Bosch AUTODOME IP starlight 5100i IR Installation Manual

Bosch AUTODOME IP starlight 5100i IR Installation Manual

Hide thumbs Also See for AUTODOME IP starlight 5100i IR:

Quick Links

AUTODOME IP starlight 5100i IR
en
Installation Manual
Table of Contents
loading

Summary of Contents for Bosch AUTODOME IP starlight 5100i IR

  • Page 1 AUTODOME IP starlight 5100i IR Installation Manual...
  • Page 3: Table Of Contents

    AUTODOME IP starlight 5100i IR Table of contents | en Table of contents Safety About this manual Legal information Safety precautions Important safety instructions Connection in applications Important notices Important notices - illumination safety Customer support and service Introduction Parts List...
  • Page 4: Safety

    Legal information Copyright This manual is the intellectual property of Bosch Security Systems, and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.
  • Page 5: Important Safety Instructions

    ® Electrical Code (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1), and all applicable local codes. Bosch Security Systems accepts no liability for any damages or losses caused by incorrect or improper installation. Warning! Risk of bodily injury, property damage, or damage to the unit Because of the weight of the camera, do not use the optional extension pipe (NDA-U-PMTE) to extend the pipe while using the pipe mount (NDA-U-PMT or NDA-U-PMTS).
  • Page 6 Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information.
  • Page 7: Connection In Applications

    AUTODOME IP starlight 5100i IR Safety | en Connection in applications 24 VAC power source: This unit is intended to operate at 24 VAC (if PoE is not available). User-supplied wiring must be in compliance with electrical codes (Class 2 power levels).
  • Page 8: Important Notices

    | Safety AUTODOME IP starlight 5100i IR Important notices Notice! This device is intended for use in public areas only. U.S. federal law strictly prohibits surreptitious recording of oral communications. Notice! This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
  • Page 9: Customer Support And Service

    2.19 Infrared Hazard Hazard Distance 279 mm Customer support and service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. USA and Canada Telephone: 800-289-0096, option 5 Fax: 800-366-1329 Email: [email protected]...
  • Page 10 | Safety AUTODOME IP starlight 5100i IR More Information For more information, please contact the nearest Bosch Security Systems location or visit www.boschsecurity.com. 2021-02-19 | 0.7 | Bosch Security Systems Installation Manual...
  • Page 11: Introduction

    * Refer to the chapter Preparing Wiring. Additional tools required The table that follows is a list of additional tools (not supplied by Bosch) required to install an AUTODOME camera or its accessories: Bosch Security Systems 2021-02-19 | 0.7 |...
  • Page 12: Establishing The Connection

    You can also use the Project Assistant app to complete the initial configuration of the camera. In order to use this device with the Project Assistant app by Bosch, you must download the app from the Bosch Download Store, from Google Play, or from the Apple Store.
  • Page 13: Product Description

    Product Description | en Product Description Keep your security in focus with the many features of the AUTODOME IP starlight 5100i IR camera. The camera is carefully tuned to deliver detailed, 4MP ultra HD images during the day as well as full details in low-light or no-light conditions. The integrated, intelligent IR illuminator automatically adjusts the IR intensity according to zoom factor and field of view to ensure that the scene is illuminated uniformly.
  • Page 14: Preparing Wiring

    | Preparing Wiring AUTODOME IP starlight 5100i IR Preparing Wiring Prepare and install all wiring for 24 VAC, PoE (Cat5e or better), alarms, and audio as necessary. For 24 VAC, follow the recommendations for maximum cable distance and wire gage.
  • Page 15: (Optional) Configuration Programming On A Temporary Table-Top Stand

    AUTODOME IP starlight 5100i IR (Optional) Configuration Programming on a Temporary Table-top Stand | en (Optional) Configuration Programming on a Temporary Table-top Stand Installation Overview Caution! Risk of damage to camera Please remove the tape from the top of the camera. The camera head must be free to rotate.
  • Page 16 | (Optional) Configuration Programming on a Temporary Table-top Stand AUTODOME IP starlight 5100i IR 24VAC 50/60Hz 802.3bt PoE Configure the camera. Refer to the separate User Manual for details. Disconnect the wires/cables from the connectors in the base of the camera.
  • Page 17: Optional) Installing A Microsd Card

    AUTODOME IP starlight 5100i IR (Optional) Installing a microSD card | en (Optional) Installing a microSD card Loosen the 2 Hex screws in the back of the camera housing. Pull up the cover of the SD card slot as illustrated in the graphic that follows.
  • Page 18 | (Optional) Installing a microSD card AUTODOME IP starlight 5100i IR 2021-02-19 | 0.7 | Bosch Security Systems Installation Manual...
  • Page 19: Installing The Ip66 Kit

    AUTODOME IP starlight 5100i IR Installing the IP66 kit | en Installing the IP66 kit The camera box includes the IP66 accessory kit. To ensure a waterproof seal on the camera connectors, assemble the IP66 kit on the Ethernet cable (Cat5e or better) before you finish camera installation.
  • Page 20 | Installing the IP66 kit AUTODOME IP starlight 5100i IR Put the grommet on the RJ45 socket on the camera cable on the camera. Note: Do not complete the steps that follow until you are ready to complete step 7 of the subchapter Attaching the Mounting Cap and the Camera.
  • Page 21 AUTODOME IP starlight 5100i IR Installing the IP66 kit | en Bosch Security Systems 2021-02-19 | 0.7 | Installation Manual...
  • Page 22: Optional) Installing The Surveillance Cabinet

    | (Optional) Installing the Surveillance Cabinet AUTODOME IP starlight 5100i IR (Optional) Installing the Surveillance Cabinet The surveillance cabinet can attach directly to a wall mount, to a corner mount, to a pipe mount, or to a pole mount.
  • Page 23: Installing A Pendant Wall Mount And Camera

    AUTODOME IP starlight 5100i IR Installing a Pendant Wall Mount and Camera | en Installing a Pendant Wall Mount and Camera Installing a Pendant Wall Mount (with the Surveillance Cabinet) Slide the mounting flange over the wall mount. Attach the wall mount to the mounting flange and fix them on the front door of the Wall- mount Surveillance Cabinet by using four M5 screws.
  • Page 24: Attaching The Mounting Cap And The Camera

    | Installing a Pendant Wall Mount and Camera AUTODOME IP starlight 5100i IR Attaching the Mounting Cap and the Camera To ensure a watertight seal, wrap Teflon tape (user-supplied) four times around the threads at the end of the mount.
  • Page 25 AUTODOME IP starlight 5100i IR Installing a Pendant Wall Mount and Camera | en Put the camera at approximately 45 degrees. Install the camera in the mounting cap with the hook. Bosch Security Systems 2021-02-19 | 0.7 | Installation Manual...
  • Page 26 | Installing a Pendant Wall Mount and Camera AUTODOME IP starlight 5100i IR Connect the RJ45 plug and the RJ45 socket on the camera cable and assemble the IP66 accessory kit to ensure a waterproof seal. Connect the mating connectors on the user-supplied cables to the matching connectors on the camera.
  • Page 27 AUTODOME IP starlight 5100i IR Installing a Pendant Wall Mount and Camera | en Place the line through the base on the camera. Bosch Security Systems 2021-02-19 | 0.7 | Installation Manual...
  • Page 28 | Installing a Pendant Wall Mount and Camera AUTODOME IP starlight 5100i IR 10. Match the miter lock of the cap and the camera. 2021-02-19 | 0.7 | Bosch Security Systems Installation Manual...
  • Page 29 AUTODOME IP starlight 5100i IR Installing a Pendant Wall Mount and Camera | en 11. Secure the 4 safety locking screws with the T15 Torx screwdriver. Bosch Security Systems 2021-02-19 | 0.7 | Installation Manual...
  • Page 30 | Installing a Pendant Wall Mount and Camera AUTODOME IP starlight 5100i IR 2021-02-19 | 0.7 | Bosch Security Systems Installation Manual...
  • Page 31: Installing A Parapet Roof Mount And Camera

    AUTODOME IP starlight 5100i IR Installing a Parapet Roof Mount and Camera | en Installing a Parapet Roof Mount and Camera 10.1 Installing the Roof Mount Determine the wall location on the roof for the camera and use the pendant parapet mount bracket as a template to mark the hole locations.
  • Page 32 | Installing a Parapet Roof Mount and Camera AUTODOME IP starlight 5100i IR Remove the End Cap from the front of the arm. Feed the video, control, and power wires up through the bottom of the pipe arm and out the front end.
  • Page 33: Attaching The Mounting Cap And The Camera

    AUTODOME IP starlight 5100i IR Installing a Parapet Roof Mount and Camera | en 10.2 Attaching the Mounting Cap and the Camera To ensure a watertight seal, wrap Teflon tape (user-supplied) four times around the threads at the end of the mount.
  • Page 34 | Installing a Parapet Roof Mount and Camera AUTODOME IP starlight 5100i IR Put the camera at approximately 45 degrees. Install the camera in the mounting cap with the hook. Connect the RJ45 plug and the RJ45 socket on the camera cable and assemble the IP66 accessory kit to ensure a waterproof seal.
  • Page 35 AUTODOME IP starlight 5100i IR Installing a Parapet Roof Mount and Camera | en Place the line through the base on the camera. Bosch Security Systems 2021-02-19 | 0.7 | Installation Manual...
  • Page 36 | Installing a Parapet Roof Mount and Camera AUTODOME IP starlight 5100i IR 10. Match the miter lock of the cap and the camera. 2021-02-19 | 0.7 | Bosch Security Systems Installation Manual...
  • Page 37 AUTODOME IP starlight 5100i IR Installing a Parapet Roof Mount and Camera | en 11. Secure the 4 safety locking screws with the T15 Torx screwdriver. Bosch Security Systems 2021-02-19 | 0.7 | Installation Manual...
  • Page 38 | Installing a Parapet Roof Mount and Camera AUTODOME IP starlight 5100i IR 2021-02-19 | 0.7 | Bosch Security Systems Installation Manual...
  • Page 39: Installing A Pipe Mount And Camera

    AUTODOME IP starlight 5100i IR Installing a Pipe Mount and Camera | en Installing a Pipe Mount and Camera 11.1 Preparing the Ceiling for Installation Determine a secure location for the pipe mount. Ensure there is an adequate opening in the ceiling or mounting structure for the cables to pass through.
  • Page 40: Attaching The Mounting Cap And The Camera

    | Installing a Pipe Mount and Camera AUTODOME IP starlight 5100i IR 11.3 Attaching the Mounting Cap and the Camera To ensure a watertight seal, wrap Teflon tape (user-supplied) four times around the threads at the end of the mount.
  • Page 41 AUTODOME IP starlight 5100i IR Installing a Pipe Mount and Camera | en Put the camera at approximately 45 degrees. Install the camera in the mounting cap with the hook. Connect the RJ45 plug and the RJ45 socket on the camera cable and assemble the IP66 accessory kit to ensure a waterproof seal.
  • Page 42 | Installing a Pipe Mount and Camera AUTODOME IP starlight 5100i IR Place the line through the base on the camera. 2021-02-19 | 0.7 | Bosch Security Systems Installation Manual...
  • Page 43 AUTODOME IP starlight 5100i IR Installing a Pipe Mount and Camera | en 10. Match the miter lock of the cap and the camera. Bosch Security Systems 2021-02-19 | 0.7 | Installation Manual...
  • Page 44 | Installing a Pipe Mount and Camera AUTODOME IP starlight 5100i IR 11. Secure the 4 safety locking screws with the T15 Torx screwdriver. 2021-02-19 | 0.7 | Bosch Security Systems Installation Manual...
  • Page 45 AUTODOME IP starlight 5100i IR Installing a Pipe Mount and Camera | en Bosch Security Systems 2021-02-19 | 0.7 | Installation Manual...
  • Page 46: Connection

    | Connection AUTODOME IP starlight 5100i IR Connection Caution! Compliance with EN50130-4 Alarm Standard – CCTV for Security Applications To meet the requirements of the EN50130-4 Alarm Standard, an ancillary uninterruptable power (UPS) supply is necessary. The UPS must have a Transfer Time between 2–6 ms and a Backup Runtime of greater than 5 seconds for the power level as specified on the product datasheet.
  • Page 47 AUTODOME IP starlight 5100i IR Connection | en Label ID Description Cable Wire Color ALARM_IN1 Alarm In 1 White ALARM_IN2 Alarm In 2 Blue AUDIO OUT Audio Out Grey Ground Black AUDIO GND Audio Ground Green AUDIO IN Audio In...
  • Page 48: Maintenance

    Dry the bubble thoroughly with a dry nonabrasive cloth to prevent water spots. Never scrub the bubble with any abrasive material or cleaners. Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean & Shine (or equivalent), according to manufacturer’s instructions. Refer to www.novuspolish.com...
  • Page 49: Decommissioning

    The unit should only be passed on together with this installation guide. 14.2 Disposal Disposal - Your Bosch product was developed and manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material.
  • Page 50: Technical Data

    | Technical data AUTODOME IP starlight 5100i IR Technical data For product specifications, see the datasheet for your camera, available on the appropriate product pages of the Online Product Catalog at www.boschsecurity.com. 2021-02-19 | 0.7 | Bosch Security Systems...
  • Page 51: Support

    – Troubleshooting – Repair & Exchange – Product Security Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ Bosch Security Systems 2021-02-19 | 0.7 | Installation Manual...
  • Page 52 | Support AUTODOME IP starlight 5100i IR 2021-02-19 | 0.7 | Bosch Security Systems Installation Manual...
  • Page 54 Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2021 202102202058...

Table of Contents