Page 1
Gas hob PGB3B5B80A This cooktop is approved for use with Natural Gas and Universal LPG. Leave these instructions with the owner. USER INSTRUCTIONS INSTALLATION INSTRUCTIONS MAINTENANCE INSTRUCTIONS...
Warranty conditions ......15 Produktinfo Additional information on products, accessories, replacement parts and services can be found at www.bosch-home.com and in the online shop www.bosch-eshop.com...
Intended use should be supervised to ensure that they do 8Intended use not play with the appliance. All operations relating to installation, R ead these instructions carefully. You will only connection, regulation and conversion to I n t e n d e d u s e be able to use your appliance safely and other gas types must be performed by an effectively when you have read them.
Important safety information Warning – Risk of fire! (Important safety The cooking process must be supervised. A ■ information short cooking process must be supervised without interruption. D O NOT MODIFY THIS APPLIANCE. The hotplates get very hot. Do not rest Risk of fire! ■...
Installation and connection Preparing to install 5Installation and connection Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to be inserted in a S tatutory requirements benchtop cutout. I n s t a l l a t i o n a n d c o n n e c t i o n This installation must conform with the following: Do not stick the cooktop onto the worktop with silicone.
Installation and connection Clearances If the base of the hotplate can be touched, a protecting shield must be fitted. A range hood fitted above the top must be installed according to the installation instructions for the range The shield must be at least 10 mm from the lowest ■...
Installation and connection Depending on the model, the adhesive seal may be factory-fitted. If this is the case, it should not be removed under any circumstances: the adhesive seal prevents leaks. If the seal has not been factory-fitted, apply it to the underside of the hob, protruding around 3 mm.
Installation and connection Position of the inlet connection: Wiring diagram Use pipe compound or thread sealant, properly threaded pipes and careful assembly procedure so that there is no cross threading, etc., which might cause damage or leakage. Make sure that all connections performed are free of leakage.
Installation and connection Converting the cooktop from Nat. Gas to Adjusting the gas valves Universal LPG Turn the control knobs to the lowest setting. Remove the control knobs from the gas valves. A All work involved in installation, setting and adaptation flexible rubber sealing ring will be visible.
Getting to know your appliance It is essential to ensure that all the burner parts and pan *Getting to know your supports are correctly installed for the appliance to appliance work correctly. Do not swap the burner caps around. B urner locations G e t t i n g t o k n o w y o u r a p p l i a n c e Elements Ignition plug...
Gas burners An orange-coloured flame is normal. This is caused by ÄGas burners the presence of dust in the atmosphere, spilt liquids, etc. If the burner flames are accidentally blown out, switch S witching on manually off the burner operating control knob and do not try to G a s b u r n e r s relight it for at least 1 minute.
Cleaning and maintenance Always centre the pan over 2Cleaning and maintenance the burner, not to one side. Otherwise it could tip over. Do not place large pans on C leaning the burners near the control C l e a n i n g a n d m a i n t e n a n c e Once the appliance is cool, use a sponge to clean it knobs.
Trouble shooting Only authorized personnel from the Service Centre are 3Trouble shooting qualified to work on the appliance. Sometimes certain faults detected can be easily D O NOT MODIFY THIS APPLIANCE. resolved. Before calling the Technical Assistance T r o u b l e s h o o t i n g Service, bear in mind the following advice: Fault Possible cause...
Customer service 4Customer service W hen contacting our Technical Assistance Service, C u s t o m e r s e r v i c e please provide the product number (E-Nr.) and production number (FD) of the appliance. This information is given on the specifications plate located on the lower section of the hob and on the label in the user manual.