Quick Links
KD-DV7206/KD-DV7205
Installation/Connection Manual
GET0375-006A
[U/UT]
ENGLISH
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and gearshift lever operations.
– it may obstruct the operation of safety devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while driving, be sure to look ahead carefully.
• The driver must not watch the monitor while driving.
If the parking brake is not engaged, "DRIVER MUST NOT WATCH THE MONITOR WHILE
DRIVING." appears on the monitor, and no playback picture will be shown.
– This warning appears only when the parking brake wire is connected to the parking brake
system built in the car.
To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car's chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both at
the rear and at the front, with an impedance of 4
50 W, change "AMP GAIN" setting to prevent the speakers from being damaged (see page 27 of the
INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
to 8 ). If the maximum power is less than
Heat sink
12 V
JVC
•
•
•
•
50 W
AMP GAIN
•
1
0106DTSMDTJEIN
EN, CT
© 2006 Victor Company of Japan, Limited
JVC
50 W
4
8
27
Related Manuals for JVC KD-DV7206
Summary of Contents for JVC KD-DV7206
- Page 1 • Be sure to ground this unit to the car’s chassis again after installation. Notes: • Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio 50 W dealer.
-
Page 2: Troubleshooting
Parts list for installation and connection If any item is missing, consult your JVC car audio dealer immediately. A / B Hard case/Control panel Sleeve Trim plate Power cord Crimp connector Washer (ø5) Lock nut (M5) Mounting bolt (M5 × 20 mm) (ø5) -
Page 3: Removing The Unit
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits. • If you are not sure how to install this unit correctly, have it installed by a qualified technician. -
Page 4: Electrical Connections
ENGLISH ELECTRICAL CONNECTIONS Typical connections / Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color. Connect the colored leads of the power cord in the order specified in the illustration below. - Page 5 Connecting the parking brake wire / When installing the monitor in a location where it can be seen by the driver Connect the parking brake wire to the parking brake system built in the car. Parking brake wire (light green) Parking brake To metallic body or chassis of the car Parking brake switch (inside the car)
- Page 6 Failure to do so may cause damage to the unit. Connecting the external components / CD changer, Apple iPod®, or JVC D. player / CD Apple iPod® JVC D. player • Set “CHANGER” for the external input setting (See page 26 of the INSTRUCTIONS.) / “CHANGER”...