Table of Contents

Quick Links

BOSCH 844 AND 880
SIMPLE INSTRUCTIONS
ARMING IN AWAY MODE (full arm)
Enter your code + AWAY
or Press button 1 on pendant
STAY Mode allows you to arm the system with predetermined zones disabled. This means
that you can partially arm the system at night while you are still at home, thus giving you
personal protection.
ARMING IN STAY MODE (partial arm)
Enter your code + STAY
or Press button 2 on pendant.
DISARMING
Enter your code + AWAY
or Press button 1 or 2 on pendant.
PANIC ALARM This will create an audible alarm
On code pad press STAY and AWAY simultaneously.
On pendant press both buttons 1 & 2 simultaneously.
TO SILENCE PANIC ALARM
Enter your code + AWAY
or Press either button 1 or 2 on pendant.
Entry time is the time allowed to disarm the system after you have opened the first entry
delay zone. During entry time, the codepad will beep, warning you to disarm your system. If
the system is not disarmed at the expiration of entry time, an alarm will be activated.
Exit time is the amount of time you have to leave your home after you have armed the
system.
or
0 + AWAY
or
0 + STAY
Ph 377 7575
Table of Contents
loading

Summary of Contents for Bosch 844

  • Page 1 BOSCH 844 AND 880 SIMPLE INSTRUCTIONS Ph 377 7575 ARMING IN AWAY MODE (full arm) Enter your code + AWAY 0 + AWAY or Press button 1 on pendant STAY Mode allows you to arm the system with predetermined zones disabled. This means that you can partially arm the system at night while you are still at home, thus giving you personal protection.
  • Page 2 CC404 Operators Guide Solution 844...
  • Page 3 This equipment is set up to carry out test calls at pre- determined times. Such test calls interrupt any other Bosch Security Systems Pty Ltd reserves the right to calls that may be set up on the line at the same time.
  • Page 4: Table Of Contents

    Specifications ..........24 14.0 Reset Latching Outputs ........13 15.0 Codepad ID/Buzzer Tone Change ....13 16.0 Testing ..............13 16.1 Horn Speaker Test..........13 16.2 Bell Test .............13 16.3 Strobe Test............13 16.4 Walk Test Mode ..........13 Bosch Security Systems | 7/05 | F01U009494B...
  • Page 5: Introduction

    1.0 Introduction 2.0 Features Congratulations on selecting the Solution 844 Model The Solution 844 Control Panel uses the latest in CC404 Control Panel to protect you and your microprocessor technology to provide you with more property. To get the most from your unit, read...
  • Page 6: Codepad Indicators

    Zone is unsealed. Zone is sealed. Flashing fast Zone is in alarm. (0.25 sec on/ 0.25 sec off) Flashing slow Zone is manually isolated or (1 sec on/1 sec off) selected to be isolated. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 7: Mains Indicator

    Table 6 defines the audible indicators generated by STAY Mode 2 Arms all zones except those the codepad buzzer. programmed by the Master Code holder to be automatically isolated. Refer to Section 4.3 Arming in STAY Mode 2. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 8: Arming In Away Mode

    [2 5 8 0 #]) before the entry timer expires, the system 24-hour zones when the system is armed in STAY activates the sirens to sound an alarm. Only your Mode 1 or STAY Mode 2. installer can program this option. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 9: Programming Stay Mode 2 Zones

    The Master Code holder can program up to eight Two beeps sound and the STAY and AWAY user codes for the system. indicators turn off. To delete other user codes, repeat this procedure as many times as required. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 10: Radio Transmitter Operations

    The horn speaker emits a distinct fire sound when you press [4] and [6] simultaneously. Contact your installer to disable the ability to activate the codepad fire alarm or to silence the codepad fire alarm. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 11: Medical Alarm

    3. Press [#] after you isolate all selected zones. Two beeps sound and the system returns to the disarmed state. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 12: Fault Analysis Mode

    This type of fault does not cause the FAULT indicator to display on the codepad unless your installer programmed the automatic arming time. Refer to Section 10.0 Setting the Date and Time to program the date and time. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 13: Telco Arm/Disarm Sequence

    Forward - No Answer sequence, or [* 2 1][Phone Number][#] to program the Call Forward Immediate sequence). To program a “*” in the Telco Arm Sequence, enter [* 1]. To program a “#” in the Telco Arm Sequence, enter [* 2]. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 14: Turning Outputs On/Off

    This feature only applies if your system reports by codepad can sound a different tone. telephone. Press and hold [9] until two beeps sound. The system sends a Test Report without sounding the sirens. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 15: Event Memory Recall

    Day alarm turns on. If a zone programmed for day control panel again. alarm operation is activated when the system is disarmed, the codepad beeps. To turn day alarm off Hold down [4] until two beeps sound. Day alarm turns off. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 16: Domestic Dialling

    4-sec pause break 20.2 Programming Domestic Telephone Numbers If your system is configured for domestic dialling, the Master Code holder can program the telephone numbers the control panel calls if an alarm occurs. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 17: Basic Pager Reporting

    Figure 6 shows a transmission from a control panel with an ID number of 678, and Zone 2 in alarm. Figure 6 also shows Zone 3 is manually isolated and the system is armed. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 18: Basic Pager Display

    4 – 0: Zone Normal 7 – 0: AC Normal 1: Alarm 1: AC Failure 2: Zone Bypassed 8 – 0: System Normal 3: Zone Trouble 1: System Fault 5 – 8: Disarmed 9: Armed Bosch Security Systems | 7/05 | F01U009494B...
  • Page 19: Sms Reporting

    Medical Alarm Zone 07 Medical Restore Medical Restore Zone 07 Fuse Fail Fuse Fail Fuse Reset Fuse Fail x = 1 to 16 y = 01 to 16 Bosch Security Systems | 7/05 | F01U009494B...
  • Page 20: Glossary Of Terms

    The ability of the control panel to recognise that detection devices might have stopped working or that the view to a PIR detector is blocked (it is unable to detect any movement during the time programmed by your installer). Bosch Security Systems | 7/05 | F01U009494B...
  • Page 21 User Code The personal identification number an operator uses to arm and disarm the system. Zones A monitored input used to activate an alarm when violated. Bosch Security Systems | 7/05 | F01U009494B...
  • Page 22: Installation Notes

    CC404 | Operators Guide | 24.0 Installation Notes 24.0 Installation Notes Company Name Technician’s Name Technician’s Telephone Number Installation Date Warranty Expires Panel Software Version Service Notes Bosch Security Systems | 7/05 | F01U009494B...
  • Page 23 User Code 11 User Code 4 User Code 12 User Code 5 User Code 13 User Code 6 User Code 14 User Code 7 User Code 15 User Code 8 User Code 16 Bosch Security Systems | 7/05 | F01U009494B...
  • Page 24 Domestic Reporting Domestic Reporting – Number Of Beeps Other System Information Siren Run Time Minutes Sensor Watch Time Increments in Days Can Your System Be Serviced By Another Technician If Yes, Installer’s Code Bosch Security Systems | 7/05 | F01U009494B...
  • Page 25: Specifications

    The Austel permit issued for this product is subject to the following conditions: The Solution 844 Model CC404 Control Panel can only be powered by a Bosch Security Systems TF008 Plug Pack (Approval Number Q92128). Test the sirens, strobe, and zones at weekly intervals.
  • Page 26 Master Code ................18 Medical Alarm ................10 Monitoring Station ..............18 Date and Time ................11 Day Alarm .................14 Deleting Radio User Codes ............8 Off Indicator................6 Deleting User Codes..............8 On Indicator ................6 Detectors ..................18 Disarmed..................18 Disarming ..................8 Bosch Security Systems | 7/05 | F01U009494B...
  • Page 27 STAY Mode 1 ...............7, 19 Deleting ...................8 Entry Guard Timer..............7 STAY Mode 2 ...............7, 19 Entry Guard Timer..............7 Programming Zones ...............8 Walk Test...................13 Strobe Test.................13 System Disarmed ................5 Zone Indicators ................5 Zones ..................19 Bosch Security Systems | 7/05 | F01U009494B...
  • Page 28 CC404 | Operators Guide | Notes EN | 27 Notes Bosch Security Systems | 7/05 | F01U009494B...
  • Page 29 Bosch Security Systems 25 Huntingwood Drive Huntingwood NSW 2148 Australia Phone: +612 9672 1777 Facsimile: +612 9672 1717 © 2005 Bosch Security Systems F01U009494B SKU:920054...

This manual is also suitable for:

880

Table of Contents