Power

    Until the LCD driver voltage stabilizes. It is recommended to set the LCD driver output potential to V using the display off function (DSPOFF). Power ON/OFF sequence when S1D16006D01 is used > t1.t2.t3 0 sec Power ON Power OFF DSPOFF EPSON Rev.2.1 1–13...

  • Page 22: Typical Circuit Diagram

    S1D16006 Series 12. TYPICAL CIRCUIT DIAGRAM Configuration Drawing of Large Screen LCD – – – – www.DataSheet4U.com EPSON 1–14 Rev.2.1...
  • Page 23 S1D16400 www.DataSheet4U.com...
  • Page 24 CONTENTS DESCRIPTION ...............................2-1 FEATURES ..............................2-1 BLOCK DIAGRAM ............................2-2 FUNCTIONS OF THE TERMINALS ....................... 2-3 PAD LAYOUT ..............................2-4 PAD CENTER COORDINATES ........................2-5 FUNCTION DESCRIPTIONS ......................... 2-6 ABSOLUTE MAXIMUM RATING ........................2-7 ELECTRICAL CHARACTERISTICS ......................2-8 REGARDING THE LCD DRIVING POWER ....................2-12 AN EXAMPLE OF CONNECTION .......................

  • Page 25: Description

    • Pin selection of the output shift direction is available. • Offset bias regulation of the liquid crystal power is possible depending on the V level. • Logic system power source : –2.7V to –5.5V • Product shapes Chip : S1D16400D00B (Au bump article) www.DataSheet4U.com EPSON 2–1...

  • Page 26: Block Diagram

    S1D16400 Series 3. BLOCK DIAGRAM ······································ LCD driver 80 bit Level shifter 80 bit DSPOFF Latch 80 bit Data register 80 bit D0 to D3 XSCL Inable shift register EIO2 EIO1 www.DataSheet4U.com EPSON 2–2...

  • Page 27: Functions Of The Terminals

    At the LOW level, it forces the output to V0 level. * When using this function, the unit may be used in common with S1D16700 *1 Be sure to connect pairs of V0 - V5 to respective LCD power sources. Total 107 (including NC5) EPSON 2–3...

  • Page 28: Pad Layout

    86µm × 68µm ±4µm Bump size (Pad No. 28 ~ 36 and 99 ~ 107) 82µm × 74µm ±4µm Bump size (Pad No. 38 ~ 97) 22.5 ±5.5µm Bump height A ~ D (Pad No. 1 ~ 107) www.DataSheet4U.com EPSON 2–4...

  • Page 29: Pad Center Coordinates

    1875 –4554 4091 1697 –4733 4594 1518 –4912 4984 1340 –5090 5164 1161 –5269 5345 –5644 EIO1 5644 –544 –426 –320 –215 –109 –4 –4 –89 –109 www.DataSheet4U.com –268 –215 –447 –320 –625 –426 –804 EIO2 –544 –982 EPSON 2–5...

  • Page 30: Function Descriptions

    LCD driver It outputs the LCD drive voltage. Relations among data bus signals, alternating signals FR and the segment output voltage are given below. www.DataSheet4U.com Data bus DSPOFF O Output Voltage signals HIGH HIGH HIGH HIGH — — EPSON 2–6...

  • Page 31: Absolute Maximum Rating

    = –2.6 or beyond while the LCD driver power source is being applied, the LSI may be permanently damaged and avoid such circumstances. Pay extra attention to the power sequence at times of turning on and turning off the power supply. EPSON 2–7...

  • Page 32: Electrical Characteristics

    =–9.3V, V =–18.6V, consumption (2) =–28.0V Other conditions are the same as with the item I Input terminal Freq.=1MHz D0 ~ D3, LP, FR, capacity Ta=25°C XSCL, SHL, DSPOFF Chips proper Input and output EIO1, EIO2 terminal capacity EPSON 2–8...
  • Page 33 * In case of high speed data transfer, it is necessary to secure a longer XSCL cycle in the timing of the LP pulse insertion in order to maintain the specified value of LP → XSCL ( www.DataSheet4U.com LATCH DATA DSPOFF EPSON 2–9...
  • Page 34 LP HIGH level pulse duration =–3.0V FR delay permissible time –900 +900 =–2.7V EIO setup time =–3.0V *1 6.5MHz equivalence *2 7.5MHz equivalence specifies the time when LP is HIGH and, at the same time, XSCL is LOW. EPSON 2–10...
  • Page 35 =–4.5V ~ 2.7V, V5=–12.0 ~ –28.0V Items Symbols Conditions Min. Max. Unit EIO reset time CL=15pF =–2.7V EIO output delay time (EIO) =–3.0V www.DataSheet4U.com LP → SEG output delay time CL=100pF (0n) FR → SEG output delay time FRSD EPSON 2–11...

  • Page 36: Regarding The Lcd Driving Power

    Insert quick melting fuse in series to the LCD power source for prevention of an excess current flow. It is necessary to choose the optimum value for the protective resistance matching the capacity of the liquid crystal cells. EPSON 2–12...

  • Page 37: An Example Of Connection

    S1D16400 Series 11. AN EXAMPLE OF CONNECTION Block diagram of a large sized LCD www.DataSheet4U.com S1D16700 S1D16700 EPSON 2–13...
  • Page 38 S1D16501 www.DataSheet4U.com Rev.1.0...
  • Page 39 CONTENTS DESCRIPTION ...............................3-1 FEATURES ..............................3-1 BLOCK DIAGRAM ............................3-2 PIN DESCRIPTION ............................3-3 PAD ................................3-4 FUNCTIONAL DESCRIPTION ........................3-6 TIMING CHART .............................3-7 ABSOLUTE MAXIMUM RATINGS ......................... 3-8 ELECTRICAL CHARACTERISTICS ......................3-9 LCD DRIVE POWER ............................ 3-12 TYPICAL CIRCUIT DIAGRAM ........................3-13 www.DataSheet4U.com –...

  • Page 40: Description

    • Wide range of LCD drive voltages: –8 V to –28 V (Absolute maximum rated voltage: –30 V) • Logic system power supply: –2.7 V to –5.5 V • Chip packaging S1D16501D00A (AL-pad die form) • No radial rays countermeasure taken in designing www.DataSheet4U.com EPSON Rev.1.0 3–1...

  • Page 41: Block Diagram

    S1D16501 Series 3. BLOCK DIAGRAM ······································ LCD driver 100 bit Level shifter 100 bit DIO1 Bidirectional shift register 50 × 2 bit YSCL DSPOFF DI3 DIO2 www.DataSheet4U.com EPSON 3–2 Rev.1.0...

  • Page 42: Pin Description

    : 0 V (GND) V : –2.7 V to –5.5 V Power supply LCD drive power supply V : –8 V to –28 V V0, V1, Power supply ≥ V ≥ V ≥ V ≥ V V4, V5 Respectively Total: 119 EPSON Rev.1.0 3–3...

  • Page 43: Pad

    110 × 110µm a Opening (X, Y) PAD No 30 to 109 110 × 110µm b Opening (X, Y) PAD No 20 to 29, 110 to 119 110 × 110µm c Opening (X, Y) PAD No 1 to 19 EPSON 3–4 Rev.1.0...
  • Page 44 6079 –385 –6430 5925 –539 –6560 –32 5771 –693 –6430 –177 5617 –846 –6560 –321 5463 –1000 –6430 –466 5310 –1154 –6560 –610 5156 –1308 5002 –1462 4848 –1616 4694 –1770 4540 –1924 4386 –2078 4232 –2232 EPSON Rev.1.0 3–5...

  • Page 45: Functional Description

    The relationship among the display blanking signal DSPOFF, contents of shift register, AC converted signal FR and On output voltage is as shown in the table below: Content of DSPOFF O output voltage shift register HIGH HIGH (Select level) HIGH HIGH (Non-select level) – – – www.DataSheet4U.com EPSON 3–6 Rev.1.0...

  • Page 46: Timing Chart

    S1D16501 Series 7. TIMING CHART SHL=LOW 1/200 Duty 1 frame (200 lines) DIO1 (DI3) YSCL DSPOFF Shift register ∗ 100 lines DIO2 www.DataSheet4U.com (∗ 50 lines when D13 is input where SEL = HIGH) EPSON Rev.1.0 3–7...

  • Page 47: Absolute Maximum Ratings

    = –2.6 V or less can cause permanent damage to the LSI. Functional operation under these conditions is not implied. Care should be taken to the power supply sequence especially in the system power ON or OFF. EPSON 3–8 Rev.1.0...

  • Page 48: Electrical Characteristics

    µA =V5=–20.0V – current Other conditions are the consumption (2) same as in the item of ISS 1. YSCL, SHL, Input pin – – DSPOFF, FR, capacitance Ta=25°C DI3, SEL Input/output pin – – DIO1, DIO2 capacitance EPSON Rev.1.0 3–9...
  • Page 49 Input signal fall time – – YSCL period – 1000 – YSCL HIGH pulsewidth – – WCLH YSCL LOW pulsewidth – – WCLL Data setup time – – Data hold time – – Allowable FR delay time – –500 EPSON 3–10 Rev.1.0...
  • Page 50 (YSCL - fall to DIO) delay time CL=15pF – DOCL (YSCL - fall to On output) delay time =–12.0 to µs – (DSPOFF to On output) delay time –28.0V CDOFF µs (FR to On Output) delay time CL=100pF – EPSON Rev.1.0 3–11...

  • Page 51: Lcd Drive Power

    LCD power unit. It is then required to select the optimum value in the protection resistance according to the capacitance of LC cell. www.DataSheet4U.com > = t t t Powern ON Power OFF DSPOFF EPSON 3–12 Rev.1.0...

  • Page 52: Typical Circuit Diagram

    S1D16501 Series 11. TYPICAL CIRCUIT DIAGRAM Configuration Drawing of Large Screen LCD – – – – www.DataSheet4U.com EPSON Rev.1.0 3–13...
  • Page 53 S1D16700 www.DataSheet4U.com Rev.1.1...
  • Page 54 CONTENTS DESCRIPTION ...............................4-1 FEATURES ..............................4-1 BLOCK DIAGRAM ............................4-2 PIN DESCRIPTION ............................4-3 PAD ................................4-4 FUNCTIONAL DESCRIPTION ........................4-6 TIMING CHART (S1D16700D01B ) ......................4-7 ABSOLUTE MAXIMUM RATINGS ......................... 4-8 ELECTRICAL CHARACTERISTICS ......................4-9 LCD DRIVE POWER ............................ 4-12 CONNECT EXAMPLE ..........................

  • Page 55: Description

    • Logic system power supply: –2.7 V to –5.5 V • Shipping pattern S1D16700D00A (Al pad chip) S1D16700D01A (Al pad chip) www.DataSheet4U.com S1D16700D00B (Au bump chip) S1D16700D01B (Au bump chip) S1D16700T00A (TCP) S1D16700T01A (TCP) • No radial rays countermeasure taken in designing EPSON Rev.1.1 4–1...

  • Page 56: Block Diagram

    S1D16700 Series 3. BLOCK DIAGRAM COM0 COM99 COM1 COM2 ············ ············ LCD driver 100 bit Voltage control circuit shift register 100 bit DIO1 DIO2 shift register 100 bit YSCL DOFF INH in S1D16700 DOFF in S1D16700 www.DataSheet4U.com EPSON 4–2 Rev. 1.1...

  • Page 57: Pin Description

    : –5.0 V LCD drive power supply V : –7 V to –28 V V0, V1, www.DataSheet4U.com Power supply ≥ V ≥ V ≥ V > V V4, V5 INH for S1D16700 Total: 112 DOFF for S1D16700 EPSON Rev.1.1 4–3...

  • Page 58: Pad

    1) Au bump specification reference values Bump specific : High Quarity Au bump 90µm × 90µm Bump size : 17µm ∼ 28µm Bump height : 2) AL Pad specification reference values 100µm × 100µm Pad Opening : EPSON 4–4 Rev. 1.1...
  • Page 59 1560 -941 1689 -1071 1818 -1201 1948 -2473 -1334 2077 2206 2335 -1357 -157 2584 -1231 -286 2584 -1094 -416 2584 -969 -545 2584 -840 -674 1357 PAD No. 97: INH for S1D16700 DOFF for S1D16700 EPSON Rev.1.1 4–5...

  • Page 60: Functional Description

    The relationship among the display blanking signal INH, contents of the shift register, AC converted signal FR and COM output voltage is as shown in the table below: www.DataSheet4U.com (S1D16700 Contents of COM output voltage shift register HIGH HIGH (Select level) HIGH HIGH (Non-select level) HIGH (Non-select Fixed to LOW level) EPSON 4–6 Rev. 1.1...

  • Page 61: Timing Chart (S1D16700D01B * )

    7. TIMING CHART (S1D16700D01B SHL=LOW 1/200 Duty 1 frame (200 lines) DIO1 YSCL DSPOFF Shift register 100 lines DIO2 www.DataSheet4U.com The V or V non-select level is output corresponding to the FR in S1D16700D00B or INH=LOW, respectively. EPSON Rev.1.1 4–7...

  • Page 62: Absolute Maximum Ratings

    = –2.6 V or more can cause permanent damage to the LSI. Functional operation under these conditions is not implied. Care should be taken to the power supply sequence especially in the system power ON or OFF. www.DataSheet4U.com EPSON 4–8 Rev. 1.1...

  • Page 63: Electrical Characteristics

    =–18.0V, V =–20.0V µA current – Other conditions are the consumption (2) same as in the item of I Input pin YSCL, SHL, – – capacitance DOFF, INH, FR Ta=25°C Input/output pin DIO1, DIO2 – – capacitance EPSON Rev.1.1 4–9...
  • Page 64 – Data hold time – – Allowable FR delay time – –500 The standard applicable to when V = –2.4 V shall be 1.3 times of that WCLH WCLL applies when V = –2.7V to –4.5V. EPSON 4–10 Rev. 1.1...
  • Page 65 –28.0V (INH to COM output) delay time CINH CL=100pF µs (FR to COM output) delay time – The standard applicable at V = –2.4V shall be the same as that employed when V = –2.7V to –4.5V. EPSON Rev.1.1 4–11...

  • Page 66: Lcd Drive Power

    → LCD driving system ON or simultaneous ON of the both At power ON ... Logic system ON At power OFF ... LCD driving system OFF → Logic system OFF or simultaneous OFF of the both www.DataSheet4U.com EPSON 4–12 Rev. 1.1...

  • Page 67: Connect Example

    D0–3 XSCL S1D16006D www.DataSheet4U.com Note *1 It must be provided as the protective resister against overcurrent. Also, the bypass capacitor (0.01 µF) for noise suppression must be provided near to V and V5 terminals on each LSI. EPSON Rev.1.1 4–13...
  • Page 68 S1D16702 www.DataSheet4U.com Rev.1.0...
  • Page 69 CONTENTS DESCRIPTION ...............................5-1 FEATURES ..............................5-1 BLOCK DIAGRAM ............................5-2 PIN DESCRIPTION ............................5-3 PIN LAYOUT ..............................5-4 PAD ................................5-5 FUNCTIONAL DESCRIPTION ........................5-6 TIMING CHART .............................5-7 ABSOLUTE MAXIMUM RATINGS ......................... 5-8 ELECTRICAL CHARACTERISTICS ......................5-9 LCD DRIVE POWER ............................ 5-13 DIFFERENT POINTS FROM REPLACEMENT PRODUCT ................

  • Page 70: Description

    • Logic system power supply: –2.7 V to –5.5 V • Shipping pattern S1D16702D00A (Al pad chip) S1D16702D01A (Al pad chip) S1D16702F00A (80-pin QFP5) www.DataSheet4U.com • No radial rays countermeasure taken in designing • Non-bias display off function EPSON Rev.1.0 5–1...

  • Page 71: Block Diagram

    S1D16702 Series 3. BLOCK DIAGRAM COM0 COM67 COM1 COM2 ············ ············ LCD driver 68 bit shift register 68 bit DIO1 DIO2 shift register 68 bit YSCL * DOFF * INH in S1D16702 DOFF in S1D16702 www.DataSheet4U.com EPSON 5–2 Rev.1.0...

  • Page 72: Pin Description

    Logic power supply : 0 V (GND) V : –5.0 V LCD drive power supply V : –7 V to –28 V Power supply ≥ V ≥ V ≥ V www.DataSheet4U.com >V INH in S1D16702 DOFF in S1D16702 EPSON Rev.1.0 5–3...

  • Page 73: Pin Layout

    COM 18 COM 38 COM 58 COM 19 COM 39 COM 59 DIO1 COM 20 COM 40 COM 60 COM 0 COM 21 COM 41 COM 61 COM 1 COM 22 COM 42 COM 62 COM 2 EPSON 5–4 Rev.1.0...

  • Page 74: Pad

    COM 0 –810 1976 –1098 COM 53 COM 1 –941 COM 27 1976 –969 COM 54 COM 2 –1071 COM 28 1976 –840 COM 55 –66 1357 –1865 –1201 PAD No. 76: INH for S1D16702 DOFF for S1D16702 EPSON Rev.1.0 5–5...

  • Page 75: Functional Description

    The relationship among the display blanking signal INH, contents of shift register, AC converted signal FR and common output voltage is as shown in the table below. www.DataSheet4U.com (S1D16702 Contents of DOFF COM output voltage shift register HIGH HIGH (Select level) HIGH HIGH (Non-select level) (Non-select Fixed to LOW — level) EPSON 5–6 Rev.1.0...

  • Page 76: Timing Chart

    S1D16702 Series 8. TIMING CHART SHL=LOW 1/200 Duty 1 frame (200 lines) DIO1 YSCL Shift register 68 lines DIO2 www.DataSheet4U.com EPSON Rev.1.0 5–7...

  • Page 77: Absolute Maximum Ratings

    = –2.6 V or more can cause permanent damage to the LSI. Functional operation under these conditions is not implied. Care should be taken to the power supply sequence especially in the system power ON or OFF. 3. All the above voltage is based on V = 0 V. www.DataSheet4U.com EPSON 5–8 Rev.1.0...

  • Page 78: Electrical Characteristics

    Average operating =–18.0V, V =–20.0V µA current – Other conditions are the consumption (2) same as in the item of I Input pin YSCL, SHL, – – capacitance INH, FR Ta=25°C Input/output pin – DIO1, DIO2 – capacitance EPSON Rev.1.0 5–9...
  • Page 79 S1D16702 Series Operating Voltage Range VSS – V5 voltage must be set within the following operating voltage range of V – V –30 –28 –20 Operating Voltage Range –10 –7 www.DataSheet4U.com –2.0 –2.4 –3.0 –4.0 –5.0 –5.5 –6. EPSON 5–10 Rev.1.0...
  • Page 80 Data hold time – – Allowable FR delay time – –500 The standard applicable to when V = –2.4 V must be 1.3 times WCLH WCLL of that applies when V = –2.7 V to –4.5 V. EPSON Rev.1.0 5–11...
  • Page 81 (INH to COM output) delay time –28.0V CINH µs (FR to COM output) delay time CL=100pF – The standard applicable when V = –2.4 V must be 1.3 times of that applies when V = –2.7 V to –4.5 V. EPSON 5–12 Rev.1.0...

  • Page 82: Lcd Drive Power

    (2) The inspection process is implemented in the environment that does not allow light to IC. (3) Light shielding measures are established not only for surface of IC but also for rear face and side faces, too. EPSON Rev.1.0 5–13...

  • Page 83: Different Points From Replacement Product

    Bidirectional shift register 68 output segments 68 output segments Output Tr configuration Fig. 1 Fig. 2 PAD layout Identical to the equivalent product – PAD coordinates Different from the equivalent product – Fig. 1 FIg. 2 www.DataSheet4U.com EPSON 5–14 Rev.1.0...
  • Page 84 101 Virginia Street, Suite 290 Telex : 65542 EPSCO HX Crystal Lake, IL 60014, U.S.A. Phone : +1-815-455-7630 Fax : +1-815-455-7633 EPSON TAIWAN TECHNOLOGY & TRADING LTD. 10F, No. 287,Nanking East Road, Sec. 3 Northeast Taipei 301 Edgewater Place, Suite 120...
  • Page 85 In pursuit of “Saving” Technology, Epson electronic devices. Our lineup of semiconductors, liquid crystal displays and quartz devices assists in creating the products of our customers’ dreams. Epson IS energy savings.
  • Page 86 S1D16000 Series Technical Manual ELECTRONIC DEVICES MARKETING DIVISION EPSON Electronic Devices Website http://www.epson.co.jp/device/ First issue November,1990 This manual was made with recycle paper, and printed using soy-based inks. Printed May,2001 in Japan H A...

This manual is also suitable for:

S1d16006d00aS1d16006d00bS1d16006f00aS1d16006d01aS1d16006d01bS1d16400d00b ... Show all

Table of Contents