Related Manuals for Forest SHUTTLE S Z-Wave
Summary of Contents for Forest SHUTTLE S Z-Wave
- Page 1 Installing the FOREST SHUTTLE ® S / M / L Z - W a v e...
- Page 2 Connect the 24V plug into the socket of to the power socket of Shuttle L the Shuttle S and connect the AC plug to the wall socket. loop the cord through the strain relief 2 │ Installing the Forest Shuttle® S / M / L Z-Wave...
- Page 3 ⑥ Setting the end limits of the FOREST SHUTTLE® S / M / L Z-Wave Before setting the end limits, the RF remote or IR remote channel can be programmed. The stack back (adjusted open limit) can be set by remote or switch. For programming see page 4.
-
Page 4: Dry Contact Inputs
Default setting is high sensitive. Touch Impulse can be set to less sensitive or off, with 9 or 10 presses respectively. To confirm, press button once more for 4 seconds until the led blinks 3 times and goes OFF. 4 │ Installing the Forest Shuttle® S / M / L Z-Wave... -
Page 5: Factory Default
If necessary, change the IR channel as shown on page 4. Factory default: To reset all settings, press button 16x. To confirm, press button once more for 4 seconds until the led blinks 3 times and goes OFF. 5 │ Installing the Forest Shuttle® S / M / L Z-Wave... - Page 6 Connecting to port 1 or port 2 of the FOREST SHUTTLE® S / M / L Z-Wave do-it-yourself plug pin8 pin1 pin8 pin1 (CLOSE) (OPEN) (CLOSE) (OPEN) MANUAL SWITCH CONNECTED TO DRY CONTACT INPUTS A manual switch or a relay output of a Home Automation System can easily be connected to the Shuttle S or L. Be sure the switch/relay is potential free.
- Page 7 Advanced Z-Wave configuration of the FOREST SHUTTLE® S / M / L Z-Wave Z-Wave Plus: Yes Z+ Plus Role type: ROLE_TYPE_SLAVE_ALWAYS_ON Z+ Device type: WINDOW_COVERING_POSITION_ENDPOINT_AWARE Basic type: BASIC_TYPE_ROUTING_SLAVE Generic type: GENERIC_TYPE_SWITCH_MULTILEVEL Specific type: SPECIFIC_TYPE_CLASS_C_MOTOR_CONTROL Listening: TRUE Z-Wave Lib: 6.51.10 Supporting command classes...
- Page 8 It is most likely that a controller or screen is associated in this group to (unsolicited) report any changes to the curtain rail position. Specific group report Because there is only association group the reported group with this command is always group 1. 8 │ Installing the Forest Shuttle® S / M / L Z-Wave...
- Page 9 The curtain rail is moved to position 20% after 10 seconds. NOTE 2: due to the limitations of this type of multilevel, a curtain rail the Start Level byte of the SWITCH_MULTILEVEL_START_LEVEL_CHANGE command is ignored in all cases. 9 │ Installing the Forest Shuttle® S / M / L Z-Wave...
- Page 10 Because this product supports version 2 it reports the additional information: hardware version and number of firmware targets. COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 This will report information about the manufacturer. This product will contain the manufacturer ID of Forest Group NL. Manufacturer ID of Forest Group NL is 0x0207, the ID of this product is 39.
- Page 11 Technical specification of the FOREST SHUTTLE® S / M / L Z-Wave Shuttle® S Z-wave Shuttle® M Z-wave Shuttle® L Z-wave Part# EU freq. 868.4MHz: n/a 5232000004 5232000002 US freq. 908.4MHz: 5232000005 5232000006 Voltage Shuttle®: 24Vdc 24Vdc 100 - 240V~ 50 - 60Hz 0.8A Max.
- Page 12 It is important for the safety of persons to follow these instructions. Save these instructions. Do not use the product for any other purpose than intended. In order for the Forest Shuttle S / M / L to function correct and safe, the complete curtain system must be assembled with original parts and devices of Forest Group Nederland B.V.