Table of Contents
Quick Links
Table of Contents
Related Manuals for Epson ELPMB64
Summary of Contents for Epson ELPMB64
- Page 1 Short Throw Projector Wall Mount Installation Guide...
-
Page 2: Table Of Contents
Contents Introduction Using the Product Safely ....1 Safety Indications ..... . . 1 Explanation of Symbols . -
Page 3: Using The Product Safely
Introduction Using the Product Safely For your safety, read all the instructions in this guide before using this product. Incomplete or incorrect installation could cause damage to the product or result in personal injury or property damage. Keep this installation manual at hand for later reference. Read the User's Guide and Safety Instructions for your projector and follow the instructions in these documents. - Page 4 Wall mount and resist any horizontal vibration. Use M8 nuts, bolts and so on. Nuts and bolts smaller than M8 could cause the mount to fall. Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation.
-
Page 5: Notes On The Installation Location
If any abnormalities occur with this product, immediately disconnect the cables from the product, and then contact your local dealer or the nearest Epson service call center. Continuing to use the product in an abnormal condition could cause a fire, electric shock, or visual impairment. -
Page 6: Accessories
Introduction Caution Carry out power supply wiring work at the installation location of the projector in advance. Install the projector at a place away from other electric devices such as fluorescent lights or air conditioning. Some types of fluorescent lights could interfere with the remote control. Accessories Part Name... - Page 7 Introduction Part Name Cable cover Arm cover M4 x 12 mm hexagon socket head cap bolts with washer (x1) M4 x 12 mm hexagon socket head cap bolts without washers (x6) M4 x 12 mm hexagon socket head cap bolts with washers/spring washers (x5) M8 x 16 mm hexagon socket head cap bolts without washers (x7)
-
Page 8: Specifications
Introduction Specifications Weight Approx. 9.7kg Maximum load capacity 6.5 kg Arm length 1,000 to 1,510 mm (from wall plate attachment point to arm cover point) Vertical slide adjustment 0 to 134 mm (arm length minimum) range 0 to 230 mm (arm length maximum) Vertical tilt adjustment range -7 to 17°... - Page 9 Introduction Units: mm *Offset value for the center of the projection screen and the center of the wall plate...
-
Page 10: Installing The Wall Mount
Installing the Wall mount Determining the installation position (projection distance tables) See the table on the next page and install so that the image is projected at the optimum size for the screen. The values are a guide. The recommended range for the projection distance (A) is 70 to 119 cm. A: Shortest projection distance (wide) B: Vertical slide adjustment C: Distance from the top of the projection surface to the ceiling... -
Page 11: Wxga Projector
Installing the Wall mount WXGA projector 16:10 projection screen [Units: cm] 68 " 146.5 × 91.5 69 " 148.6 × 92.9 70 " 150.8 × 94.2 71 " 152.9 × 95.6 72 " 155.1 × 96.9 73 " 157.2 × 98.3 74 "... - Page 12 Installing the Wall mount 94 " 202.5 × 126.5 95 " 204.6 × 127.9 96 " 206.8 × 129.2 97 " 208.9 × 130.6 98 " 211.1 × 131.9 99 " 213.2 × 133.3 100 " 215.4 × 134.6 101 " 217.5 ×...
-
Page 13: 16:9 Projection Screen
Installing the Wall mount 16:9 projection screen [Units: cm] 66 " 146.1 × 82.2 67 " 148.3 × 83.4 68 " 150.5 × 84.7 69 " 152.8 × 85.9 70 " 155.0 × 87.2 71 " 157.2 × 88.4 72 " 159.4 ×... - Page 14 Installing the Wall mount 92 " 203.7 × 114.6 93 " 205.9 × 115.8 94 " 208.1 × 117.1 95 " 210.3 × 118.3 96 " 212.5 × 119.5 97 " 214.7 × 120.8 98 " 217.0 × 122.0 99 " 219.2 ×...
-
Page 15: 4:3 Projection Screen
Installing the Wall mount 4:3 projection screen [Units: cm] 60 " 121.9 × 91.4 61 " 124.0 × 93.0 62 " 126.0 × 94.5 63 " 128.0 × 96.0 64 " 130.0 × 97.5 65 " 132.1 × 99.1 66 " 134.1 ×... - Page 16 Installing the Wall mount 86 " 174.8 × 131.1 87 " 176.8 × 132.6 88 " 178.8 × 134.1 89 " 180.8 × 135.6 90 " 182.9 × 137.2 91 " 184.9 × 138.7 92 " 186.9 × 140.2 93 " 189.0 ×...
-
Page 17: Xga Projector
Installing the Wall mount XGA projector 4:3 projection screen [Units: cm] 63 " 128.0 × 96.0 64 " 130.0 × 97.5 65 " 132.1 × 99.1 66 " 134.1 × 100.6 67 " 136.1 × 102.1 68 " 138.2 × 103.6 69 "... - Page 18 Installing the Wall mount 87 " 176.8 × 132.6 88 " 178.8 × 134.1 89 " 180.8 × 135.6 90 " 182.9 × 137.2 91 " 184.9 × 138.7 92 " 186.9 × 140.2 93 " 189.0 × 141.7 94 " 191.0 ×...
-
Page 19: 16:9 Projection Screen
Installing the Wall mount 16:9 projection screen [Units: cm] 58 " 128.4 × 72.2 59 " 130.6 × 73.5 60 " 132.8 × 74.7 61 " 135.0 × 76.0 62 " 137.3 × 77.2 63 " 139.5 × 78.5 64 " 141.7 ×... - Page 20 Installing the Wall mount 84 " 186.0 × 104.6 85 " 188.2 × 105.8 86 " 190.4 × 107.1 87 " 192.6 × 108.3 88 " 194.8 × 109.6 89 " 197.0 × 110.8 90 " 199.2 × 112.1 91 " 201.5 ×...
-
Page 21: 16:10 Projection Screen
Installing the Wall mount 16:10 projection screen [Units: cm] 60 " 129.2 × 80.8 61 " 131.4 × 82.1 62 " 133.5 × 83.5 63 " 135.7 × 84.8 64 " 137.9 × 86.2 65 " 140.0 × 87.5 66 " 142.2 ×... - Page 22 Installing the Wall mount 86 " 185.2 × 115.8 87 " 187.4 × 117.1 88 " 189.5 × 118.5 89 " 191.7 × 119.8 90 " 193.9 × 121.2 91 " 196.0 × 122.5 92 " 198.2 × 123.9 93 " 200.3 ×...
-
Page 23: Assembly And Installation
Installing the Wall mount Assembly and Installation Follow the work flow below to install the wall mount. Installing the wall plate Check the position where you want to install the wall plate, and then mark that position on the wall. Attach the wall plate so that the center of the screen and the marked gauge line of the wall plate are on the same line as shown in the following illustration. - Page 24 Installing the Wall mount Drill holes of the following diameters and depths at the points you marked. Drill diameter 8.5 mm Pilot hole depth 40 mm Anchor hole depth 35 mm Use a device such as a dust pump to clean out concrete dust from the hole. Position the wall plate on the wall and insert M8 x 60 mm expansion anchors into the holes.
-
Page 25: Assembling The Wall Mount
Installing the Wall mount Assembling the wall mount Attach the adjustment unit to the arm unit. Secure temporarily using the hexagonal wrenches (M4 and M8) and M4 x 12 mm hexagon socket head cap bolt and M8 x 16 mm hexagon socket head cap bolt. -
Page 26: Routing The Cables Through The Arm Unit
Installing the Wall mount Routing the cables through the arm unit Caution Problems may occur if you use this product without routing the cables through the arm unit. Attaching the arm unit to the wall plate Attach the hook on the arm plate to the bar on the wall plate. Be careful not to pinch cables between the arm plate and the wall plate. -
Page 27: Attaching The Projector To The Adjustment Unit
Installing the Wall mount Attach the projector plate to the projector using the hexagonal wrench (M4) and three M4 x 12 mm bolts with washers/spring washers. a: Projector lens side Warning If you apply adhesives to prevent the screws from loosening, or if you use lubricants or oils on the wall mount plate fixing points, the housing may crack and cause the projector to fall, resulting in personal injury or property damage. -
Page 28: Extending The Arm, Adjusting The Length, And Securing Temporarily
Installing the Wall mount Secure the adjustment unit temporarily at the points marked using two M4 x 12 mm hexagon socket head cap bolts as shown below. a: Mark Extending the arm, adjusting the length, and securing temporarily Loosen the screw on the arm. ( Adjust the length of the arm using the measuring scale on the bottom to match the distance recommended in the projection distance table for each model. -
Page 29: Attaching The Cable Cover
Installing the Wall mount Attaching the cable cover Take up the cable slack, and then secure the cable cover with the screws as shown below. Warning Do not place the excess cable on top of the cable cover. Doing so could cause the mount to fall. Turning on the projector and checking the screen Plug in the projector. - Page 30 Installing the Wall mount Loosen the screws (A, B, C, D) on the adjustment unit, and adjust the position of the projection screen while changing the direction and position of the projector. A : Vertical tilt adjustment : -7 to 17° (arm length minimum) : -17 to 7°...
-
Page 31: Installing The Safety Wire
Installing the Wall mount Installing the safety wire Connect the projector to the wall mount to prevent the projector from falling. Attaching the arm cover Secure the arm cover with a hexagonal wrench (M4) and an M4 x 12 mm hexagon socket head cap bolt. Attaching the wall plate cover Secure the wall plate cover with a hexagonal wrench (M4) and three M4 x 12 mm hexagon socket head cap bolts. - Page 32 Do not hang on the mount or hang a heavy object on it. Or do not hang a heavy object on the mount. If the mount or the projector falls, it could cause personal injury or property damage. If the projector or the arm unit falls down, it could cause personal injury or property damage. © 2020 Seiko Epson Corporation 414023800 EN...