Table of Contents
Table of Contents
Related Manuals for Honeywell Temaline TK-S014
Summary of Contents for Honeywell Temaline TK-S014
- Page 1 Temaline TK_S014 (RTU A08) Installation Manual TK_S014 – Installation Manual...
- Page 2 In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The information and specifications in this document are subject to change without notice.
-
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ............................... 5 TK_S014 (RTU A08) ? ........................5 RTU A08 ..................5 TOGETHER WITH OTHER EMALINE DEVICES Readers ..............................5 Interactive Terminals ..........................5 Compositions with phased out devices ..................... 6 ..........................7 ELATED DOCUMENTATION PREPARING FOR INSTALLATION ......................... 8 ............................. - Page 4 Cables rules ............................19 ACTIVATION ..............................20 RTUA08 ............20 HECKING THE COMMUNICATION BETWEEN ERVER ......................... 21 OLLECTING DEVICE INFORMATION TECHNICAL DATA ............................22 REGULATION COMPLIANCE ........................24 CE C ............................24 OMPLIANCE FCC N ..............................24 OTICE ..................... 24 ANADIAN AND NITED TATES...
-
Page 5: Introduction
INTRODUCTION What TK_S014 (RTU A08) is? TK_S014 is a Temaline device acting as a single door controller. It can manage up two third party Wiegand readers (on the two sides of the doors), the inputs / outputs used for the management of such readers (led and buzzers) and the inputs / outputs needed for the management of the door (door state, REX button, lock commands). -
Page 6: Compositions With Phased Out Devices
Compositions with phased out devices Note: These compositions are done including some phase out devices cannot anymore be purchased. This list is left here just for maintenance reference. Terminals Code Composition Notes TK_D014 RTU-C01 + RTU-A08 + RTU-S01 + third Horizontal mounting. -
Page 7: Related Documentation
Related documentation Document Content EBI Temaline Interface - Temaline Access Further information on the EBI Tema system, Control Configuration Guide complete commissioning steps and system configuration are included in the, which is provided with EBI documentation package. Temaline - installation in Harsh Environment: It is a whitepaper with Temaline system rules on this topic. -
Page 8: Preparing For Installation
PREPARING FOR INSTALLATION Contents of the kit Before you begin, unpack the shipment and check the parts list against the components in the shipment. Your shipment should contain: • RTU A08 device • Support kit with the following: 2 white resistors (392Ω 1% 1/4W) 2 yellow resistors (1210Ω... -
Page 9: Wiring Characteristics
The connections shown are: • The Power supply connection: it connects the Power Supply device whit other Temaline devices • The LonWorks connection: to connect the TemaServer with the RTUs • The Input and Output are used to connect the physical door managed (lock, Door sense, REX and others) •... -
Page 10: Input Wires
Table 2. Length/Capacity of LONWORKS Data Cables (m) The FTT10A Echelon v1.2 User Guide recommends the cables indicated in Table 3. Producer and Model Connection to bus Connection in Connection in free -maximum total free topology – topology – length [m] maximum node- maximum total... - Page 11 The wires used to connect the RTU-A08 to the reader(s) are those specified into the reader technical specification. TK_S014 – Installation Manual...
-
Page 12: Mounting The Device
MOUNTING THE DEVICE Mounting on DIN/omega rail The device is mounted on standard DIN/omega rail; to mount it you should follow these steps: 1. Hook the bottom of the RTU-A08 onto the upper margin of the DIN/omega Rail. 2. Push until it clips onto the rail. (See Figure 2). CLIP Figure 2. -
Page 13: Closing The Rtua08 Module
Closing the RTUA08 Module To close the unit, follow these steps (see Figure 4): • Clip the cover onto the module. • Screw on the module cover with the 4 self-tapping screws (requires a 3mm cross-head screwdriver). RTU-A08 Figure 4. Closing the RTUA08 Module TK_S014 –... -
Page 14: Wiring Operation
WIRING OPERATION Elemental Detail Figure 12 shows a detail of the electronic board, including the positions of the main connectors and service elements. Figure 5. Elemental Detail Connection of power supply cables The RTU A08 device must be powered with a 12V DC power supply. To determine the correct size of the power cable please refer to Table 1. -
Page 15: Daisy Chain Connection (Bus)
It is possible to connect TemaServer and the RTU in two different ways: • Daisy chain (also known as Bus) • Free topology (also known as Star) Based on the type of connection used in your plant some terminator resistors are required; if you don’t install them the RTU A08 device will not work in a proper way. -
Page 16: Lonwork Cables Connection
Figure 8 Free topology connection Lonwork cables connection Screw the twisted pair cable to LON-A and LON-B ® The polarity of the LONWORKS cables is not significant. Figure 9 LON cable connectuion A very common error in Lonwork cabling is to forget to terminate the lines; this can cause a variety of unpredictable errors in the system;... -
Page 17: Connecting The Door
Connecting the door Door Connection (Using +14V Internal Power Supply) White switch Yellow LONWORKS POWER White switch Yellow JP1 JP2 Figure 11. Door Connection Using +14V Internal Power Supply Be aware that, even if the diode is already embedded in the unit, in some cases (long cable installed near the inputs cables) may be useful to add an external diode provided with the unit close to the relay device TK_S014 –... -
Page 18: Door Connection (Using +V External Power Supply)
Door Connection (Using +V External Power Supply) You may power the electro lock doors using an external isolated power supply (Voltage between 10 and 28VDC). DC OUT White AC IN switch Isolated Power supply Yellow LONWORKS POWER White switch Yellow JP1 JP2 Figure 12. -
Page 19: General Rules
For complete system details on this topic please refer: Temaline - installation in Harsh Environment whitepaper General rules In case of installation of the device in harsh environment apply the following rules: • All the cables must run into an isolated and dedicated track; •... -
Page 20: Activation
ACTIVATION This chapter shows only the preliminary steps required for the RTU activation. The complete configuration of the device is beyond the scope of this manual; please refer to EBI Temaline Interface - Temaline Access Control Configuration Guide for further details on these activities. Checking the communication between RTUA08 and TemaServer To do this verification procedure it is required to: •... -
Page 21: Collecting Device Information
Collecting device information The components enclosed in the packaging include a bar code label. The person responsible for installing the terminal must apply this label to the corresponding identification form, and indicate the location of the terminal in the appropriate box (see example in Table 5). The information collected can then be used for the RTU configuration on EBI Temaline application. -
Page 22: Technical Data
TECHNICAL DATA Parameter Value DC power supply 12V +/-15% 70mA [nominal internal] [up to 2.5A when driving power loads] Weight 0,2 Kg Dimensions (LxWxH) 105x93x61 mm Mounting Standard DIN/omega rail Operating temperature -10 ÷ 55°C Storage temperature -20 ÷ 70 °C Storage relative humidity 0 ÷... - Page 23 Power supply min : 12V – 15% = 10,2V Voltage drop max : 10,2 – 10 = 0,2V Cable resistance: Voltage drop / reader current max = 0,2 / 50mA = 4 Cable length (m: Resistance / (cable resistance / 1000) / 2 = = 4 / (52 /1000) / 2 = 38 mt Outputs to control LEDs and Type:...
-
Page 24: Regulation Compliance
REGULATION COMPLIANCE CE Compliance Company name: Honeywell S.r.l. Via Philips, 12 20052 Monza Italy Product name: TK_S014M (RTU A08M) Is in conformity with the European Union following harmonization legislation: Directives: Electromagnetic Compatibility Directive (2014/30/EU) General Product Safety Directive (2001/95/EC) RoHS EU Directive (2011/65/EU) -
Page 25: Rohs Compliance
In application of directive regarding waste electrical and electronic apparatus (WEEE), effective beginning 14 February 2014, Honeywell commits, when requested by the customer, to the collection, treatment, recovery, and disposal of apparatus produced. Customers in European Union are advised to dispose this product, at the end of its useful... -
Page 26: Meaning Of Graphical Symbols Used
MEANING OF GRAPHICAL SYMBOLS USED In compliance with “EN60950 Amendment 2 – Information Technology – Safety, General Requirements” this appendix shows the list of graphical symbols used in the product and their meanings. Symbol Meaning Located Keep away from rain Carton Box To indicate that the transport package shall be kept away from rain and in dry conditions.