Page 1 Notice Note that when converting this document from its original format to a .pdf file, some minor font and format changes may occur. When viewing and printing this document, we cannot guarantee that your specific PC or printer will support all of the fonts or graphics. Therefore, when you view the document, fonts may be substituted and your individual printer may not have the capability to print the document correctly.
Page 3 System Hardware Manual NWA-033622-001 Issue 1.0...
Page 5 NEC Unified Solutions, Inc. reserves the right to change the specifications, functions, or features at any time without notice. NEC Unified Solutions, Inc. has prepared this document for use by its employees and customers. The information contained herein is the property of NEC Unified Solutions, Inc.
Page 7: Regulatory
The UNIVERGE SV8100/SV8300 system provides what the customer needs today, and as business expands the system can be expanded to grow as well. The UNIVERGE SV8100/SV8300 system has a set of manuals that provide all the information necessary to install and support the system. This preface describes these manuals.
Page 8 SV8100/SV8300 chassis. Chapter 7 – Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline Terminals This chapter provides information about the UNIVERGE SV8100/SV8300 system digital and IP terminals in addition to the single line telephones, cordless telephones and wireless telephones. Chapter 8 – Installing SV8100/SV8300 Cordless Telephones This chapter provides information regarding cordless telephones that can be used in conjunction with the UNIVERGE SV8100/SV8300 system.
Page 9 Chapter 12 – Installing D Series i Telephones The UNIVERGE SV8100/SV8300 system supports several different Electra Elite IPK term II D Series i Multiline Terminals and an Attendant Console. This chapter describes each terminal and the console and provides instructions for attaching the terminals to the system and for wall mounting.
Page 10 THIS PAGE INTENTIONALLY LEFT BLANK...
Page 11: Table Of Contents
TABLE OF CONTENTS ___________________________________________________________________________________ Regulatory Chapter 1 Introduction to SV8100/SV8300 Section 1 General Information ..............1-1 Section 2 Equipment List ................1-5 Chapter 2 SV8100 System Specifications Section 1 General Information ..............2-1 Section 2 System Block Diagram ..............2-1 Section 3 Maximum System Capacities ............
Page 12 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Transmission, Network, and Control Specifications ....2-32 6.5.1 Transmission ................2-32 6.5.2 Network ..................2-32 6.5.3 Control ..................2-32 6.5.4 Electra Elite IPK Terminals and Equipment ......2-33 6.5.5 Series i Terminals ..............2-34 Dialing Specifications ..............2-34 6.6.1 Dial Pulse Address Signaling ...........2-34 6.6.2...
Page 13 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Section 2 System Block Diagram ..............3-1 Section 3 Maximum System Capacities ............. 3-5 System Configuration – SV8300 ..........3-7 Section 4 Licensing ..................3-14 Section 5 Power-Based Calculator Chart ..........3-17 Section 6 System Requirements And Specifications ......3-18 Cabling ..................
Page 14 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ 6.6.6 External Paging (Audio) ............3-26 6.6.7 External Tone Ringer/Night Chime Output .......3-27 6.6.8 SMDR Output ................3-27 6.6.9 PC Connection .................3-27 6.6.10 Relay Contact ................3-27 Battery Backup ................3-27 6.7.1 System Backup (Optional) ............3-27 6.7.2 Memory Backup ...............3-27 Weights and Dimensions ............3-28...
Page 15 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Constructing the Main Distribution Frame (MDF) ......4-4 Power Failure Transfer ............... 4-5 Fax CO Branch Connection ............4-5 Section 3 Installing the Chassis ..............4-6 Wall Mounting the 19” Chassis ............ 4-7 3.1.1 CHS2U-US Chassis Wall Mount Installation ......4-7 Floor Mounting the 19”...
Page 16 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ 3.5.9 Install Additional Blades ............4-41 3.5.10 Apply Power to the 19” Chassis ..........4-41 Section 4 Battery Connection ..............4-42 Installing the Internal Batteries ..........4-42 Installing the External Batteries ..........4-48 4.2.1 Floor Mounting the CHS LARGE BATT BOX ......4-48 4.2.2...
Page 17 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ 2.3.3 Selecting a Site for Installing the Telephones ......5-3 Constructing the Main Distribution Frame (MDF) ......5-3 Power Failure Transfer ..............5-4 Section 3 Installing the Chassis ..............5-5 Wall Mounting the 19” Chassis ............ 5-7 3.1.1...
Page 18 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ 3.5.6 Cable Connection between CPU Blades .........5-46 3.5.7 Install 19” Chassis Grounding ..........5-46 3.5.8 Install 19” Grounding on Multiple-Chassis (Optional) ....5-47 3.5.9 Install AC Power Cords ............5-48 3.5.10 Install AC Power Cords on Multiple-Chassis (Optional) ...5-49 3.5.11 Install Additional Blades ............5-49...
Page 19 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Section 2 Installation ................... 6-3 Installation and Safety Precautions ..........6-3 Installing an Extension or Trunk Blade ........6-4 2.2.1 Installing the Blades ..............6-4 2.2.2 Order of Installing Extension Blades .......... 6-4 2.2.3 Order of Installing Trunk Blades ..........6-6 2.2.3.1...
Page 20 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ 3.1.5 Connectors ................6-22 CC-CP00 (SV8300 Central Processing Unit) ......6-25 3.2.1 Description ................6-25 3.2.2 Installation ................6-28 3.2.3 Switch Settings .................6-29 3.2.4 LED Indications ................6-30 3.2.5 Connectors ................6-32 PZ-ME50 (Memory Expansion Daughter Board) .......6-35 3.3.1 Description ................6-35 3.3.2...
Page 21 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ PZ-8DLCB (Digital Station Daughter Board) ......6-53 4.2.1 Description ................6-53 4.2.2 Installation ................6-54 4.2.3 PZ-8DLCB Daughter Board Cable Connection ......6-54 CD-4LCA/ CD-8LCA (4-Port/8-Port Single Line Interface) ..6-56 4.3.1 Description ................6-57 4.3.2...
Page 22 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ 5.2.2 Installation ................6-76 5.2.3 Connectors ................6-76 CD-2BRIA (2 Basic Rate Interface) ...........6-78 5.3.1 Description ................6-78 5.3.2 Installation ................6-79 5.3.3 LED Indications ................6-80 5.3.4 Connectors ................6-81 PZ-2BRIA (2 Basic Rate Interface Daughter Board) ....6-82 5.4.1 Description ................6-83 5.4.2...
Page 23 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Section 6 Optional Blades ............... 6-100 CD-VM00 (Voice Mail and Server) .......... 6-100 6.1.1 Description ................6-100 6.1.2 Installation ................6-101 6.1.3 LED Indications ..............6-102 6.1.3.1 Active LED – Green ............6-102 6.1.3.2 Busy LED – Red ...............6-103 6.1.3.3...
Page 24 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ 6.4.1 Description ................6-113 6.4.2 Installation ................6-115 6.4.3 LED Indications ..............6-116 CD-ETIA (Gigabit PoE Switch) ..........6-117 6.5.1 Description ................6-117 6.5.2 Installation ................6-118 6.5.2.1 Stacking Architecture ............6-118 6.5.2.2 CD-CP00-USIP Address Assignment ......6-119 6.5.2.3 Group Formation .............. 6-119 6.5.2.4...
Page 25 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ 2.1.3 DTL-8LD-1 (BK) TEL/DTL-8LD-1 (WH) TEL ......7-7 2.1.4 DTL-12D-1 (BK) TEL/DTL-12D-1 (WH) TEL ......7-8 2.1.5 DTL-12PA-1 (BK) TEL ............... 7-9 2.1.6 DTL-24D-1 (BK) TEL/DTL-24D-1 (WH) TEL ......7-10 2.1.7 DTL-32D-1 (BK) TEL/DTL-32D-1 (WH) TEL ......7-11 Section 3 DT700 Series IP Multiline Terminals ........7-13...
Page 26 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Installing the Directory Card on the Multiline Terminal ....7-31 Installing a Numbered Keypad on the Multiline Terminal ..7-32 4.7.1 Installing the Numbered Keypad on a Multiline Terminal ..7-34 4.7.2 Configuring the Digital Telephone for the Numbered Keypad ..............7-36...
Page 27 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ 5.2.6 PANEL( )-L UNIT ..............7-63 5.2.7 WM-L UNIT Attached to Wall ........... 7-63 5.2.8 Release the WM-L UNIT ............7-65 5.2.9 WM-L UNIT Attached to Wall Plate .......... 7-66 5.2.10 Removing the Multiline Terminal from the Wall Mounted Plate.
Page 28 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ term ® Section 4 Cordless Lite II Terminal (DTH-4R-1) ......8-7 Selecting a Location ..............8-7 Controls and Indicators ..............8-7 Installation Precautions ..............8-10 Connecting the Telephone Cords ..........8-10 Applying Power to the Charging Unit .........8-11 Standard Wall Plate Mounting ...........8-12 Direct Wall Mounting ..............8-15...
Page 29 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Selecting a Location ..............8-31 Installation Precautions ............. 8-31 Connecting the Telephone Cords ..........8-32 Applying Power to the Charging Unit ......... 8-33 Mounting the Base to a Standard Wall Plate ......8-34 Mounting the Base Directly to the Wall ........8-37 Wall Mounting the Charging Unit ..........
Page 30 Headsets Used with Telephones ........8-58 term ® 8.3.1 Headset (MX250) ..........8-58 term ® 8.3.2 Cordless Phone Headset (M175) ......8-59 term ® 8.3.3 NEC Polaris SupraPlus™ .........8-60 term ® ® 8.3.4 NEC Polaris Mirage ........8-60 term ® ® 8.3.5 NEC Polaris TriStar ........8-61...
Page 31 Keypad Functions ..............10-3 Programming Options ..............10-3 Compliance ................10-4 Section 3 NEC Conference Max Plus ............10-5 Installing the Base Unit .............. 10-6 Connecting and Charging the Batteries ........10-6 Keypad Functions ..............10-6 Programming Options ..............10-7 Compliance ................
Page 32 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Chapter 11 Installing SV8100/SV8300 Optional Equipment Section 1 General Information ..............11-1 Section 2 PGD(2)-U10 ADP ................ 11-1 Using a PGD(2)-U10 ADP ............11-1 LED Indications ................11-2 Setting up PGD(2)-U10 ADP Connections ........11-2 Section 3 Background Music ..............11-10 Installing Background Music ............11-10...
Page 33 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Music on Hold ................11-24 Installing External Music on Hold ..........11-24 Section 9 Night Mode Selection ..............11-27 Night Mode Selector Switch ............ 11-27 Connecting a Night Mode Selector Switch ......11-27 Section 10 Telephone Labeling ..............11-27 10.1 DESI Printer Sheets ..............
Page 34 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ 11.5.2 Connection Configuration ............11-46 11.5.3 Connectors ................11-46 11.5.4 Package Contents ..............11-47 11.5.5 Hardware and Software Requirements ........11-47 11.5.6 Installation ................11-48 11.5.6.1 Location Preparation ............11-48 11.5.6.2 Set Up PC ................ 11-48 11.5.6.3 Install the 4-Port Digital Call Logging Unit ....... 11-49 11.5.6.4 Install the 4-Port Digital Call Logging Unit...
Page 35 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Section 12 Telephone Adapters ..............11-66 12.1 Using Adapters ................ 11-66 12.2 In-line Power Adapter (ILPA-R) ..........11-66 12.2.1 Conditions ................11-67 12.2.2 Installation ................11-68 12.3 ADA-L UNIT ................11-70 12.3.1 ADA-L UNIT Switch Settings ..........11-71 12.3.2 Installing the ADA-L UNIT ............
Page 36 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ DTR-2DT-1 TEL .................12-1 DTR-4D-1 TEL ................12-3 DTH-8-1/2 TEL ................12-4 DTH-8D-1/2 TEL ................12-5 DTH-16-1/2 TEL ................12-6 DTH-16D-1/2 TEL ..............12-7 DTH-16(BL)-1/2 TEL ..............12-8 DTH-16LD-1/2 TEL ..............12-9 DTH-32D-1 TEL ...............12-10 2.10 DCR-60-1( ) Console ..............12-11 Section 3 Connecting a Multiline Terminal to the System ....12-12...
Page 37 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Section 11 Wall Mounting Multiline Terminals ........12-22 11.1 Wall Mounting a Multiline Terminal using the Base Plate ..12-22 11.1.1 Adjusting the Hanger Hook ............ 12-22 11.1.2 Wall Mounting the Telephone ..........12-23 11.1.3 Removing the Wall Mounted Multiline Terminal from the Base Plate ...............
Page 38 Installing the External Microphone .........13-28 Add on Module (ADM) .............13-29 4.2.1 Connecting the Interface Unit ..........13-29 4.2.2 Wall Mounting ADM and Multiline Terminal ......13-31 NEC Push-to-Mute (PTM) or Push-to-Talk (PTT) Handset ..13-33 4.3.1 Description ................13-33 ___________________________________________________________________________________ xxviii Table of Contents...
Page 39 LIST OF FIGURES ___________________________________________________________________________________ Chapter 1 Introduction to SV8100/SV8300 Figure 1-1 Simplified SV8100 System Connectivity ..............1-2 Figure 1-2 Simplified SV8300 System Connectivity ..............1-2 Chapter 2 SV8100 System Specifications Figure 2-1 SV8100 System Block Diagram ................2-4 Figure 2-2 19”...
Page 40 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Figure 4-11 Secure CHS BASE UNIT with Anchor Bolts ............4-16 Figure 4-12 Install Rubber Feet ....................4-16 Figure 4-13 Install CHS2U JOINT BRACKET KIT ..............4-17 Figure 4-14 Install Rubber Feet ....................4-18 Figure 4-15 Install Metal Brackets with Screws ................4-18 Figure 4-16 Assemble Stand Mount with Screws ..............4-19...
Page 41 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Figure 4-44 19” Chassis Grounding Lug (Multiple-Chassis) ............. 4-40 Figure 4-45 Install the AC Power Cord ..................4-40 Figure 4-46 Install 19” AC Power Cords (Multiple-Chassis) ............. 4-41 Figure 4-47 Removing Battery Access Panel ................4-42 Figure 4-48 Removing Access Panel ..................
Page 42 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Figure 4-77 Removing the MPS7101 Screws ................4-61 Figure 4-78 Wiring Harness ......................4-63 Figure 4-79 19” Chassis Access Panel ..................4-64 Figure 4-80 Opening Chassis Access Panel (19” Chassis) ............4-65 Figure 4-81 Chassis Access Panel Removed ................4-65...
Page 43 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Figure 5-27 Attach Rubber Feet to CHS2U-US Chassis ............5-26 Figure 5-28 Assemble Stand Mount with Screws (CHS1U-US+CHS2U-USx2 Configuration) . 5-27 Figure 5-29 Assemble Stand Mount with Screws (CHS1U-US+CHS2U-USx3 Configuration) . 5-27 Figure 5-30 Attach Stand Mount Brackets to Chassis with Screws (CHS1U-US+CHS2U-USx2 Configuration) ............
Page 44 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Figure 5-59 Install 19” AC Power Cords (Multiple-Chassis) .............5-49 Figure 5-60 Removing Battery Access Panel ................5-50 Figure 5-61 Removing Access Panel ..................5-51 Figure 5-62 Securing Cable to Support Bracket ...............5-51 Figure 5-63 Securing Cable Support Bracket to Chassis ............5-52 Figure 5-64 Securing Batteries to Battery Tray .................5-52...
Page 45 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Figure 5-92 Removing Top Cover and Battery Bracket ............5-68 Figure 5-93 Mounting Batteries ....................5-69 Figure 5-94 Connecting Battery Cables ..................5-69 Figure 5-95 Install Top Cover of Battery Tray ................5-70 Figure 5-96 Connecting Battery Cable to Fuse Unit ..............
Page 46 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Figure 6-17 PZ-8DLCB Blade ....................6-53 Figure 6-18 CD-4LCA Blade .....................6-56 Figure 6-19 CD-8LCA Blade .....................6-57 Figure 6-20 Installing the PZ-4LCA Daughter Board ..............6-61 Figure 6-21 Installing the PZ-8LCE Daughter Board ..............6-62 Figure 6-22 CD-LTA Blade .......................6-66 Figure 6-23 CD-4COTB Blade ....................6-70...
Page 47 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Chapter 7 Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline Terminals Figure 7-1 DTL-2E-1 TEL ......................7-6 Figure 7-2 DTL-6DE-1 TEL .......................7-7 Figure 7-3 DTL-8LD-1 TEL .......................7-8 Figure 7-4 DTL-12D-1 TEL .......................7-9 Figure 7-5 DTL-12PA-1 TEL ....................7-10 Figure 7-6 DTL-24D-1 TEL .....................
Page 48 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Figure 7-32 Remove Plastic Panels ..................7-34 Figure 7-33 Removing Numbered Keypad from DT300/DT700 Series Terminal ....7-34 Figure 7-34 Install New Numbered Keypad into DT300/DT700 Series Terminal .....7-35 Figure 7-35 Install Plastic Panels ....................7-35 Figure 7-36 Adjust Height of DT300/DT700 Series Terminal ...........7-38...
Page 49 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Figure 7-65 Install Screw ......................7-57 Figure 7-66 DCL-60-1 CONSOLE .................... 7-58 Figure 7-67 Remove Side Panel from Multiline Terminal ............7-59 Figure 7-68 Secure Bracket to Multiline Terminal with Screws ..........7-59 Figure 7-69 Press Serial Cable into Groove ................
Page 50 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ term Figure 8-4 Cordless II ......................8-5 Figure 8-5 Connecting the Base Unit ..................8-6 term Figure 8-6 Cordless Lite II Controls and Indicators ............8-8 Figure 8-7 Connecting Base Unit to the Telephone Jack ............8-10 Figure 8-8 Connecting the Base Unit to the Multiline Terminal ..........8-11...
Page 51 Headset Cordless II ..................8-55 Figure 8-67 Cordless Headset (MX250) ................... 8-59 Figure 8-68 Cordless Headset (M175) ..................8-59 Figure 8-69 NEC Polaris Supraplus ..................8-60 Figure 8-70 NEC Polaris Mirage ....................8-60 ___________________________________________________________________________________ ___________________________________________________________________________________ System Hardware Manual System Hardware Manual...
Page 52 NEC Conference Max™ ..................10-2 Figure 10-2 NEC Conference Max Plus ..................10-5 Figure 10-3 NEC SIP Conference Installation ................10-9 Figure 10-4 Install Additional NEC SIP Conference Units ............10-9 Chapter 11 Installing SV8100/SV8300 Optional Equipment Figure 11-1 PGD(2)-U10 ADP ....................11-2 Figure 11-2 Remove Cover from PGD(2)-U10 ADP ..............11-3...
Page 53 Figure 11-45 In-Line Power Adapter ..................11-67 Figure 11-46 In-Line Power Adapter Switch Settings ............... 11-68 Figure 11-47 NEC Terminal Connection to an IEEE 802.3af PoE Switch ........ 11-69 Figure 11-48 ADA-L UNIT ......................11-71 Figure 11-49 Separate Tilt Leg from Leg Support ..............11-72 Figure 11-50 Bottom Option Interface Knockout ..............
Page 54 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Figure 11-55 Separate Tilt Leg from Leg Support ..............11-77 Figure 11-56 Bottom Option Interface Knockout ...............11-78 Figure 11-57 Install APR-L UNIT ....................11-78 Figure 11-58 Ferrite Bead with APR Adapter ................11-79 Figure 11-59 PSA-L UNIT ......................11-80 Figure 11-60 PSA-L UNIT Connections ..................11-81...
Page 55 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Figure 12-14 Connecting the Line Cord and AC Adapter when Installing a DCR Attendant Console ..............12-13 Figure 12-15 Attendant Console and Multiline Terminal ............12-14 Figure 12-16 Adjusting the LCD on a Multiline Terminal ............12-14 Figure 12-17 Installing Line Card and Plastic Panel on a Multiline Terminal ......
Page 56 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ term Chapter 13 Installing D Series i Optional Equipment Figure 13-1 Raising the Base Plate ..................13-1 Figure 13-2 Removing the Multiline Terminal Base Plate ............13-2 Figure 13-3 Modifying Base Plate for Adapter Installation ............13-3 Figure 13-4 AC-2R/AC-3R Unit (AC Adapter) ................13-4...
Page 57 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Figure 13-32 Installing the Connector Plate ................13-31 Figure 13-33 Installing Base Units on the Wall ................. 13-32 Figure 13-34 NEC PTM or PTT Handset .................. 13-33 ___________________________________________________________________________________ ___________________________________________________________________________________ System Hardware Manual System Hardware Manual...
Page 58 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ THIS PAGE INTENTIONALLY LEFT BLANK ___________________________________________________________________________________ xlviii List of Figures...
Page 59 LIST OF TABLES ___________________________________________________________________________________ Table R-1 Battery Types and Quantities for Chassis and Blades ........... R-7 Chapter 1 Introduction to SV8100/SV8300 Table 1-1 Chassis Equipment List ................... 1-5 Table 1-2 Chassis Installation Equipment List ................. 1-5 Table 1-3 Battery Mount Equipment List ................. 1-5 Table 1-4 Blade Equipment List ....................
Page 60 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Table 2-17 Power Consumption ....................2-30 Table 2-18 SV8100 Weights and Dimensions .................2-37 Table 2-19 Tone Patterns ......................2-42 Table 2-20 Multiline Terminal LED Flash Pattern ..............2-43 Table 2-21 Traffic Capacity ......................2-44 Chapter 3 SV8300 System Specifications Table 3-1 List of Abbreviations ....................3-1...
Page 61 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Chapter 5 Installing the SV8300 Chassis Table 5-1 Power Failure Transfer Connections ............... 5-4 Table 5-2 PZ-BS10/PZ-BS11 Connector Pin-Out ..............5-37 Table 5-3 Battery Capacity of External Battery ..............5-64 Table 5-4 Battery Capacity of External Battery ..............5-65...
Page 62 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Table 6-27 PZ-8DLCB CN401 Connection ................6-55 Table 6-28 CD-4LCA/CD-8LCA Maximum Upgrade Capacities ..........6-58 Table 6-29 CD-4LCA/CD-8LCA LED Indications ..............6-59 Table 6-30 CD-4LCA/CD-8LCA RJ-61 Cable Connector Pin-Outs .........6-60 Table 6-31 CD-4LCA/CD-8LCA Maximum Upgrade Capacities ..........6-63 Table 6-32 PZ-4LCA/PZ-8LCE/ RJ-61 Cable Connector Pin-Outs ........6-65...
Page 63 UNIVERGE SV8100/SV8300 Issue 1.0 ___________________________________________________________________________________ Table 6-60 CD-RTB LED Indications ..................6-116 Table 6-61 CD-ETIA LED Indications ..................6-120 Table 6-62 MDF Cable Colors ....................6-122 Table 6-63 MDF Cable Connections (Station) ............... 6-122 Table 6-64 MDF Cable Connections (Trunk) ................. 6-124...
Page 64 Issue 1.0 UNIVERGE SV8100/SV8300 ___________________________________________________________________________________ Chapter 11 Installing SV8100/SV8300 Optional Equipment Table 11-1 PGD(2)-U10 ADP LED Indications ................11-2 Table 11-2 PGD(2)-U10 ADP S3 – S6 Jumper Settings ............11-4 Table 11-3 ADA-L Unit Switch Settings .................11-71 Table 11-4 RJ-61 Cable Connector ..................11-89...
Page 65: Section 1 General Information
The telephone company may make changes in its technical operations and procedures. When such changes affect the compatibility or use of the UNIVERGE SV8100/SV8300 system, the telephone company is required to give adequate notice of the changes in order for you to maintain uninterrupted service.
Page 66 If equipment malfunctions, all repairs must be performed by an authorized agent of NEC Unified Solutions, Inc. or by NEC Unified Solutions, Inc. The user requiring service is responsible for reporting the need for service to an NEC Unified Solutions, Inc. authorized agent or to NEC Unified Solutions, Inc. Regulatory...
Page 67 The consumer/purchaser/supplier instructions accompanying this equipment and/or software features must contain the following notice: The software contained in the UNIVERGE SV8100/SV8300 to allow user access to the network must be upgraded to recognize newly established network area codes and exchange codes as they are placed into service.
Page 68 Issue 1.0 UNIVERGE SV8100/SV8300 Routed to a recorded announcement that can be administered by the Customer Premise Equipment (CPE) user. Routed to a dial prompt. This equipment returns answer supervision on all DID calls forwarded to the Public Switched Telephone Network (PSTN). Permissible exceptions are: A call is unanswered.
Page 69 Issue 1.0 HEARING AID COMPATIBILITY NEC Multiline Terminals and NEC Single Line Telephones that are provided for this system are hearing aid compatible. The manufacturer of other Single Line Telephones for use with the system must provide notice of hearing aid compatibility to comply with FCC rules that now prohibit the use of non-hearing aid compatible telephones.
Page 70 Issue 1.0 UNIVERGE SV8100/SV8300 SAFETY INFORMATION This equipment has been certified by Canadian Standards Association and found to comply with all applicable requirements: CAN/CSA C22.2 No. 0-M – General Requirements – Canadian Electrical Code, Part II CAN/CSA C22.2 No. 60950-1-03 – Safety of Information Technology Equipment – Part l: General Requirements UL 60950-1-SAFETY, 1st Edition –...
Page 71: Table R-1 Battery Types And Quantities For Chassis And Blades
Industrie Canada. BATTERY DISPOSAL The UNIVERGE SV8100/SV8300 system includes the batteries listed below. When disposing of these batteries, Chassis, and/or Blades, you must comply with applicable federal and state regulations regarding proper disposal procedures.
Page 72 For Ni-Cd batteries, you can also call 1-800-8-BATTERY when further information is required. The packaging for the UNIVERGE SV8100/SV8300 system contains the following labels regarding proper disposal. Regulatory...
Page 73 UNIVERGE SV8100/SV8300 Issue 1.0 PRODUCT PACKAGE LABELING CONTAINS NICKEL-CADMIUM BATTERY. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. MUST NOT BE DISPOSED OF IN MUNICIPAL WASTE. Ni-Cd CONTAINS SEALED LEAD BATTERY. BATTERY MUST BE RECYCLED. MUST NOT BE DISPOSED OF IN MUNICIPAL WASTE.
Page 74 For an overview of the supported features, refer to the detailed documentation that comes with this system, contact your local NEC Philips representative or the support desk of NEC Philips Unified Solutions.
Page 75 This product uses Lithium batteries. Do not use any other type. For an overview of the location of batteries used in these systems, the battery replacement or removal instructions, please refer to the UNIVERGE SV8100/SV8300 System Hardware Manual. System Hardware Manual...
Page 76 Issue 1.0 UNIVERGE SV8100/SV8300 - - NOTES - - R-12 Regulatory...
Page 77: Introduction To Sv8100/Sv8300
Introduction to SV8100/SV8300 ENERAL NFORMATION ECTION The SV8100/SV8300 is a full-featured IP based communications system providing a rich feature set of existing system, with pure Voice over IP (VoIP) communications, across corporate Local and Wide Area Networks Chapter (LAN and WAN). The DT700 series telephones provide a converged infrastructure at the desktop, with a 10Base-T/100Base-TX connection to the LAN and built-in hub for a PC connection to the telephone itself.
Page 78: Figure 1-1 Simplified Sv8100 System Connectivity
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 1-1 Simplified SV8100 System Connectivity Figure 1-2 Simplified SV8300 System Connectivity 1 - 2 Introduction to SV8100/SV8300...
Page 79 UNIVERGE SV8100/SV8300 Issue 1.0 Highlights of the UNIVERGE SV8100/SV8300 are as follows: Pure IP System capable TDM configuration The SV8100/SV8300 supports both pure IP switching (peer-to-peer connections) and Time Division Switching. The pure IP switching is provided for communications between DT700 series telephones and for CCIS / Remote Unit connections with other SV8100/SV8300/SV7000.
Page 80 Issue 1.0 UNIVERGE SV8100/SV8300 High Density Legacy Line/Trunk Blades Major legacy line/trunk blades used in SV8100/SV8300 are provided with main blade + daughter blade architecture. When the main blade is mounted only in an initial supply, line/trunk interfaces can be easily expanded by adding the daughter blade.
Page 81: Table 1-1 Chassis Equipment List
UNIVERGE SV8100/SV8300 Issue 1.0 QUIPMENT ECTION The following tables list all equipment for the SV8100/SV8300 systems. The product code column indicates whether the equipment is available for the SV8100 product line only (SV8100), for SV8300 product line only (SV8300) or is common for both SV8100/ SV8300 product lines (SV8100/SV8300).
Page 82: Table 1-4 Blade Equipment List
Issue 1.0 UNIVERGE SV8100/SV8300 Table 1-3 Battery Mount Equipment List (Continued) Stock Number Equipment Name Equipment Description Product Code 670505 CHS LARGE BATT BOX Long Term Battery Box for CHS1U-US and SV8100/SV8300 CHS2U-US Chassis Cable between batteries – 9.06in/230mm Fuse Unit to Batteries – 18.11ln/460mm Cable from chassis to battery box –...
Page 83: Table 1-5 Cable Equipment List
UNIVERGE SV8100/SV8300 Issue 1.0 Table 1-4 Blade Equipment List (Continued) Stock Number Equipment Name Abbreviations Equipment Description Product Code 670113 PZ-4LCA LCDB 4-port Single Line Telephone Interface on SV8100/SV8300 CD-4LCA and CD-8LCA 670114 CD-8LCA 8-port Single Line Telephone Interface SV8100/SV8300...
Page 84: Table 1-6 Digital Multiline Terminal (Dt300 Series) Equipment List
Issue 1.0 UNIVERGE SV8100/SV8300 Table 1-5 Cable Equipment List (Continued) Stock Number Equipment Name Equipment Description Product Code 670529 AC CORD AC Power Cable for US SV8100/SV8300 670530 CHS2U BATT CA INT CHS2U-US Battery Cable for Internal SV8100/SV8300 Battery 2U Chassis Cable A –...
Page 85: Table 1-7 Ip Multiline Terminal (Dt700 Series) Equipment List
UNIVERGE SV8100/SV8300 Issue 1.0 Table 1-7 IP Multiline Terminal (DT700 Series) Equipment List Stock Number Equipment Name Equipment Description Product Code 690000 ITL-2E-1 (BK) TEL Economy IP 2-button Telephone (No SV8100/SV8300 Display) 690001 ITL-6DE-1 (BK) TEL Economy IP 6-button Display Telephone...
Page 86 Issue 1.0 UNIVERGE SV8100/SV8300 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Stock Number Equipment Name Equipment Description Product Code 680652 DESI ITL/DTL-12D (25 PKG) DESI Sheet for Value 12-button Display SV8100/SV8300 Telephone (2 Labels per Sheet) 680653 DESI ITL/DTL-8LK (25 PKG) DESI Sheet for 8-button Line Key (2 Labels...
Page 87 UNIVERGE SV8100/SV8300 Issue 1.0 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Stock Number Equipment Name Equipment Description Product Code 680714 LKPANEL(2BTN)-L (BK) Spare Plastic Cover Kit (2-button) (BK) SV8100/SV8300 UNIT 680715 LKPANEL(6BTN)-L (BK) Spare Plastic Cover Kit (6-button) (BK)
Page 88 Issue 1.0 UNIVERGE SV8100/SV8300 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Stock Number Equipment Name Equipment Description Product Code 680741 Panel (Clear-VLCD)-L UNIT Color Side Panel for Value Telephone LCD SV8100/SV8300 (Clear) 680742 Panel (Clear-SLCD)-L UNIT Color Side Panel for Sophisticated...
Page 89 UNIVERGE SV8100/SV8300 Issue 1.0 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Stock Number Equipment Name Equipment Description Product Code 690618 HandsetCord(12FT)-L (BK) Spare Handset Cord 12 Feet SV8100/SV8300 690619 HandsetCord(12FT)-L (WH) 690620 HandsetCord(25FT)-L (BK) Spare Handset Cord 25 Feet...
Page 90 Issue 1.0 UNIVERGE SV8100/SV8300 - - NOTES - - 1 - 14 Introduction to SV8100/SV8300...
Page 91: System Block Diagram
SV8100 System Specifications ENERAL NFORMATION ECTION This chapter provides detailed specifications for the SV8100 system technician. The technician should review this information carefully before installing the system. Chapter YSTEM LOCK IAGRAM ECTION Figure 2-1 SV8100 System Block Diagram shows the Blades that can be installed in the chassis and the number of channels supported when the Blade is installed.
Page 92 Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-1 List of Abbreviations (Continued) Abbreviation Description Direct Inward Dialing DIOP DID/OPX Blade Digital Multiline Terminal Interface Blade DLCB Expansion Digital Multiline Terminal Interface Blade on DLC Device Registration Server (on CPU) Direct Station Selection Console...
Page 93 UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-1 List of Abbreviations (Continued) Abbreviation Description Property Management System Primary Rate Interface Primary Rate Interface Blade Personal Station PSTN Adapter (analog) Packet Voice Application Router Blade SERIAL Serial Port (on CPU) Single Line Telephone...
Page 94 Issue 1.0 UNIVERGE SV8100/SV8300 Figure 2-1 SV8100 System Block Diagram 2 - 4 SV8100 System Specifications...
Page 95: Maximum System Capacities
UNIVERGE SV8100/SV8300 Issue 1.0 AXIMUM YSTEM APACITIES ECTION The CHS2U-US is a compact 19” chassis that has six universal slots, one expansion slot and one MPS7101 (power supply unit). When the CD-CP00-US is installed in the first CHS2U-US, it is referred to as the Controlling Chassis. Additional chassis, referred to as Expansion Chassis, can be installed to increase the capacity of the system to meet the customer’s business needs.
Page 96: System Configuration - Sv8100
Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-2 SV8100 Maximum System Capacities – Trunks/Ports/Channels 19” Chassis System Number of: Maximum (6 Slots) (12 Slots) (18 Slots) (24 Slots) 16 channels Voice Mail Channels on CPU 1 channel V90 Modem 1 = Maximum 80 Digital Terminals per 19” chassis due to power consumption System Configuration –...
Page 97 UNIVERGE SV8100/SV8300 Issue 1.0 6 Slots 18 Slots 24 Slots IP Connection Figure 2-2 19” Controlling and Expansion Chassis System Hardware Manual 2 - 7...
Page 98: Table 2-3 Maximum System Capacities - Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-3 Maximum System Capacities – Chassis shows the maximum number of chassis and related equipment that can be installed in a system. Table 2-3 Maximum System Capacities – Chassis 19” 19” 19” Chassis Hardware Chassis...
Page 99: Table 2-4 Maximum System Capacities - Blades
UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-4 Maximum System Capacities – Blades shows the maximum number for each blade that can be installed in a system. This is determined by the maximum blade configuration allowed. When installing single line sets, DISA, or tie lines, CPU circuits must be allocated for DTMF receivers.
Page 100: Chapter 2 Sv8100 System Specifications
Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-4 Maximum System Capacities – Blades (Continued) 19” 19” 19” Chassis Hardware Chassis Chassis without Networked with CPU Comments Chassis Number of Slot(s) for Interface 5 Slots 6 Slots 23 Slots Package PZ-8DLCB Maximum of 80...
Page 101 UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-4 Maximum System Capacities – Blades (Continued) 19” 19” 19” Chassis Hardware Chassis Chassis without Networked with CPU Comments Chassis Number of Slot(s) for Interface 5 Slots 6 Slots 23 Slots Package Optional Blades: CD-PVAA –...
Page 102: Table 2-5 Daughter Board Combinations
Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-5 Daughter Board Combinations shows each blade and associated daughter board combinations. The daughter boards that can be mounted on specific blades are indicated by a checkmark. For example, the CD-LTA can have a PZ-2BRIA or the PZ-4COTF daughter board mounted.
Page 103: Licensing
UNIVERGE SV8100/SV8300 Issue 1.0 ICENSING ECTION Table 2-6 System Licenses provides a list of the licensing available with the system. Table 2-6 System Licenses License Function Description System: LK-SYS-UPG FM 65 TO 256 PORT-LIC System Ports - 256 Port This system license supports a maximum of License 256 System Port Licenses.
Page 104 Supports 16 system SIP or H.323 Trunks. This license is NOT REQUIRED to support the CCISOIP Trunking Feature. LK-SYS-IP-TERMINAL-1-LIC NEC SIP Client - One license One NEC SIP Client - supports NEC MLT SIP Terminal and/or NEC Softphone (SP310). LK-SYS-IP-TERMINAL-4-LIC...
Page 105 Desktop Suite (Assistant, Attendant, SP310) Part No. 670829 AK DESKTOP PC APP-CD. The NEC Softphone (SP310) client license and NEC SIP Client license is provided with each PC Assistant client license. LK-DESKTOP SUITE- PC ASSISTANT4-LIC Desktop Suite PC Assistant Four Desktop Suite - PC Assistant Client...
Page 106 Desktop Suite (Assistant, Attendant, SP310) Part No. 670829 AK DESKTOP PC APP-CD. The NEC Softphone (SP310) client license and NEC SIP Client license is provided with each PC Assistant client license. LK-DESKTOP SUITE- PC ATTENDANT1-LIC Desktop Suite PC Attendant One Desktop Suite - PC Attendant Client...
Page 107 LK-DESKTOP SUITE-ENHANCE PKG32-LIC Desktop Suite Enhancement 32 Desktop Suite - Enhancement Pkg client Pkg Client - 32 license license used in conjunction with NEC Desktop Suite (Assistant, Attendant, SP310) Part No. 670829 AK DESKTOP PC APP-CD provides enhanced features (White board, File Transfer, File Sharing, Instant Msg).
Page 108 Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-6 System Licenses (Continued) License Function Description LKS-VM-INMAIL2-LIC VM8000 InMail Port - Two Two Port license (VM8000 InMail) - license Approximately 33 hours of storage and requires stock no. 670831 AKS InMail-512M - APP CF Supports a maximum of 16 Dynamic VRS Ports and/or eight Dynamic InMail ports.
Page 109 UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-6 System Licenses (Continued) License Function Description LKS-UMS-CLIENT32-LIC UM8000 Mail View App 32 Client View App Session UMS8000 Mail. Session - 32 license Supports client, View Mail, View Call Plus, VMM (outlook), VML (Lotus Notes), VMG (GroupWise) and Web Mailbox Manager.
Page 110 Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-6 System Licenses (Continued) License Function Description LKS-UMS-HOTEL-PMS-LIC UM8000 Mail Hospitality/ Hospitality and PMS activation license PMS license LKS-UMS-HOTEL-LANGUAGE-LIC UM8000 Mail Hospitality One hospitality language activation license Language - One license LKS-UMS-AMIS-PLUS-LIC UM8000 Mail AMIS/Plus Net...
Page 111 UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-6 System Licenses (Continued) License Function Description LKS-CA-TRAFFIC ANALYSIS-LIC SMB8000 Communications Communication Analyst Traffic Analysis – Analyst - Traffic analysis Enables understanding of trunk utilization and what-if analysis for trunk capacity and bandwidth optimization. LKS-CA-PMS INTEGRATION-LIC SMB8000 Communications Communication Analyst PMS Integration –...
Page 112 LKS-DESKTOP SUITE-SOFTPHONE1-LIC Desktop Suite Soft Phone One Desktop Suite - Soft Phone (SP310) (SP310) Client - One license client license fused in conjunction with NEC Desktop Suite (Assistant, Attendant, SP310) Part No. 670829 AKS DESKTOP PC APP-CD. The NEC Softphone SP310 requires a NEC SIP client license stock number 670716 LK-SYS-IP-TERMINAL-1-LIC.
Page 113: Table 2-7 Board Power Factor
OWER ASED ALCULATOR HART ECTION The Univerge SV8100 system uses two types of power factors. For a single chassis chart refer to Table 2-7 Board Power Factor. For the maximum number of specific blades per package, see Table 2-8 Maximum Number of Package Installed.
Page 114: Table 2-10 Ip Terminal Power Chart
Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-9 Terminal Power Factor Terminal Power Factor 19 inch Chassis =<80 Item Power Factor DTL-24D-1 TEL DTL-8LD-1 TEL ADA-L UNIT APR-L UNIT Power Save Adapter 8LK-L UNIT DCL-60-1 CONSOLE ITL-320C-1 TEL ITL-24D-1 TEL ITL-2E-1 TEL...
Page 115: Table 2-11 Ieee802.Af Class Specifications
UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-10 IP Terminal Power Chart (Continued) Label Indication IEEE802. Maximum Current Without Options (Maximum Current with All Options) Terminal Class 48VDC 24VDC 48VDC 24VDC – – ITL-24PA-1 TEL Class 2 130mA 6.2W 235mA 5.6W 0.0W 0.0W...
Page 116: Cabling
Issue 1.0 UNIVERGE SV8100/SV8300 YSTEM EQUIREMENTS AND PECIFICATIONS ECTION Cabling This section provides cabling requirements and specifications for various equipment used in the SV8100 system. Figure 2-3 Connecting the DLC Using Twisted 2-Pair Cable is a diagram of the chassis connected with each of the multiline terminals and single line telephones by a separate twisted 1-pair cable or 2-pair cable (only for Multiline Terminals).
Page 117 UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-12 DT300 Series Loop Resistance and Cable Length (Continued) By Twisted 1-Pair Cable Terminal or Adapter (without AC Adapter) 24 AWG DTL-12D-1 (BK) TEL 1,969 ft (600m) DTL-12D-1 (WH) TEL DTL-24D-1(BK) TEL 1,969 ft (600m)
Page 118 Issue 1.0 UNIVERGE SV8100/SV8300 term term Table 2-14 D Series i or D IP Terminal Loop Resistance and Cable Length Maximum Maximum By Twisted By Twisted By Twisted By Twisted Loop Loop 1-Pair Cable 2-Pair Cable 1-Pair Cable 2-Pair Cable...
Page 119: Power Requirements
UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-16 Cabling Requirements Connected Equipment Cable Music on Hold and Background Music Sources Hi-Fi Shielded Audio Cable External Amplifier Hi-Fi Shielded Audio Cable ITL Cabling Cat 5 Straight Data Network Cable – 328.1 ft (100m) maximum distance.
Page 120: Power Supply Consumption
Issue 1.0 UNIVERGE SV8100/SV8300 KWh @ AC Input I x 120V/1000: Base chassis=0.324 KWh, Expansion chassis=0.324 KWh, total 1.296 KWh BTU (KWh x 3413): Base chassis= , Expansion 1106 BTU chassis= , total 1106 BTU 4424 BTU Double Pole/Neutral Fusing (power supply fuses are located at both the L and N side).
Page 121: Outside Line Types
Operating Humidity: 20 ~ 95% RH (non-condensing) Recommended Long Term Humidity: 10 ~ 95% RH Outside Line Types The following outside lines can be used with the UNIVERGE SV8100/SV8300 system. 2-wire, Loop Start or Ground Start Trunks – SV8300 only 2-wire, 2-way DID Lines (Dial Pulse or DTMF) –...
Page 122 Network Time Division Multiplexing (TDM) allows transmission of data and voice simultaneously over one communications medium. The specifications that the UNIVERGE SV8100/SV8300 system uses for switching, clock, data bus, and timeframe are shown below. TDM Switching: PCM (µ Law) TDM Clock: 2.048 MHz TDM Data Bus: 8 bit TDM Timeframe: 125 µs.
Page 123 UNIVERGE SV8100/SV8300 Issue 1.0 6.5.4 Electra Elite IPK Terminals and Equipment The voltage, current, and ring signal for the Electra Elite IPK Multiline Terminals, Single Line Telephone equipment, and AP(A)-R/AP(R)-R Units are listed below: Multiline Terminal Voltage: -11 ~ -26 Vdc...
Page 124 Dual-Tone Multifrequency (DTMF) Address Signaling DTMF signaling includes push button or Touchtone dialing. When a key on a telephone is pushed, two tones (one high frequency and one low frequency) are provided. In the UNIVERGE SV8100/SV8300 system, the following DTMF specifications are used. Frequencies Two sinusoidal frequencies are provided, one from the high frequency group and one from the low frequency group.
Page 125 UNIVERGE SV8100/SV8300 Issue 1.0 Rise Time: Within 5 ms. Duration of Dual Frequency Signal: 110 ms. default/60 ms. minimum Interdigital Time: 140 ms. default/45 ms. minimum Nominal High Group Frequencies (Hz) 1209 1336 1477 Nominal Low Group Frequencies (Hz) 6.6.3...
Page 126 6.6.10 Relay Contact All Relay Contact Ratings: 500 mA, 24Vdc Battery Backup The UNIVERGE SV8100/SV8300 system has battery backup functions for system backup and for memory backup. 6.7.1 System Backup (Optional) During a power failure, the system can be backed up using the...
Page 127: Table 2-18 Sv8100 Weights And Dimensions
UNIVERGE SV8100/SV8300 Issue 1.0 Weights and Dimensions Table 2-18 SV8100 Weights and Dimensions on page 2-37 shows the shipping weight, height, width and depth of each SV8100 digital multiline term terminal, IP multiline terminal, D , Series i multiline terminal, chassis, assorted blades and adapters.
Page 128 Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-18 SV8100 Weights and Dimensions (Continued) Shipping Unit Height Width Depth Weight CD-16DLCA 7.831 oz 1.89 in 9.45 in 7.68 in (0.222 kg) (48 mm) (240 mm) (195 mm) CD-4COTB 6.35 oz 1.89 in 9.45 in 7.68 in...
Page 129 UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-18 SV8100 Weights and Dimensions (Continued) Shipping Unit Height Width Depth Weight CHS L BATT BOX RACK MOUNT BRACKET 352.7 oz 18.5 in 14.6 in 2.76 in (10 kg) (470 mm) (370 mm) (70 mm) CHS2U INT BATT SET 95.24 oz...
Page 130 Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-18 SV8100 Weights and Dimensions (Continued) Shipping Unit Height Width Depth Weight ITL-12BT-1 (BK) TEL 45.6 oz 4.29 in 7.59 in 10.16 in (1.3 kg) (109 mm) (193 mm) (258 mm) ITL-12D-1 (BK) TEL 42.33 oz 4.41 in...
Page 131: Table 2-19 Tone Patterns
6.8.1 Tone Patterns Table 2-19 Tone Patterns lists the frequency and the pattern for the tones. Tones are used to inform UNIVERGE SV8100/SV8300 station users of system functions such as dial tone, busy tone, or ringback tone. 6.8.2 Multiline Terminal LED Flash Patterns The UNIVERGE SV8100/SV8300 system has several colored LEDs installed.
Page 132 Issue 1.0 UNIVERGE SV8100/SV8300 Table 2-19 Tone Patterns System Tone Frequency (Hz) Intermit Cycle (Fixed) (Fixed) (Default) 0.5 sec Busy Tone 480/620 60 IPM 0.5 sec 0.5 sec Call Waiting Tone 60 IPM 0.5 sec 0.25 sec Second Dial Tone...
Page 133: Table 2-20 Multiline Terminal Led Flash Pattern
UNIVERGE SV8100/SV8300 Issue 1.0 Table 2-20 Multiline Terminal LED Flash Pattern Condition Color Flash Patterns I-Use Green Busy Incoming Call I-Hold Green Line Key Call Hold Hold Recall Green Transfer Recall Green Live Monitoring Mode Green Message Waiting on Line Key...
Page 134: Table 2-21 Traffic Capacity
Issue 1.0 UNIVERGE SV8100/SV8300 RAFFIC APACITY ECTION Table 2-21 Traffic Capacity provides information about the traffic capacity for the basic system package and expanded system package. Table 2-21 Traffic Capacity Basic System Expanded System Traffic Capacity Package Package Traffic Capacity...
Page 135: Table 3-1 List Of Abbreviations
SV8300 System Specifications ECTION ENERAL NFORMATION This chapter provides detailed specifications for the SV8300 system technician. The technician should review this information carefully before installing the system. Chapter ECTION YSTEM LOCK IAGRAM Figure 3-1 SV8300 System Block Diagram shows the Blades that can be installed in the chassis and the number of channels supported when the Blade is installed.
Page 136 Issue 1.0 UNIVERGE SV8100/SV8300 Table 3-1 List of Abbreviations (Continued) Abbreviation Description DLCB Expansion Digital Multiline Terminal Interface Blade on DLC Device Registration Server (on CPU) Direct Station Selection Console Digital Trunk Interface Digital Tone Generator (on CPU) ETHERNET Ethernet Port (on CPU)
Page 137 UNIVERGE SV8100/SV8300 Issue 1.0 Table 3-1 List of Abbreviations (Continued) Abbreviation Description Personal Station PSTN Adapter (analog) In-Skin Router Blade RS1/RS2 Serial Port (on CPU) Single Line Telephone SMDR Station Message Detail Recording SWHUB Power over Ethernet Hub TDSW Time Division Switch (on CPU)
Page 138: Figure 3-1 Sv8300 System Block Diagram
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 3-1 SV8300 System Block Diagram 3 - 4 SV8300 System Specifications...
Page 139: Table 3-2 Sv8300 Maximum System Capacity
UNIVERGE SV8100/SV8300 Issue 1.0 AXIMUM YSTEM APACITIES ECTION The CHS1U-US is a single slot, 19” chassis holding the CC-CP00 blade and one PSU. The CHS1U-US can be expanded by adding a maximum of three additional CHS2U-US chassis (referred to as a Unit), increasing the capacity of the system to meet the customer’s business needs.
Page 140: Chapter 3 Sv8300 System Specifications
Issue 1.0 UNIVERGE SV8100/SV8300 Table 3-2 SV8300 Maximum System Capacity (Continued) 1 Unit System Maximum Units Units Units Item Standalone Remote Unit Physical ISDN Terminal (BRI) Port ZT interface (CSI) In-Skin UMS IP Multiline 1024 1024 1296 1500 1500 Terminal...
Page 141: Figure 3-2 System Configuration Example (Ip-Oriented System)
UNIVERGE SV8100/SV8300 Issue 1.0 Table 3-2 SV8300 Maximum System Capacity (Continued) 1 Unit System Maximum Units Units Units Item Standalone Remote Unit DTMF Receiver Caller ID Sender 3/4-Party Conference 2U = Expansion Chassis term = When using D Series i with APR (Dual Port Mode), the physical ports for analog station shown in parenthesis are required in addition to the physical ports for Multiline Terminal.
Page 142 Issue 1.0 UNIVERGE SV8100/SV8300 One Unit = Maximum of 324 Ports UNIT #1 (Main) UNIT #2 UNIT #4 UNIT #3 Four UNIT = Maximum of 1296 Ports Figure 3-3 System Configuration Example (TDM-Oriented System SV8300 (Main Unit) SV8300 SV8300 SV8300...
Page 143: Table 3-3 Maximum System Capacity - Chassis
UNIVERGE SV8100/SV8300 Issue 1.0 Table 3-3 Maximum System Capacity – Chassis shows the maximum number of chassis and related equipment that can be installed in a system. Table 3-3 Maximum System Capacity – Chassis 1 Unit System Maximum Units Units...
Page 144: Table 3-4 Maximum System Capacity - Blades
Issue 1.0 UNIVERGE SV8100/SV8300 Table 3-3 Maximum System Capacity – Chassis (Continued) 1 Unit System Maximum Units Units Units Equipment Remote 2Ux1 2Ux2 2Ux3 2Ux6 2Ux9 2Ux12 Standalone Unit CHS2U JOINT BRACKET CHS2U BLANK SLOT COVER KIT CHS1U BLNK SLOT...
Page 145: Table 3-5 Daughter Blade Combinations
UNIVERGE SV8100/SV8300 Issue 1.0 Table 3-4 Maximum System Capacity – Blades (Continued) 1 Unit System Maximum Units Units Units Equipment Standalone Remote Unit CD-16DLCA Trunk Blades: CD-2BRIA PZ-2BRIA CD-4COTB PZ-4COTF CD-4DIOPA CD-4ODTA CD-PRTA CD-CCTA Option Blades: CD-ETIA CD-RTB CD-VM00 2U = Expansion Chassis N/A = Not Available = accommodated at CPU blade of main unit (UNIT#1) only.
Page 146: Table 3-6 Maximum System Capacity - Terminals
Issue 1.0 UNIVERGE SV8100/SV8300 Table 3-5 Daughter Blade Combinations (Continued) Daughter Blades Blades PZ-2BRIA PZ-4COTF PZ-4LCA PZ-8DLCE PZ-8DLCB CD-2BRIA – – – – – = Does not apply = Does apply Table 3-6 Maximum System Capacity – Terminals shows the maximum number of terminals that can be installed in a system.
Page 147: Table 3-7 Maximum System Capacity - Optional Equipment
UNIVERGE SV8100/SV8300 Issue 1.0 Table 3-7 Maximum System Capacity – Optional Equipment shows the maximum number of optional equipment that can be installed in a system. Table 3-7 Maximum System Capacity – Optional Equipment 1 Unit System Maximum Units Units...
Page 148: Table 3-9 System Licenses
Issue 1.0 UNIVERGE SV8100/SV8300 Table 3-8 Maximum System Capacity – Cables (Continued) 1 Unit System Max. Units Units Units Equipment Standalone Remote Unit RS RVS-4S CA-F RS RVS-4S CA-G RS PRT-15S CA-F BUS CABLE AC CORD 2U = Expansion Chassis N/A = Not Available Depends on the system configuration.
Page 149 UNIVERGE SV8100/SV8300 Issue 1.0 Table 3-9 System Licenses (Continued) Category License Description Feature LS-FEA-SMDR-LIC SMDR LS-FEA-OAI-LIC LS-FEA-SIP-T-LIC SIP Trunk LS-FEA-ISDN-LIC ISDN UM8000 LKS-UMS-CLIENT1-LIC UMS800 Mail View App Sessions 1 clients LKS-UMS-CLIENT4-LIC UMS800 Mail View App Sessions 4 clients LKS-UMS-CLIENT8-LIC UMS800 Mail View App Sessions 8...
Page 150 Issue 1.0 UNIVERGE SV8100/SV8300 Table 3-9 System Licenses (Continued) Category License Description Communications Analyst LKS-CA-20 STATION PKG-LIC SMB8000 Communications Analyst- 20 STA License Pack LKS-CA-256 STATION PKG-LIC SMB8000 Communications Analyst- 256 STA License Pack LKS-CA-NW-1CLIENT-LIC SMB8000 Communications Analyst- Network Client...
Page 151: Table 3-10 Blade Power Factor
UNIVERGE SV8100/SV8300 Issue 1.0 OWER ASED ALCULATOR HART ECTION The SV8300 system used two types of power factors. For a single chassis chart refer Table 3-10 Blade Power Factor. Refer to Table 3-11 Terminal Power Factor below, for the Terminal/Adapter power chart...
Page 152: Figure 3-5 Connecting The Dlc Using Twisted 2-Pair Cable
Issue 1.0 UNIVERGE SV8100/SV8300 YSTEM EQUIREMENTS PECIFICATIONS ECTION Cabling This section provides cabling requirements and specifications for various equipment used in the SV8300 system. Figure 3-5 Connecting the DLC Using Twisted 2-Pair Cable provides a diagram of the chassis connected with each of the multiline terminals and single line telephones by a separate twisted 1-pair cable or 2-pair cable (only for Multiline Terminals).
Page 153 UNIVERGE SV8100/SV8300 Issue 1.0 Table 3-12 Cable Length of Terminals (Continued) Cable Cable Length between Terminal Remarks SV8300 and Terminal Kind of Cable Pair Long Line Twisted Pair Cable 1-pair 13123 ft (4000m) with 22 AWG Loop Resistance: Telephone Maximum...
Page 154 Issue 1.0 UNIVERGE SV8100/SV8300 Table 3-13 Cable Length of Optional Equipment (Continued) Cable Cable Length between Terminal Remarks SV8300 and Terminal Kind of Cable Pair SMDR (LAN) LAN Cable (UTP 2-pair 328 ft (100m) or less – cable10BASE-T/ 100BASE-TX) Hotel Server...
Page 155: Table 3-14 Power Consumption
UNIVERGE SV8100/SV8300 Issue 1.0 VA @ 120V: Controlling Chassis=263 VA, Expansion Chassis= 263 VA, total 526 VA KWh @ AC Input I x 120V/1000: Controlling Chassis=0.263 KWh, Expansion Chassis=0.263 KWh, total 0.526 BTU (KWh x 3413): Controlling Chassis=1795 BTU, Expansion...
Page 156 Issue 1.0 UNIVERGE SV8100/SV8300 Humidity: 10 ~ 90% RH (non-condensing) Recommended Long Term Humidity: 10 ~ 90% RH Blades - CD-4LCA, PZ-4LCA, CD-8LCA, PZ-8LCE, CD-4COTB, PZ-4COTF, CD-PRTA, CD-CCTA Operating Temperature: +32°F ~ +104°F (0°C ~ 40°C) Recommended Long Term Temperature: -4°F ~ +140°F (20°C ~ 60°C)
Page 157 UNIVERGE SV8100/SV8300 Issue 1.0 Transmission, Network, and Control Specifications 6.5.1 Transmission Data Length: From Multiline Terminal to CD-8DLCA: 23 bits From CD-8DLCA to Multiline Terminal: 23 bits Data Transmission Rates: Between CD-8DLCA and Multiline Terminal: 184K bps (voice and signaling) Scanning Time for each Multiline Terminal: 32 ms.
Page 158 Issue 1.0 UNIVERGE SV8100/SV8300 6.5.4 Multiline Terminals and Equipment The voltage, current, and ring signal for the Multiline Terminals, Single Line Telephone equipment, and AP(A)-R/AP(R)-R Units are listed below: Multiline Terminal Voltage: -11 ~ -26 Vdc Maximum Current: 250 mA...
Page 159 UNIVERGE SV8100/SV8300 Issue 1.0 6.5.5 Series i Terminals term The voltage and current for the D Series i Multiline Terminals are listed below: Voltage: -11 ~ -48 Vdc Maximum Current: 250 mA Acoustical characteristics meet Electronic Industry Association (EIA) standard proposal SP-1286 and standard EIA RS-470.
Page 160 Issue 1.0 UNIVERGE SV8100/SV8300 Rise Time: Within 5 ms. Duration of Dual Frequency Signal: 110 ms. default/60 ms. minimum Interdigital Time: 140 ms. default/45 ms. minimum Nominal High Group Frequencies (Hz) 1209 1336 1477 Nominal Low Group Frequencies (Hz) 6.6.3...
Page 161 UNIVERGE SV8100/SV8300 Issue 1.0 6.6.7 External Tone Ringer/Night Chime Output Output Level: –10 dBm Output Impedance: 600 Ω Relay Contact Rating: 500 mA, 24 Vdc 6.6.8 SMDR Output Female Connector (LAN) Standard DB-9 (straight) 6.6.9 PC Connection Female Connector (LAN) Standard DB-9 (straight) 6.6.10...
Page 162: Figure 3-6 Sv8300 Dimensions
Issue 1.0 UNIVERGE SV8100/SV8300 Weights and Dimensions Table 3-15 SV8300 Weights shows the weight of main equipment for SV8300. Figure 3-6 SV8300 Dimensions shows the dimension of main equipment for SV8300. 6.8.1 Weights Table 3-15 SV8300 Weights Equipment Weight Remarks Chassis: 176.4 oz...
Page 163 UNIVERGE SV8100/SV8300 Issue 1.0 6.8.2 Dimensions Controlling Chassis Expansion Chassis Figure 3-6 SV8300 Dimensions System Hardware Manual 3 - 29...
Page 164: Figure 3-7 Sv8300 Dimensions, Continued
Issue 1.0 UNIVERGE SV8100/SV8300 UNIT (Controlling Chassis + Expansion Chassis x 3) BASE UNIT Figure 3-7 SV8300 Dimensions, Continued 3 - 30 SV8300 System Specifications...
Page 165: Table 3-16 Lamp Display
UNIVERGE SV8100/SV8300 Issue 1.0 Audible and Visual Indication 6.9.1 Lamp Display Table 3-16 Lamp Display on page 3-31 shows the state of the Multiline Terminal. Table 3-16 Lamp Display Display State Cycle (second) Turning off Slow blinking 0.25 Blinking 0.25 0.125...
Page 166 Issue 1.0 UNIVERGE SV8100/SV8300 Table 3-17 Tone Patterns System Tone Frequency (Hz) Intermit Cycle (Fixed) (Fixed) (Default) 0.5 sec 0.5 sec On Busy Tone 480/620 0.5 sec Off 0.5 sec 1 sec 1 sec On Call Waiting Tone 440/480 1 sec Off...
Page 167: Table 3-18 Multiline Terminal Led Flash Pattern
UNIVERGE SV8100/SV8300 Issue 1.0 Table 3-18 Multiline Terminal LED Flash Pattern Condition Color Flash Patterns I-Use Green Busy Incoming Call I-Hold Green Line Key Call Hold Hold Recall Green Transfer Recall Green Live Monitoring Mode Green Message Waiting on Line Key...
Page 168: Table 3-19 Traffic Capacity
Issue 1.0 UNIVERGE SV8100/SV8300 RAFFIC APACITY ECTION Table 3-19 Traffic Capacity provides information about the traffic capacity for the basic system package and expanded system package. Table 3-19 Traffic Capacity Traffic Capacity (CC-CP00) System Max. 12000BHCA System with IP Trunk...
Page 169 Installing the SV8100 Chassis ENERAL NFORMATION ECTION This chapter contains information to help the technician install the chassis for the SV8100 system. The technician should be familiar with this section before installing any equipment. Chapter MDF/IDF C REPARATION AND ONSTRUCTION ECTION Pre-installation planning is essential.
Page 170 Chassis are normally rack mounted to protect against accident or flooding. The chassis should not be located directly beneath pipes. Leaks or condensation could damage the UNIVERGE SV8100/ SV8300 system equipment. The area where the chassis is located must be free of corrosive...
Page 171 UNIVERGE SV8100/SV8300 Issue 1.0 The operation of the system is virtually noiseless and allows wide selection of installation sites. Take care to ensure the chassis or cabling do not present a hazard to office traffic. To minimize cabling costs, a centralized location must be chosen.
Page 172 Issue 1.0 UNIVERGE SV8100/SV8300 Constructing the Main Distribution Frame (MDF) The Main Distribution Frame (MDF) has two different standard quick-connect terminal blocks that are mounted on a 3/4-inch plywood backboard. Mounting these blocks on standoffs for ease of access is recommended. The recommended blocks are 66B50 for termination of the MDF Cable Assembly and 66M50 for termination of the station cables.
Page 173: Table 4-2 Power Failure Transfer Connections (Fax Co)
UNIVERGE SV8100/SV8300 Issue 1.0 Power Failure Transfer The Power Failure Transfer relays are located on the COIU Blades (CN3). When selecting a Single Line Telephone for power failure transfer, make sure it matches the CO line dialing type (10 pps, 20 pps, or DTMF) where it is connected.
Page 174 Issue 1.0 UNIVERGE SV8100/SV8300 NSTALLING THE HASSIS ECTION The CHS2U-US chassis has six universal blade slots for legacy line/trunk blade (Single Line Telephone Interface, Digital Multiline Terminal Interface, Central Office Trunk, ISDN PRI Interface, etc.), In-skin Application Blades (In-skin UMS, In-Skin Router, etc.).
Page 175 This allows secure anchoring of the screws which support the weight of the chassis. Due to chassis weight, NEC recommends only a single CHS2U-US chassis per wall mount. System Hardware Manual 4 - 7...
Page 176: Figure 4-3 Wall Mount Spacing Guide (19" Chassis)
Issue 1.0 UNIVERGE SV8100/SV8300 Upper Surface of Wall Mount Bracket Figure 4-3 Wall Mount Spacing Guide (19” Chassis) Mark and drill the six holes required for a wall installation. Align screw holes in wall mount brackets with drilled holes. 4 - 8...
Page 177: Figure 4-4 Install Wall Mount Brackets With Screws
UNIVERGE SV8100/SV8300 Issue 1.0 Using six screws, secure the two wall mount brackets to the wall. Refer to Figure 4-4 Install Wall Mount Brackets with Screws for screw location. Figure 4-4 Install Wall Mount Brackets with Screws Using four screws, secure the metal fittings on the Left and Right sides of the 19”...
Page 178: Figure 4-5 Install Wall Mount Brackets With Screws
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 4-5 Install Wall Mount Brackets with Screws 4 - 10 Installing the SV8100 Chassis...
Page 179: Figure
UNIVERGE SV8100/SV8300 Issue 1.0 Align the metal fitting with the upper wall mount bracket. The lower metal fitting will rest against the lower wall mount bracket. Secure the metal fitting and upper wall mount bracket with a single screw (see...
Page 180: Figure 4-7 Secure Metal Fitting To Lower Wall Mount Bracket With Screws
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 4-7 Secure Metal Fitting to Lower Wall Mount Bracket with Screws Attach the supplied cable support bracket to either end of the lower wall mount bracket with a single screw (refer to Figure 4-8 Attach Cable Support Bracket with Screw on page 4-13).
Page 181: Figure 4-8 Attach Cable Support Bracket With Screw
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 4-8 Attach Cable Support Bracket with Screw The cable support bracket can be installed any of the four corners of the 19” chassis (refer to Figure 4-9 Attach Cable Support Bracket with Screw on page 4-14).
Page 182: Figure 4-9 Attach Cable Support Bracket With Screw
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 4-9 Attach Cable Support Bracket with Screw Connect the ground wire to all chassis. Refer to 3.5.5 Install 19” Chassis Grounding on page 4-39 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 4-27...
Page 183: Figure 4-10 Floor Mount Spacing Guide
UNIVERGE SV8100/SV8300 Issue 1.0 Floor Mounting the 19” Chassis The CHS2U-US controlling and expansion chassis can be mounted on the floor using the CHS BASE UNIT and the CHS2U JOINT BRACKET KIT. 3.2.1 CHS2U-US Chassis Installation Use the template shown in...
Page 184: Figure 4-11 Secure Chs Base Unit With Anchor Bolts
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 4-11 Secure CHS BASE UNIT with Anchor Bolts Install the five rubber feet to the bottom of the chassis. Figure 4-12 Install Rubber Feet Position the chassis on top of the CHS BASE UNIT. Secure the chassis to the CHS BASE UNIT using eight screws supplied with the CHS2U JOINT BRACKET KIT.
Page 185: Figure 4-13 Install Chs2U Joint Bracket Kit
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 4-13 Install CHS2U JOINT BRACKET KIT Connect the ground wire to all chassis. Refer to 3.5.5 Install 19” Chassis Grounding on page 4-39 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 4-27...
Page 186: Figure 4-14 Install Rubber Feet
Issue 1.0 UNIVERGE SV8100/SV8300 Install the five rubber feet to the bottom of each chassis. Figure 4-14 Install Rubber Feet Using supplied screws in the CHS2U JOINT BRACKET KIT, attach metal brackets to both ends of the 19” chassis and the CHS BASE UNIT.
Page 187: Figure 4-16 Assemble Stand Mount With Screws
UNIVERGE SV8100/SV8300 Issue 1.0 Connect the ground wire to all chassis. Refer to 3.5.5 Install 19” Chassis Grounding on page 4-39 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 4-27 to continue...
Page 188: Figure 4-17 Secure Chs2U-Us Chassis To Chs2U Stand Kit With Screws
Figure 4-18 Secure Stand Mount to Floor with Screws on page 4-21). To prevent possible damage to the 19” chassis due to falling, NEC recommends screws be installed in the stand mount brackets as soon as possible. 4 - 20...
Page 189: Figure 4-18 Secure Stand Mount To Floor With Screws
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 4-18 Secure Stand Mount to Floor with Screws Connect the ground wire to all chassis. Refer to 3.5.5 Install 19” Chassis Grounding on page 4-39 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 4-27...
Page 190: Figure 4-19 Attach Rubber Feet To Chs2U-Us Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 3.3.2 Multiple CHS2U-US Chassis Installation Expansion chassis (maximum of three) can be added to the CHS2U STAND KIT and will require an additional CHS2U STAND KIT (EXT) per chassis. Install the five rubber feet to the bottom of each chassis.
Page 191: Figure 4-21 Install Additional Chs2U Stand Kit (Ext)
UNIVERGE SV8100/SV8300 Issue 1.0 Expansion Plates Figure 4-20 Install Additional CHS2U STAND KIT (EXT) Metal brackets from the CHS2U JOINT BRACKET KITs will be required to secure the top end of the chassis with screws. See Figure 4-21 Install Additional CHS2U STAND KIT (EXT) on page 4-24.
Page 192: Figure 4-20 Install Additional Chs2U Stand Kit (Ext)
(EXT) on page 4-24). To prevent possible damage to the 19” chassis due to falling, NEC recommends screws be installed in the stand mount brackets as soon as possible. Connect the ground wire to all chassis. Refer to 3.5.5 Install 19”...
Page 193: Figure 4-22 Chs2U-Us Rack Mount Brackets
UNIVERGE SV8100/SV8300 Issue 1.0 Rack Mounting the 19” Chassis A single or multiple chassis can be rack mounted. Controlling and Expansion chassis can be racked mounted by stacking them horizontally. The 19” chassis requires two rack mount brackets per chassis for mounting.
Page 194: Figure 4-24 Rack Mount 19" Chs2U-Us
Issue 1.0 UNIVERGE SV8100/SV8300 Repeat for additional chassis mounting. Figure 4-23 Rack Mount Bracket Installed 19” CHS2U-US Carefully slide the chassis into desired location within the rack. Make sure the hooks on the mounting bracket are inserted into the back of the chassis, securing it in place.
Page 195 Inspect the equipment for any physical damage. If you are not sure about the function of a component, review the associated information within this manual. Contact your authorized NEC Sales Representative if you have additional questions. Note that the chassis does not initially contain any blades.
Page 196 Issue 1.0 UNIVERGE SV8100/SV8300 3.5.3 Installing the 19” Controlling Chassis Ensure the chassis is powered down. Do not remove or install this blade with the power on. Align the CD-CP00-US blade with the Slot 1 guides of the Controlling Chassis.
Page 197: Figure 4-27 Cd-Cp00-Us Blade Installed
The EXIFU cable connects the Controlling Chassis and its EXIFU-B1 interface to the second, third, and fourth EXIFU-E1 interface. Use only the CAT 5 cables provided by NEC to make the connections between the Controlling and Expansion Chassis. The PZ-BS10 provides:...
Page 198: Figure 4-28 Pz-Bs10 Expansion Bay In Controlling Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 3.5.4.1 Connector Pin-Out on the PZ-BS10/PZ-BS11 Table 4-3 PZ-BS10/PZ-BS11 Connector Pin-Out RJ-61 Cable Connector PZ-BS10 – CN2, CN3, CN 4 PZ-BS11 – CN3 Pin No. Connection HW_UP (+) HW_UP (-) HW_DWN (+) FS (+) FS (-)
Page 199: Figure 4-29 Open Base Chassis Cover
UNIVERGE SV8100/SV8300 Issue 1.0 From the left side of the chassis, pull cover outward to expose the expansion bay. Figure 4-29 Open Base Chassis Cover Pull the cover toward you to remove. Cover must be removed prior to installation of PZ-BS10 blade.
Page 200: Figure 4-32 Installing Pz-Bs10 Blade In Expansion Bay
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 4-31 PZ-BS10 Components Slide the PZ-BS10 blade into the chassis until resistance (back plane) is felt. Figure 4-32 Installing PZ-BS10 Blade in Expansion Bay Gently push until the blade seats and install the supplied retaining screw.
Page 201: Figure 4-33 Pz-Bs10 Blade Installed
UNIVERGE SV8100/SV8300 Issue 1.0 Align the door tabs with hinges and reattach the cover. Figure 4-33 PZ-BS10 Blade Installed Close the PZ-BS10 cover. Figure 4-34 PZ-BS10 Installed (Cover Closed) 3.5.4.3 Install the PZ-BS11 Expansion Blade in the CHS2U-US Expansion Chassis For the Expansion Chassis to function, the PZ-BS10 blade must be installed in Controlling Chassis.
Page 202: Figure 4-35 Pz-Bs11 Expansion Bay In Expansion Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 Locate the door positioned on the left end (expansion bay) of the Expansion Chassis. Expansion Bay Figure 4-35 PZ-BS11 Expansion Bay in Expansion Chassis From the left side of the chassis, pull cover outward to expose the expansion bay.
Page 203: Figure 4-37 Pz-Bs11 Blade Guides
UNIVERGE SV8100/SV8300 Issue 1.0 Pull the cover toward you to remove. Cover must be removed to install PZ-BS11 blade. Align the PZ-BS11 blade with the guides located within the expansion bay. Figure 4-37 PZ-BS11 Blade Guides Slide the PZ-BS11 blade into the chassis until resistance (back plane) is felt.
Page 204: Figure 4-39 Pz-Bs11 Blade Installed
Issue 1.0 UNIVERGE SV8100/SV8300 Align the door tabs with hinges and reattach the cover. Figure 4-39 PZ-BS11 Blade Installed Close the PZ-BS11 blade cover. Figure 4-40 PZ-BS11 Installed (Cover Closed) 4 - 36 Installing the SV8100 Chassis...
Page 205: Figure 4-41 19" Expansion Chassis Interface Units
PZ-BS10 Figure 4-41 19” Expansion Chassis Interface Units Ensure Controlling and Expansion chassis are powered down. Using the NEC provided CAT5 straight-through cable(s), attach one end to each Expansion Chassis CN2 connector on the PZ-BS11 blade (see Figure 4-42 System Expansion Cabling on page 4-38.
Page 206: Figure 4-42 System Expansion Cabling
Issue 1.0 UNIVERGE SV8100/SV8300 Install in Expansion Chassis Install in Expansion Chassis Install in Expansion Chassis Install in Controlling Chassis Figure 4-42 System Expansion Cabling Repeat for additional Expansion Chassis. 4 - 38 Installing the SV8100 Chassis...
Page 207: Install 19" Chassis Grounding
UNIVERGE SV8100/SV8300 Issue 1.0 3.5.5 Install 19” Chassis Grounding From the factory, the SG, ETH and PBXG grounds are located inside the chassis and are connected to the FG ground (frame ground) on the back of the chassis. Each chassis (CHS2U-US) in the system must be grounded separately using the procedure listed below.
Page 208: Figure 4-44 19" Chassis Grounding Lug (Multiple-Chassis)
Issue 1.0 UNIVERGE SV8100/SV8300 FG Lugs Electrical Service Ground Figure 4-44 19” Chassis Grounding Lug (Multiple-Chassis) 3.5.7 Install AC Power Cords Locate the supplied AC power cord and attach to the AC Inlet located on the back of the Controlling Chassis.
Page 209: Figure 4-46 Install 19" Ac Power Cords (Multiple-Chassis)
UNIVERGE SV8100/SV8300 Issue 1.0 3.5.8 Install AC Power Cords on Multiple-Chassis (Optional) Locate the supplied AC power cords and attach to the AC Inlets located on the back of the Controlling and Expansion Chassis. AC Power Cords to AC Inlets Figure 4-46 Install 19”...
Page 210: Figure 4-47 Removing Battery Access Panel
Issue 1.0 UNIVERGE SV8100/SV8300 ATTERY ONNECTION ECTION There are two types of battery connection to provide battery life in the event of a power failure, the internal battery and an external battery with CHS LARGE BATT BOX. Installing the Internal Batteries...
Page 211: Figure 4-48 Removing Access Panel
UNIVERGE SV8100/SV8300 Issue 1.0 Remove access panel containing the fan. Refer to Figure 4-48 Removing Access Panel Figure 4-49 Access Panel Removed. Figure 4-48 Removing Access Panel Figure 4-49 Access Panel Removed System Hardware Manual 4 - 43...
Page 212: Figure 4-50 Installing Cable Guide
Issue 1.0 UNIVERGE SV8100/SV8300 Using tie wraps, secure CHS2U BATT CABLE INT in cable guide bracket (refer to Figure 4-50 Installing Cable Guide). Figure 4-50 Installing Cable Guide With supplied screw, install cable guide in chassis (refer to Figure 4-51 Installing Cable Guide).
Page 213: Figure 4-52 Installing Two Batteries
UNIVERGE SV8100/SV8300 Issue 1.0 Install two 2.3 AH-12V batteries (locally procured) into the CHS2U BATT MTG KIT (refer to Figure 4-52 Installing Two Batteries). The first battery must be installed on the left side, then slid to the right due to an installation tab on the mounting kit.
Page 214: Figure 4-53 Installing Battery Cable
Issue 1.0 UNIVERGE SV8100/SV8300 Connect the provided battery cables to the batteries (refer to Figure 4-53 Installing Battery Cable). Figure 4-53 Installing Battery Cable Connect CHS2U BATT CABLE INT to battery connector (refer to Figure 4-54 Connecting CHS2U BATT CABLE INT).
Page 215: Figure 4-55 Installing Battery Tray Into Chs2U-Us Chassis
UNIVERGE SV8100/SV8300 Issue 1.0 Install CHS2U BATT MTG KIT into CHS2U-US chassis and tighten the retaining screws (see Figure 4-55 Installing Battery Tray into CHS2U-US Chassis). Figure 4-55 Installing Battery Tray into CHS2U-US Chassis Reinstall access panel containing the fan and secure with supplied screw...
Page 216: Table 4-4 Chs Large Batt Box Capacity
Issue 1.0 UNIVERGE SV8100/SV8300 Installing the External Batteries An optional (locally procured), external battery source can be used to provide power in the event of a power failure. CHS LARGE BATT BOX (Backup time = Three Hours for 30 Terminals)
Page 217: Figure 4-57 Floor Mount Spacing Guide
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 4-57 Floor Mount Spacing Guide Mark and drill the four holes required for installing the CHS BASE UNIT. Align bolt holes in CHS BASE UNIT (see Figure 4-57 Floor Mount Spacing Guide on page 4-49) with holes drilled in floor and secure using four anchor bolts.
Page 218: Figure 4-58 Installing The Chs Large Batt Box Using The Chs2U Joint Bracket Kit
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 4-58 Installing the CHS LARGE BATT BOX using the CHS2U JOINT BRACKET KIT Secure the CHS LARGE BATT BOX to the CHS BASE UNIT using the CHS2U JOINT BRACKET KIT. Refer to Figure 4-58 Installing the CHS LARGE BATT BOX using the CHS2U JOINT BRACKET KIT on page 4-50.
Page 219: Figure 4-60 Removing Battery Tray Suppressor
UNIVERGE SV8100/SV8300 Issue 1.0 Remove two screws from front of Battery Tray Suppressor. Refer to Figure 4-60 Removing Battery Tray Suppressor. Figure 4-60 Removing Battery Tray Suppressor Slide Battery Tray Suppressor outward to remove. Slide Battery Tray(s) out of CHS LARGE BATT BOX.
Page 220: Figure 4-62 Removing Battery Tray Bracket
Issue 1.0 UNIVERGE SV8100/SV8300 Remove two screws and remove the Battery Tray Bracket. Refer to Figure 4-62 Removing Battery Tray Bracket. Figure 4-62 Removing Battery Tray Bracket Refer to Figure 4-63 Connecting Battery Cables for connection of battery cable to battery terminals. Repeat for additional battery connection.
Page 221: Figure 4-64 Connecting Battery Cables
UNIVERGE SV8100/SV8300 Issue 1.0 Install batteries into Battery Tray. Refer to Figure 4-64 Connecting Battery Cables. Using two screws, install the Battery Tray Bracket. Refer to Figure 4-62 Removing Battery Tray Bracket on page 4-52. Figure 4-64 Connecting Battery Cables Insert Battery Connection Cable into cable guides.
Page 222: Figure 4-66 Installing Cover Battery
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 4-65 Connecting Battery Cables Insert tabs on cover into holes on CHS LARGE BATT BOX. Slide the cover left until seated and tighten the screw. Refer to Figure 4-66 Installing Cover Battery. Figure 4-66 Installing Cover Battery 4.2.3...
Page 223: Figure 4-67 Removing Fan Access Panel
UNIVERGE SV8100/SV8300 Issue 1.0 Remove fan access panel from rear of CHS2U-US chassis. Refer to Figure 4-67 Removing Fan Access Panel. Figure 4-67 Removing Fan Access Panel Connect one end of Battery Connection Cable to Battery Connector on rear of Basic and Expansion chassis.
Page 224: Figure 4-69 Single Chs Large Batt Box Connection
Issue 1.0 UNIVERGE SV8100/SV8300 Basic Expansion Figure 4-69 Single CHS LARGE BATT BOX Connection Basic Expansion Figure 4-70 Dual CHS LARGE BATT BOX Connection 4 - 56 Installing the SV8100 Chassis...
Page 225: Figure 4-71 Install The Fan Access Panel
UNIVERGE SV8100/SV8300 Issue 1.0 Insert the access panel tab into the rear of the CHS1U-US chassis running the Battery Connection Cable through the cutout. Secure panel with the retaining screw. Refer to Figure 4-71 Install the Fan Access Panel. Figure 4-71 Install the Fan Access Panel Connect grounding and AC power cables.
Page 226: Figure 4-72 19" Chassis Access Panel
CHS2U-US Chassis 5.1.1 Remove MPS7101 To reduce the possibility of electrical shock or damage to equipment, NEC recommends powering Off the chassis and disconnecting the AC cable from the power source before removing the chassis cover. Ensure the chassis is powered down.
Page 227: Figure 4-73 Opening Chassis Access Panel (19" Chassis)
UNIVERGE SV8100/SV8300 Issue 1.0 Swing access panel outward and unplug fan power cable. See Figure 4-73 Opening Chassis Access Panel (19” Chassis). Fan Power Cable Plug Figure 4-73 Opening Chassis Access Panel (19” Chassis) Remove the access panel and set aside.
Page 228: Figure 4-75 Unplugging Wiring Harness
Issue 1.0 UNIVERGE SV8100/SV8300 Carefully unplug both plugs securing the wiring harness to the back plane (refer to Figure 4-75 Unplugging Wiring Harness). Figure 4-75 Unplugging Wiring Harness Unplug the MPS7101 power switch cable. Refer to Figure 4-75 Unplugging Wiring Harness.
Page 229: Figure 4-77 Removing The Mps7101 Screws
UNIVERGE SV8100/SV8300 Issue 1.0 Loosen and remove the screws securing the MPS7101 to the chassis (refer to Figure 4-77 Removing the MPS7101 Screws). Figure 4-77 Removing the MPS7101 Screws Carefully lift the MPS7101 from the chassis and set aside. 5.1.2...
Page 230: Figure 4-78 Wiring Harness
Issue 1.0 UNIVERGE SV8100/SV8300 Install Ground Screw (green) securing grounding wire to chassis (refer to Figure 4-75 Unplugging Wiring Harness on page 4-60). Install power switch cable (refer to Figure 4-75 Unplugging Wiring Harness on page 4-60). Carefully install both plugs securing the wiring harness to the...
Page 231 UNIVERGE SV8100/SV8300 Issue 1.0 Figure 4-78 Wiring Harness Install chassis covering and secure with four screws. Connect grounding and AC power cable. If used, connect EXIFU cabling to any expansion chassis. System Hardware Manual 4 - 63...
Page 232 CHS2U-US Chassis 6.1.1 Remove Cooling Fan To reduce the possibility of electrical shock or damage to equipment, NEC recommends powering Off the chassis and disconnecting the AC cable from the power source before removing the chassis cover. Ensure the chassis is powered down.
Page 233: Figure 4-81 Chassis Access Panel Removed
UNIVERGE SV8100/SV8300 Issue 1.0 Swing access panel outward and unplug fan power cable. See Figure 4-80 Opening Chassis Access Panel (19” Chassis). Fan Power Cable Plug Figure 4-80 Opening Chassis Access Panel (19” Chassis) Remove chassis access panel from rear of chassis.
Page 234: Figure 4-80 Opening Chassis Access Panel (19" Chassis)
Issue 1.0 UNIVERGE SV8100/SV8300 6.1.2 Install Cooling Fan Align replacement fan with holes and secure with two screws (refer to Figure 4-81 Chassis Access Panel Removed on page 4-65. Install cabling into retention clips (refer to Figure 4-81 Chassis Access Panel Removed on page 4-65 Insert access panel hinges into slots on rear of chassis.
Page 235 Installing the SV8300 Chassis ENERAL NFORMATION ECTION This chapter contains information to help the technician install the chassis for the SV8300 system. The technician should be familiar with this section before installing any equipment. Chapter MDF/IDF C REPARATION AND ONSTRUCTION ECTION Pre-installation planning is essential.
Page 236 Issue 1.0 UNIVERGE SV8100/SV8300 To avoid damage, the chassis should not be placed on unstable surfaces. Although it is recommended to install the blades with the system power off, all blades can be installed hot, except for the following: CC-CP00...
Page 237 UNIVERGE SV8100/SV8300 Issue 1.0 2.3.2 Selecting a Permanent MDF Location When selecting a permanent site for the MDF, the technician may encounter some of the following conditions: Limited space is available but must be used. The available space may pose one or more environmental hazards.
Page 238: Table 4-1 Power Failure Transfer Connections
Issue 1.0 UNIVERGE SV8100/SV8300 The system requires a 3-prong dedicated 110 VAC 60 Hz circuit (NEMA 5-15 receptacle) located within 7 feet of the AC receptacle. Telco should install the RJ21X to the right of the Controlling Chassis. Extension blocks should be installed to the left of the Controlling Chassis.
Page 239 UNIVERGE SV8100/SV8300 Issue 1.0 NSTALLING THE HASSIS ECTION There are two types of chassis, the 19” CHS1U-US chassis and the 19” CHS2U-US chassis. The CHS1U-US chassis mounts the CC-CP00 blade, PZ-BS10 for the CHS2U-US chassis expansion, PZ-PW146(1U) Power Supply and Cooling FAN.
Page 240 Issue 1.0 UNIVERGE SV8100/SV8300 Internal Battery Mount Fan Unit AC Connector (inside of cover) Battery Connector Frame Ground (inside of cover) (FG) Terminal Figure 5-2 CHS1U-US Chassis (Rear View) Universal Slot for Legacy Line/Trunk blades and Application blades (six slots).
Page 241 UNIVERGE SV8100/SV8300 Issue 1.0 AC Connector Internal Battery Mount Fan Unit (inside of cover) Frame Ground Battery Connector (FG) Terminal (inside of cover) Figure 5-4 CHS2U-US Chassis (Rear View) Wall Mounting the 19” Chassis When wall mounting the chassis, ensure the wall can support the weight of the chassis (31 lbs per system chassis including blades, cords, power supply, etc.).
Page 242: Figure 5-5 Wall Mount Spacing Guide (19" Chassis)
Issue 1.0 UNIVERGE SV8100/SV8300 Recommended Screw Wall Type (Anchor Bolt Type) Concrete 4 mm (0.16 inch) by 25 mm (0.98 inch) Wood Maximum 3.5 mm (0.14 inch) DIA or Maximum 4.5 mm (0.17 inch) DIA Upper Surface of Wall Mount Bracket Figure 5-5 Wall Mount Spacing Guide (19”...
Page 243: Figure 5-6 Drilling Instructions For Anchor Bolt
UNIVERGE SV8100/SV8300 Issue 1.0 Mark and drill the six holes required for a wall installation. Drilling: Make a preliminary hole in the concrete, using a drill bit for small-diameter holes. Drill a hole in the concrete with a drill suitable for a plug bolt a little deeper than the plug bolt length.
Page 244: Figure 5-7 Install Wall Mount Brackets With Screws
Issue 1.0 UNIVERGE SV8100/SV8300 Using six screws, secure the two wall mount brackets to the wall. Refer to Figure 5-7 Install Wall Mount Brackets with Screws for screw location. Figure 5-7 Install Wall Mount Brackets with Screws 5 - 10...
Page 245: Figure 5-8 Install Wall Mount Brackets With Screws
UNIVERGE SV8100/SV8300 Issue 1.0 Using four screws, secure the metal fittings on the Left and Right sides of the 19” chassis. Refer to Figure 5-8 Install Wall Mount Brackets with Screws for screw location. Figure 5-8 Install Wall Mount Brackets with Screws...
Page 246: Figure 5-9 Install Joint Brackets With Screws
Issue 1.0 UNIVERGE SV8100/SV8300 Install five rubber feet on bottom of CHS1U-US chassis. Align CHS1U-US and CHS2U-US chassis. Secure the two chassis together with a joint bracket and four screws on both sides of the chassis. Refer to Figure 5-9 Install Joint Brackets with Screws for bracket location.
Page 247: Figure 5-10 Secure Metal Fitting To Upper Wall Mount Bracket With A Screw
UNIVERGE SV8100/SV8300 Issue 1.0 Align the metal fitting with the upper wall mount bracket. The lower metal fitting will rest against the lower wall mount bracket. Secure the metal fitting and upper wall mount bracket with a single screw (see...
Page 248: Figure 5-11 Attach Cable Support Bracket With Screw
Issue 1.0 UNIVERGE SV8100/SV8300 The cable support bracket can be installed any of the four corners of the 19” chassis (refer to Figure 5-11 Attach Cable Support Bracket with Screw). Figure 5-11 Attach Cable Support Bracket with Screw 5 - 14...
Page 249: Figure 5-12 Attach Cable Support Bracket With Screw
UNIVERGE SV8100/SV8300 Issue 1.0 Attach the supplied cable support bracket to either end of the lower wall mount bracket with a single screw (refer to Figure 5-12 Attach Cable Support Bracket with Screw). Figure 5-12 Attach Cable Support Bracket with Screw...
Page 250: Figure 5-13 Chs1U-Us And Chs2U-Us Chassis Wall Mounted
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 5-13 CHS1U-US and CHS2U-US Chassis Wall Mounted Connect the ground wire to all chassis. Refer to 3.5.7 Install 19” Chassis Grounding on page 5-46 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 5-34...
Page 251: Figure 5-14 Chs Base Unit
UNIVERGE SV8100/SV8300 Issue 1.0 Floor Mounting the 19” Chassis The CHS1U-US controlling and the CHS2U-US expansion chassis can be mounted on the floor using the CHS BASE UNIT and the CHS2U JOINT BRACKET KIT. 3.2.1 CHS1U-US Chassis Installation Position the CHS BASE UNIT on desired surface and mark...
Page 252: Figure 5-16 Install Rubber Feet
Issue 1.0 UNIVERGE SV8100/SV8300 Install the five rubber feet to the bottom of the chassis. Figure 5-16 Install Rubber Feet Position the CHS1U-US and CHS2U-US chassis on top of the CHS BASE UNIT. Secure the chassis to the CHS BASE UNIT using screws supplied with the CHS STAND KIT (K).
Page 253: Figure 5-18 Install Rubber Feet
UNIVERGE SV8100/SV8300 Issue 1.0 Refer to 3.5 Installing the 19” Chassis on page 5-34 to continue installation of the chassis or, Chapter 5 paragraph Installing an Extension or Trunk Blade on page 6-4 installation of blades. 3.2.2 Multiple CHS2U-US Chassis Installation Expansion chassis can be secured to the CHS BASE UNIT and will require an additional CHS2U JOINT BRACKET KIT per chassis.
Page 254: Figure 5-20 Stand Mount Spacing Guide (Chs1U-Us+Chs2U-Usx1 Chassis Installation)
Issue 1.0 UNIVERGE SV8100/SV8300 Connect the ground wire to all chassis. Refer to 3.5.7 Install 19” Chassis Grounding on page 5-46 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 5-34 to continue...
Page 255: Figure 5-21 Attach Rubber Feet To Chs2U-Us Chassis
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 5-20 Stand Mount Spacing Guide (CHS1U-US+CHS2U-USx1 Chassis Installation) Drill the two holes required for a floor installation. Install the five rubber feet to the bottom of each chassis. Figure 5-21 Attach Rubber Feet to CHS2U-US Chassis...
Page 256: Figure 5-22 Install Joint Brackets With Screws
Issue 1.0 UNIVERGE SV8100/SV8300 Align CHS1U-US chassis and CHS2U-US chassis. Secure the two chassis together with a joint bracket and four screws on top sides of the chassis. Refer to Figure 5-22 Install Joint Brackets with Screws for bracket location.
Page 257: Figure 5-24 Attach Floor Mount Brackets To Chassis With Screws
UNIVERGE SV8100/SV8300 Issue 1.0 Using supplied screws, secure the chassis to the assembled CHS STAND KIT (K). Refer to Figure 5-24 Attach Floor Mount Brackets to Chassis with Screws for screw location. Figure 5-24 Attach Floor Mount Brackets to Chassis with Screws Align screw holes in floor mount bracket with pre-drilled holes in floor.
Page 258: Figure 5-25 Chs2U-Us/Chs1U-Us Chassis Stand Mount
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 5-25 CHS2U-US/CHS1U-US Chassis Stand Mount Connect the ground wire to all chassis. Refer to 3.5.7 Install 19” Chassis Grounding on page 5-46 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 5-34 to continue installation of the chassis or, Chapter 5 paragraph 2.2 Installing...
Page 259 UNIVERGE SV8100/SV8300 Issue 1.0 It is suggested that plywood first be installed on the floor where the chassis will be positioned. This allows for secure anchoring of the screws which will be supporting the weight of the chassis. For Stand Mounting, up to three CHS2U-US chassis can stand with a CHS1U-US chassis.
Page 260: Figure 5-27 Attach Rubber Feet To Chs2U-Us Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 Install the five rubber feet to the bottom of each chassis. Figure 5-27 Attach Rubber Feet to CHS2U-US Chassis Align CHS1U-US chassis and CHS2U-US chassis. Secure the chassis together with a joint bracket on top sides of the chassis.
Page 261: Figure 5-28 Assemble Stand Mount With Screws (Chs1U-Us+Chs2U-Usx2 Configuration)
UNIVERGE SV8100/SV8300 Issue 1.0 Expansion Screws Plate Figure 5-28 Assemble Stand Mount with Screws (CHS1U-US+CHS2U-USx2 Configuration) 3.3.2.2 CHS1U-US+CHS2U-USx3 Stand Mount Assembly Using supplied screws, assemble the CHS STAND KIT (K) and CHS2U STAND KIT (EXT). Refer to Figure 5-29 Assemble Stand Mount with Screws (CHS1U-US+CHS2U-USx3 Configuration) screw location.
Page 262: Figure 5-30 Attach Stand Mount Brackets To Chassis With Screws (Chs1U-Us+Chs2U-Usx2 Configuration)
Issue 1.0 UNIVERGE SV8100/SV8300 Using supplied screws, secure the chassis to the assembled CHS STAND KIT (K). Refer to Figure 5-30 Attach Stand Mount Brackets to Chassis with Screws (CHS1U-US+CHS2U-USx2 Configuration) for screw location. 3.3.2.3 CHS1U-US+CHS2U-USx2 Install Chassis Using supplied screws, secure the chassis to the assembled CHS STAND KIT (K).
Page 263: Figure 5-31 Attach Stand Mount Brackets To Chassis With Screws (Chs1U-Us+Chs2U-Usx3 Configuration)
UNIVERGE SV8100/SV8300 Issue 1.0 3.3.2.4 CHS1U-US+CHS2U-USx3 Install Chassis Using supplied screws, secure the chassis to the assembled CHS STAND KIT (K). Refer to Figure 5-31 Attach Stand Mount Brackets to Chassis with Screws (CHS1U-US+CHS2U-USx3 Configuration) for screw location. Figure 5-31...
Page 264: Figure 5-32 Chs1U-Us+Chs2U-Usx2 Chassis Configuration
Figure 5-33 CHS1U-US+CHS2U-USx3 Chassis Configuration on page 5-31. To prevent damage to the 1U/2U chassis due to falling, NEC recommends screws be installed in the floor mount brackets as soon as possible. Figure 5-32 CHS1U-US+CHS2U-USx2 Chassis Configuration 5 - 30...
Page 265: Figure 5-33 Chs1U-Us+Chs2U-Usx3 Chassis Configuration
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 5-33 CHS1U-US+CHS2U-USx3 Chassis Configuration Connect the ground wire to all chassis. Refer to 3.5.7 Install 19” Chassis Grounding on page 5-46 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 5-34 to continue installation of the chassis or, Chapter 5 paragraph 2.3 Installing...
Page 266: Figure 5-34 19" Rack Mount Brackets
Issue 1.0 UNIVERGE SV8100/SV8300 Rack Mounting the 19” Chassis A single or multiple chassis can be rack mounted. Controlling and Expansion chassis can be racked mounted by stacking them vertically. The 19” chassis requires two rack mount brackets per chassis for mounting.
Page 267: Figure 5-36 Rack Mount Bracket Installed 19" Chs2U-Us Chassis
UNIVERGE SV8100/SV8300 Issue 1.0 Repeat for additional chassis mounting. Figure 5-35 Rack Mount Bracket Installed 19” CHS1U-US Chassis Figure 5-36 Rack Mount Bracket Installed 19” CHS2U-US Chassis Carefully slide the chassis into desired location within the rack. Make sure the hooks on the mounting bracket are inserted into the back of the chassis, securing it in place.
Page 268: Figure 5-37 Rack Mount 19" Chs1U-Us And Chs2U-Us Chassis
Inspect the equipment for any physical damage. If you are not sure about the function of a component, review the associated information within this manual. Contact your authorized NEC Sales Representative if you have additional questions. Note that the chassis does not initially contain any blades.
Page 269: Figure 5-38 19" Chs1U-Us Controlling Chassis
UNIVERGE SV8100/SV8300 Issue 1.0 Ensure that you have a building plan showing common equipment, extensions, the Telco demarcation and earth ground location before you start installation. Be sure to properly plan your installation site and that you are familiar with the installation safety precautions. If you have not done that, please do so now.
Page 270: Figure 5-39 19" Chs2U-Us Expansion Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 Slide the CC-CP00 blade into the chassis until resistance (back plane) is felt. Gently push until the blade seats. Tighten the two retaining screws on front of the blade. 3.5.4 Installing the 19” Expansion Chassis Do not remove or install this blade with the power on.
Page 271: Table 5-2 Pz-Bs10/Pz-Bs11 Connector Pin-Out
The BUS cable is used to connect the Controlling Chassis and its PZ-BS10 to the second, third, and fourth PZ-BS11 interface. Use only the CAT 5 cables provided by NEC to make the connections between the Controlling and Expansion Chassis.
Page 272: Figure 5-40 Pz-Bs10 Expansion Bay In Controlling Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 3.5.5.2 Install the PZ-BS10 Expansion Base Blade in the CHS1U-US Controlling Chassis 1. Ensure the chassis is powered down. Do not remove or install this blade with the power on. 2. Locate the door positioned on the left end (expansion...
Page 273: Figure 5-42 Pz-Bs10 Blade Guides
UNIVERGE SV8100/SV8300 Issue 1.0 Cover must be removed prior to installation of PZ-BS10 blade. 5. Align the PZ-BS10 blade with the guides located within the expansion bay (refer to Figure 5-42 PZ-BS10 Blade Guides). Guides Figure 5-42 PZ-BS10 Blade Guides...
Page 274: Figure 5-44 Installing Pz-Bs10 Blade In Expansion Bay
Issue 1.0 UNIVERGE SV8100/SV8300 6. Slide the PZ-BS10 blade into the chassis until resistance (back plane) is felt. Figure 5-44 Installing PZ-BS10 Blade in Expansion Bay 7. Gently push until the blade seats and install the supplied retaining screw. 8. Align the door with the hinge and reattach the door.
Page 275 UNIVERGE SV8100/SV8300 Issue 1.0 3.5.5.3 Install the PZ-BS11 Expansion Blade in the CHS2U-US Expansion Chassis For the Expansion Chassis to function, the PZ-BS10 blade must be installed in Controlling Chassis. Do not remove or install this blade with the power on.
Page 276: Figure 5-48 Open Expansion Chassis Cover
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 5-48 Open Expansion Chassis Cover 4. Pull the cover toward you to remove. Cover must be removed to install PZ-BS11 blade. 5. Align the PZ-BS11 blade with the guides located within the expansion bay. Figure 5-49 PZ-BS11 Blade Guides...
Page 277: Figure 5-51 Pz-Bs11 Blade Installed
UNIVERGE SV8100/SV8300 Issue 1.0 6. Slide the PZ-BS11 blade into the chassis until resistance (back plane) is felt. Figure 5-50 Installing PZ-BS11 Blade in Expansion Chassis 7. Gently push until the blade seats and install the supplied retaining screw. 8. Align the door tabs with hinges and reattach the cover.
Page 278: Figure 5-52 Pz-Bs11 Installed (Cover Closed)
Issue 1.0 UNIVERGE SV8100/SV8300 Close the PZ-BS11 blade cover. Figure 5-52 PZ-BS11 Installed (Cover Closed) 3.5.5.4 Connect the Controlling and Expansion Chassis Installment of the PZ-BS10 blade and PZ-BS11 blade(s) must be completed prior to installation of the provided (Cat 5) expansion cabling...
Page 279: Figure 5-54 System Expansion Cabling
UNIVERGE SV8100/SV8300 Issue 1.0 1. Ensure Controlling and Expansion chassis are powered down. 2. Using the NEC provided CAT5 straight-through cable(s), attach one end to each Expansion Chassis BUS connector on the PZ-BS11 blade (see Figure 5-54 System Expansion Cabling. Attach the opposite end to the BUS connector on the PZ-BS10 of the Controlling Chassis.
Page 280: Figure 5-55 Cable Connection Between Cpu Blades
Issue 1.0 UNIVERGE SV8100/SV8300 3.5.6 Cable Connection between CPU Blades When providing multiple-unit configuration, the IP connection between UNITs is required. The UNIT is connected to IP network via the VoIPDB blade on the CPU blade. Refer to Figure 5-55 Cable Connection between CPU Blades.
Page 281: Figure 5-56 Chassis Grounding Lug
UNIVERGE SV8100/SV8300 Issue 1.0 Ground each chassis by connecting a 14 AWG wire from the FG lug on the back side of the chassis to an electrical service ground (such as a cold water pipe). CHS2U-US FG Lug CHS1U-US Figure 5-56 Chassis Grounding Lug 3.5.8...
Page 282: Install Ac Power Cords
Issue 1.0 UNIVERGE SV8100/SV8300 Ground each chassis by connecting a 14 AWG wire from the FG lug on the back side of the chassis to an electrical service ground (such as a cold water pipe). FG Lugs Electrical Service Ground Figure 5-57 19”...
Page 283: Install Ac Power Cords On Multiple-Chassis (Optional)
UNIVERGE SV8100/SV8300 Issue 1.0 3.5.10 Install AC Power Cords on Multiple-Chassis (Optional) Locate the supplied AC power cords and attach to the AC Inlets located on the back of the Controlling and Expansion Chassis. AC Power Cords to AC Inlets Figure 5-59 Install 19”...
Page 284: Battery Connection
Issue 1.0 UNIVERGE SV8100/SV8300 ATTERY ONNECTION ECTION There are three types of battery connection to provide battery life in the event of a power failure, internal battery, external battery without CHS LARGE BATT BOX and external battery with CHS LARGE BATT BOX.
Page 285: Figure 5-61 Removing Access Panel
UNIVERGE SV8100/SV8300 Issue 1.0 Remove access panel containing the fan (refer to Figure 5-61 Removing Access Panel). Figure 5-61 Removing Access Panel Using tie wraps, secure the CHS1U BATT CA INT to the Cable support bracket (refer to Figure 5-62 Securing Cable to Support Bracket).
Page 286: Figure 5-63 Securing Cable Support Bracket To Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 Using supplied screw, secure Cable Support Bracket to CHS1U-US (see Figure 5-63 Securing Cable Support Bracket Chassis). Figure 5-63 Securing Cable Support Bracket to Chassis Using supplied screws, secure two 12V-0.8AH (locally supplied) batteries to battery tray (see...
Page 287: Figure 5-65 Battery Connections To Chs1U Batt Ca Int
UNIVERGE SV8100/SV8300 Issue 1.0 Connect CHS1U BATT CA INT to internal batteries (12V-0.8AH battery). Refer to Figure 5-65 Battery Connections to CHS1U BATT CA INT. Figure 5-65 Battery Connections to CHS1U BATT CA INT Connect CHS1U BATT CA INT to battery connection on PSU...
Page 288: Figure 5-67 Install Battery Tray Into Chs1U-Us Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 Slide battery tray into space on rear of chassis (see Figure 5-67 Install Battery Tray into CHS1U-US Chassis). Figure 5-67 Install Battery Tray into CHS1U-US Chassis Secure battery tray using two retaining screws (refer to Figure 5-67 Install Battery Tray into CHS1U-US Chassis).
Page 289: Install Internal Batteries Chs2U-Us Chassis
UNIVERGE SV8100/SV8300 Issue 1.0 4.1.2 Install Internal Batteries CHS2U-US Chassis An internal battery source using two batteries can be installed using the CHS2U BATT MTG KIT (mounting kit) and CHS2U BATT CA INT (internal cabling). Remove screws from battery access panel on rear of chassis.
Page 290: Figure 5-71 Installing Cable Guide
Issue 1.0 UNIVERGE SV8100/SV8300 Using tie wraps, secure CHS2U BATT CA INT in cable guide bracket (refer to Figure 5-71 Installing Cable Guide). Figure 5-71 Installing Cable Guide With supplied screw, install cable guide in chassis (refer to Figure 5-72 Installing Cable Guide).
Page 291: Figure 5-73 Installing Two Batteries
UNIVERGE SV8100/SV8300 Issue 1.0 Install two batteries (12V-2.3AH) into the CHS2U BATT MTG KIT (refer to Figure 5-73 Installing Two Batteries). The first battery must be installed on the left side, then slid to the right due to an installation tab on the mounting kit.
Page 292: Figure 5-74 Installing Battery Cable
Issue 1.0 UNIVERGE SV8100/SV8300 Connect the provided battery cables to the batteries (refer to Figure 5-74 Installing Battery Cable). Figure 5-74 Installing Battery Cable Connect CHS2U BATT CA INT to battery connector (refer to Figure 5-75 Connecting CHS2U BATT CA INT).
Page 293: Figure 5-76 Installing Battery Tray Into Chs2U-Us Chassis
UNIVERGE SV8100/SV8300 Issue 1.0 Install CHS2U BATT MTG KIT into CHS2U-US chassis (see Figure 5-76 Installing Battery Tray into CHS2U-US Chassis). Figure 5-76 Installing Battery Tray into CHS2U-US Chassis Tighten the retaining screws (refer to Figure 5-76 Installing Battery Tray into CHS2U-US Chassis).
Page 294: Install External Batteries (Without Chs Large Batt Box)
Issue 1.0 UNIVERGE SV8100/SV8300 Install External Batteries (without CHS LARGE BATT BOX) An external battery source can be used to provide longer battery life in the event of a power failure. Remove fan access panel from rear of CHS1U-US chassis (refer to Figure 5-78 External Battery Box).
Page 295: Figure 5-80 External Battery Box (1U+2Ux1 Configuration) - Two Batteries
UNIVERGE SV8100/SV8300 Issue 1.0 Connect locally supplied external batteries and CHS2U BATT CA EXT-A (see Figure 5-80 External Battery Box (1U+2Ux1 Configuration) – Two Batteries) for two batteries and (see Figure 5-81 External Battery Box (1U+2Ux2/1U=2Ux3 Configuration) – Four Batteries) for four batteries.
Page 296: Figure 5-82 Connecting External Battery Box To Chs1U-Us And Chs2U-Us Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 Connect other end of cable to battery connector on rear of CHS1U-US and CHS2U-US chassis (refer to Figure 5-82 Connecting External Battery Box to CHS1U-US and CHS2U-US Chassis). Figure 5-82 Connecting External Battery Box to CHS1U-US...
Page 297: Install External Batteries (With Chs Large Batt Box)
UNIVERGE SV8100/SV8300 Issue 1.0 Insert the access panel tab into the slot on the rear of the CHS2U-US chassis (see Figure 5-84 Re-Install Fan Access Panel (CHS2U-US Chassis)). Figure 5-84 Re-Install Fan Access Panel (CHS2U-US Chassis) Secure panel withe retaining screw (refer to...
Page 298: When Providing 45 Minutes Backup Time
Issue 1.0 UNIVERGE SV8100/SV8300 4.3.1 When providing 45 minutes backup time: One CHS LARGE BATT BOX can support per one UNIT (1U+2Ux3). Figure 5-85 CHS LARGE BATT BOX (45 Minutes Battery Backup) Table 5-3 Battery Capacity of External Battery Battery Capacity...
Page 299: When Providing 3 Hours Backup Time
UNIVERGE SV8100/SV8300 Issue 1.0 4.3.2 When providing 3 hours backup time: One CHS LARGE BATT BOX can support one chassis (1U or 2U). Figure 5-86 CHS LARGE BATT BOX (3 Hours Battery Backup) Table 5-4 Battery Capacity of External Battery...
Page 300: Figure 5-87 Chs Base Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Position the CHS BASE UNIT on desired surface and mark four holes to be drilled (refer to Figure 5-87 CHS BASE UNIT). Figure 5-87 CHS BASE UNIT Drill the four holes required for floor installation. Using four screws, secure the CHS BASE UNIT to the floor...
Page 301: Figure 5-89 Install Joint Brackets With Screws
UNIVERGE SV8100/SV8300 Issue 1.0 Secure the CHS LARGE BATT BOX to the CHS BASE UNIT using eight screws supplied with the CHS2U JOINT BRACKET KIT (refer to Figure 5-89 Install Joint Brackets with Screws bracket location). Figure 5-89 Install Joint Brackets with Screws...
Page 302: Figure 5-91 Removing Battery Tray
Issue 1.0 UNIVERGE SV8100/SV8300 Remove the battery tray bracket, then pull out the battery tray from CHS LARGE BATT BOX (refer to Figure 5-91 Removing Battery Tray). Figure 5-91 Removing Battery Tray Remove the top cover and battery bracket from the battery tray...
Page 303: Figure 5-93 Mounting Batteries
UNIVERGE SV8100/SV8300 Issue 1.0 Mount the batteries in the battery tray, then fix the batteries by the battery bracket (refer to Figure 5-93 Mounting Batteries). Figure 5-93 Mounting Batteries Connect the provided battery cables to the batteries (7AH-12V battery). (Refer to Figure 5-94 Connecting Battery Cables).
Page 304: Figure 5-95 Install Top Cover Of Battery Tray
Issue 1.0 UNIVERGE SV8100/SV8300 Install the top cover of battery tray (refer to Figure 5-95 Install Top Cover of Battery Tray). Figure 5-95 Install Top Cover of Battery Tray Insert the battery tray into the CHS LARGE BATT BOX. Do the STEP 7 to STEP 12 for the remained battery tray.
Page 305: Figure 5-97 Install Chs Large Batt Box Front Cover
UNIVERGE SV8100/SV8300 Issue 1.0 Install the front cover (refer to Figure 5-97 Install CHS LARGE BATT BOX Front Cover). Figure 5-97 Install CHS LARGE BATT BOX Front Cover Connect the IP3-L BATT BOX CABLE between the terminal unit in the CHS LARGE BATT BOX and battery connector of...
Page 306: Figure 5-99 Cable Connection Between Chassis And Chs Large Batt Box
Issue 1.0 UNIVERGE SV8100/SV8300 When providing 3 hours backup time: CHS LARGE BATT BOX Hole Chassis Figure 5-99 Cable Connection between Chassis and CHS LARGE BATT BOX (3 Hours Battery Backup) 5 - 72 Installing the SV8300 Chassis...
Page 307: Remove And Install Cooling Fan
CHS1U-US Chassis 5.1.1 Remove Cooling Fan To reduce the possibility of electrical shock or damage to equipment, NEC recommends powering Off the chassis and disconnecting the AC cable from the power source before removing the chassis cover. Ensure the chassis is powered down.
Page 308: Figure 5-101 Opening Chassis Access Panel (Chs1U-Us Chassis)
Issue 1.0 UNIVERGE SV8100/SV8300 Swing access panel outward and unplug fan power cable. See Figure 5-101 Opening Chassis Access Panel (CHS1U-US Chassis). Fan Power Cable Plug Figure 5-101 Opening Chassis Access Panel (CHS1U-US Chassis) Remove chassis access panel from rear of chassis.
Page 309: Install Cooling Fan
CHS2U-US Chassis 5.2.1 Remove Cooling Fan To reduce the possibility of electrical shock or damage to equipment, NEC recommends powering Off the chassis and disconnecting the AC cable from the power source before removing the chassis cover. Ensure the chassis is powered down.
Page 310: Figure 5-105 Chassis Access Panel Removed
Issue 1.0 UNIVERGE SV8100/SV8300 Swing access panel outward and unplug fan power cable. See Figure 5-104 Opening Chassis Access Panel (CHS2U-US Chassis). Fan Power Cable Plug Figure 5-104 Opening Chassis Access Panel (CHS2U-US Chassis) Remove chassis access panel from rear of chassis.
Page 311: Install Cooling Fan
UNIVERGE SV8100/SV8300 Issue 1.0 5.2.2 Install Cooling Fan Align replacement fan with holes and secure with two screws (refer to Figure 5-105 Chassis Access Panel Removed on page 5-76. Install cabling into retention clips (refer to Figure 5-105 Chassis Access Panel Removed on page 5-76).
Page 312 Issue 1.0 UNIVERGE SV8100/SV8300 - - NOTES - - 5 - 78 Installing the SV8300 Chassis...
Page 313: Chapter 6 Installing The Sv8100/Sv8300 Blades
ENERAL NFORMATION ECTION This chapter contains information to help the technician install the blades for the UNIVERGE SV8100/SV8300 system. The technician should be familiar with this section before installing any equipment. Chapter Slot Locations Each CHS2U-US has six slots. In the Controlling Chassis, the CD-CP00-US (for Key Systems) must be installed in the first slot (slot 1).
Page 314: Figure 6-1 19" Chassis Cpu And Expansion Slot Locations
Issue 1.0 UNIVERGE SV8100/SV8300 Controlling Chassis CPU Slot Expansion Chassis PZ-BS11 Slot Figure 6-1 19” Chassis CPU and Expansion Slot Locations 6 - 2 Installing the SV8100/SV8300 Blades...
Page 315 UNIVERGE SV8100/SV8300 Issue 1.0 ECTION NSTALLATION Pre-installation planning is essential. Advanced planning minimizes installation time, cost, and disruption of the customer business activities. Installation and Safety Precautions Observe the following precautions when installing the blades to avoid static electricity damage to hardware or exposure to hazardous voltages.
Page 316: Figure 6-2 Inserting Blades In The 19" Chs2U-Us Chassis
Issue 1.0 UNIVERGE SV8100/SV8300 Installing an Extension or Trunk Blade 2.2.1 Installing the Blades To install an extension/trunk blade with the system running: Insert the blade within the guide rail and push the blade securely into position. Tighten the thumb screws on either side of the blade.
Page 317: Table 6-1 Extension Blade Installation Order Example
UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-1 Extension Blade Installation Order Example Order of Blade Slot Extension Blade Installation Number Numbers CD-16DLCA 101~116 CD-16DLCA 117~132 CD-8DLCA 133~148 PZ-8LCE CD-8DLCA 149~164 After the initial powering up of the system, subsequent powering up or resets do not change the slot identification.
Page 318: Table 6-3 Trunk Blade Installation Order Example
Issue 1.0 UNIVERGE SV8100/SV8300 The system automatically recognizes each blade installed in the system. If a blade has previously been installed in a slot and another type of blade is to be installed in that same slot, the blade must first be removed from the chassis and then the slot definition removed using Program 90-05 prior to installing the new blade.
Page 319 UNIVERGE SV8100/SV8300 Issue 1.0 2.2.3.2 Installing CD-PRTA (T1/PRI) Blades The CD-PRTA (T1/PRI) Interface blade uses the first block of 24 consecutive trunks. For example, if an CD-4COTB and PZ-4COTF blade is installed for trunks 1~8, the CD-PRTA (T1/PRI) blade automatically uses trunks 9~32. If CD-4COTB and PZ-4COTF blades are installed for trunks 1~8 and 17~24, the CD-PRTA (T1/PRI) blade uses trunks 25~48.
Page 320 Issue 1.0 UNIVERGE SV8100/SV8300 Blade Capacities The universal architecture of the UNIVERGE SV8100/SV8300 provides flexibility when installing blades. With the exception of the CD-CP00-US and CC-CP00 blades, any blade can be installed in any slot. Table 2-4 Maximum System Capacities – Blades on page 2-9...
Page 321 UNIVERGE SV8100/SV8300 Issue 1.0 2.6.2 Performing a Hot Start The section describes how to load system software from flash memory and customer data from RAM memory. IMPORTANT CONSIDERATIONS System software is loaded from flash memory and the customer data is loaded from RAM memory.
Page 322: Table 6-4 Default Port Settings
Issue 1.0 UNIVERGE SV8100/SV8300 2.6.3.2 Port Defaults With the default settings, the ports are assigned as follows: Table 6-4 Default Port Settings Port 1~99 : 101~199 Station Ports: Port 100~199 : 3101~3200 Port 200~512 : 3201~3513 Port 1~99 : 201~299...
Page 323 UNIVERGE SV8100/SV8300 Issue 1.0 2.6.3.4 Saving Your Configuration When programming is completed, to exit out of the program option and save changes to the CD-CP00-US: 1. Press EXIT to exit the program options, if needed. 2. Press Speaker. Saving System Data is displayed if changes were made to system programming.
Page 324 Issue 1.0 UNIVERGE SV8100/SV8300 After reloading the customer data to the system, exit programming mode (this could take a minute or more to save the database), then reset the system by powering down and back up. If the system is not reset, not all the uploaded programming changes are in effect.
Page 325 UNIVERGE SV8100/SV8300 Issue 1.0 To perform a system software and firmware upgrade: Turn the system power off. Once the system has powered down, insert the USB Memory containing the software upgrade into the USB port on the CD-CP00-US. Push in and hold the Load button.
Page 326: Figure 6-3 Cd-Cp00-Us Blade Layout
Issue 1.0 UNIVERGE SV8100/SV8300 OMMON ONTROL LADES ECTION The blades described in this section control the common functions of the chassis. CD-CP00-US (SV8100 Central Processing Unit) PZ-32IPLA PZ-64IPLA PZ-128IPLA Battery Fast Ethernet CN7 BGM/EXSP Control CN 10 USB CN5 Status LED1...
Page 327: Description
UNIVERGE SV8100/SV8300 Issue 1.0 PZ-32IPLA PZ-64IPLA Battery PZ-128IPLA CompactFlash PZ-VM21 PZ-ME50 Figure 6-4 CD-CP00-US Blade with Daughter Boards Installed 3.1.1 Description The CD-CP00-US blade is available only for the SV8100 system. The CD-CP00-US controls all the functions and operations of the SV8100 system using the system software loaded into the CD-CP00-US memory.
Page 328 Issue 1.0 UNIVERGE SV8100/SV8300 USB Interface Circuit Ethernet Interface Circuit PZ-BS10/PZ-BS11 Interface Circuit Main Processing 32-Bit CPU Circuit (MPC8260 @ 2 MHz) Time Switch, Optional Blade Control Circuit Backboard Interface Circuit The CD-CP00-US provides: 200 trunk ports maximum 512 extension ports maximum –...
Page 329 UNIVERGE SV8100/SV8300 Issue 1.0 MF Sender MFC Tone Sender MF Signal Sender (Sends caller information to CO for E911) Call Progress Time Detection C-Channel Control Conference: 64 Channels Caller ID Receiver; 32 Channels Caller ID Generator; 4 or 10 Channels for Analog Stations...
Page 330: Installation
Issue 1.0 UNIVERGE SV8100/SV8300 Voice Mail Server (voice mail requires a compact flash card) SIP Server RTP Forwarding VoCoder Conversion 3.1.2 Installation Each SV8100 system must have the CD-CP00-US installed in Slot 1 of the Controlling Chassis. IMPORTANT INSTALLATION NOTES The chassis power must be off when installing or removing the CD-CP00-US.
Page 331: Figure 6-5 Cd-Cp00-Us Battery Installation
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 6-5 CD-CP00-US Battery Installation Refer to Figure 6-4 CD-CP00-US Blade with Daughter Boards Installed on page 6-15 to Install the PZ-VM21, PZ-ME50 and/or PZ-32IPLA/PZ-64IPLA/PZ-128IPLA daughter board, if required. Ensure the power supply is OFF, then slide the CPU into the CCPU slot in the Controlling Chassis.
Page 332: Table 6-5 Cd-Cp00-Us Switch Settings
Issue 1.0 UNIVERGE SV8100/SV8300 Customer information is stored in the RAM memory and, in case of a power failure, will be restored. The lithium battery in the system saves the RAM memory when power is lost. 3.1.3 Switch Settings Refer to...
Page 333: Led Indications
UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-6 CD-CP00-US Switch 6 Settings (Continued) Configuration Note SW6-4 Reset Configuration ON = Normal OFF = ICE Mode 3.1.4 LED Indications The LEDs on the CPU indicate the following: RUN (LED 1) = The CPU is operating (green)
Page 334: Table 6-8 Cd-Cp00-Us Connections
Issue 1.0 UNIVERGE SV8100/SV8300 Table 6-7 CD-CP00-US LED Indications (Continued) LED Indication Status RUN (LED1) LED2 LED3 LED4 LED5 Blinking Blinking Blinking On Steady When Finish formatting (SRAM, USB Memory is Flash) Installing Blinking DRAM error Blinking On Steady When...
Page 335: Table 6-9 Cd-Lta Rj11 Cable Connector Pin-Outs
UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-8 CD-CP00-US Connections (Continued) Connector Connector Description CN6/SW2 Used for Debug Purposes Ethernet Cable Connection (for PCPro or WebPro, CTI, ACD MIS, IP Phone) CN8/CN9 Pin Jack for External Source Connection (External MOH, External Speaker, etc.)
Page 336 Issue 1.0 UNIVERGE SV8100/SV8300 Table 6-9 CD-LTA RJ11 Cable Connector Pin-Outs (Continued) Pin Jack – CN8/CN9 (Polarity) Pin No. Signal EXT1 EXT2 RJ-45 Cable Connector – CN10 (External Source Control) (No Polarity) Pin No. Connection EXCNT2 EXCNT1 EXCNT1 EXCNT2 6 - 24...
Page 337 UNIVERGE SV8100/SV8300 Issue 1.0 CC-CP00 (SV8300 Central Processing Unit) PZ-64IPLA PZ-VM21 PZ-128IPLA CompactFlash (Not Used) Battery Ethernet Sense Status LED 1 – 4 Relay USB (Not Used) EX IN EX OUT Memory Reset Figure 6-6 CC-CP00 Blade 3.2.1 Description The CC-CP00 blade is available only for the SV8300 system.
Page 338 Issue 1.0 UNIVERGE SV8100/SV8300 System Program and System Data Storing Memory Circuit USB Interface Circuit Ethernet Interface Circuit PZ-BS10/PZ-BS11 Interface Circuit Main Processing 32-Bit CPU Circuit (MPC8260 @ 266 MHz) Time Switch, Optional Blade Control Circuit Backboard Interface Circuit The CC-CP00 provides:...
Page 339 Two Serial Ports (null modem/cross-over cable required) One USB Port – USB 1.1/2.0 (requires USB driver – download from NEC web site) Not Used One Gbit Ethernet Port for VOIPDB One Fast Ethernet Port (10 Base-T/100 Base-TX)
Page 340 Issue 1.0 UNIVERGE SV8100/SV8300 RTP Forwarding VoCoder Conversion 3.2.2 Installation Each SV8300 system must have the CC-CP00 installed in the Controlling Chassis. IMPORTANT INSTALLATION NOTES The power to the chassis must be off when installing or removing the CC-CP00. After removing a previously installed CPU handle the blade, carefully, from the edges.
Page 341: Figure 6-6 Cc-Cp00 Blade
UNIVERGE SV8100/SV8300 Issue 1.0 3.2.3 Switch Settings Refer to Table 6-10 CC-CP00 Switch Settings for system restart/ system reset and with system power on. Figure 6-6 CC-CP00 Blade on page 6-25 shows the location of the switches on the CC-CP00 blade.
Page 342: Table 6-11 Cc-Cp00 Led Indications
Issue 1.0 UNIVERGE SV8100/SV8300 3.2.4 LED Indications Table 6-11 CC-CP00 LED Indications provides a list of each LED and its associated operation and status indications. Refer to Figure 6-6 CC-CP00 Blade on page 6-25 for the location of the LEDs on the CC-CP00.
Page 343 UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-11 CC-CP00 LED Indications (Continued) Color Status Green Status indications on system reset. Blinking Blinking while copying the system data from the flash memory to the SDRAM/Blinking while downloading the DSP firmware program. Status indications of VoIPDB.
Page 344: Table 6-12 Cc-Cp00 Connections
Issue 1.0 UNIVERGE SV8100/SV8300 3.2.5 Connectors Table 6-12 CC-CP00 Connections describes each connector on the CD-CP00-US Table 6-13 CC-CP00 Connector Pin-Outs on page 6-33 describes the pin-outs for connectors on the CCPU-A. Refer to Figure 6-6 CC-CP00 Blade on page 6-25 for the location of the connections on the CCPU-A1 blade.
Page 345: Table 6-13 Cc-Cp00 Connector Pin-Outs
UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-13 CC-CP00 Connector Pin-Outs Ethernet Cable Connector – ETHERNET (RJ-45) (10Base-T/100Base-TX) Pin No. Signal Pin Jack – MOH (No Polarity) Pin No. Signal EXT1 EXT2 RJ-45 Cable Connector – RELAY (External Source Control) (No Polarity) Pin No.
Page 346 Issue 1.0 UNIVERGE SV8100/SV8300 Table 6-13 CC-CP00 Connector Pin-Outs (Continued) USB Cable Connector – USB (Type A, Female) (USB 1.1/2.0 Standard) [Not Used] Pin No. Signal 1 2 3 4 RJ-45 Cable Connector – EX IN/EX OUT (Polarity) Pin No.
Page 347: Figure 6-7 Pz-Me50 Daughter Board
PZ-ME50 (Memory Expansion Daughter Board) Figure 6-7 PZ-ME50 Daughter Board 3.3.1 Description The PZ-ME50 blade is available for both UNIVERGE SV8100/ SV8300 systems. The Memory Expansion daughter board (PZ-ME50) provides additional memory for the system for use with license control, expanded system networking, and software updates.
Page 348: Table 6-15 Pz-Me50 Capacities
Issue 1.0 UNIVERGE SV8100/SV8300 Table 6-15 PZ-ME50 Capacities provides the memory capacities for the PZ-ME50 blades. Table 6-15 PZ-ME50 Capacities Memory Description Equipped Memory Capacity SDRAM 128 MB 256 MB / 16 bit x 4 pcs Flash 32 MB 256 MB / 16 bit x 1 pc...
Page 349 UNIVERGE SV8100/SV8300 Issue 1.0 3.3.2 Installation To install a PZ-ME50 on the CD-CP00-US or CC-CP00: Do not remove or install the CD-CP00-US or CC-CP00 with the power on. For installation on the CD-CP00-US blade refer to Figure 6-4 CD-CP00-US Blade with Daughter Boards Installed on page 6-15.
Page 350: Figure 6-8 Pz-Vm21 Daughter Board
PZ-VM21 (Voice Mail Daughter Board) Figure 6-8 PZ-VM21 Daughter Board 3.4.1 Description PZ-VM21 is common to both UNIVERGE SV8100/SV8300 systems. The SV8100 voice mail is a fully integrated, “in-skin” voice mail with Automated Attendant. In addition to the voice mail function, the daughter board provides Voice Response System (VRS) and an optional modem ability for remote maintenance functions.
Page 351: Table 6-17 Pz-Vm21 Maximum Upgrade Capacities
Depending on the compact flash card used, the voice mail can provide: Table 6-18 CompactFlash Voice Mail Specifications Part Numbers and UNIVERGE SV8100/SV8300 VM8000 InMail Capacities P/N 670831 UNIVERGE SV8100/SV8300 VM8000 InMail 512M Drive (1) 32-hour CompactFlash Card with software. P/N 670784 UNIVERGE SV8100/SV8300 VM8000 InMail 8-Port License P/N 670872...
Page 352 Issue 1.0 UNIVERGE SV8100/SV8300 3.4.2 Installation To install a PZ-VM21 on the CD-CP00-US or CC-CP00: Do not remove or install the CD-CP00-US or CC-CP00 with the power on. Included with the PZ-VM21 are four plastic spacers. Install the plastic spacers onto the PZ-VM21. Make sure to attach the spacers so that they extend out on the side of the daughter board which has the CN1 connector.
Page 353: Figure 6-9 Installing The Pz-Vm21
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 6-9 Installing the PZ-VM21 One InMail can be installed per system. Refer to the Univerge UNIVERGE SV8100/SV8300 System InMail System Guide for complete set-up information. System Hardware Manual 6 - 41...
Page 354: Figure 6-10 Pz-32Ipla Voipdb-32 Daughter Board
Issue 1.0 UNIVERGE SV8100/SV8300 3.4.3 Switch Settings This daughter board does not have any switch that needs to be set and does not require any hardware setting. PZ-32IPLA/PZ-64IPLA/PZ-128IPLA (Voice over IP Daughter Boards) Figure 6-10 PZ-32IPLA VoIPDB-32 Daughter Board Figure 6-11 PZ-64IPLA VoIPDB-64 Blade...
Page 355: Figure 6-12 Pz-128Ipla Voipdb-128 Blade
3.5.1 Description The PZ-32IPLA, PZ-64IPLA and PZ-128IPLA daughter boards are common to both UNIVERGE SV8100/SV8300 systems. The PZ-32IPLA/PZ-64IPLA/PZ-128IPLA daughter boards are used for converting the RTP (Real Time Transfer Protocol) packets via the IP network and PCM highway. The daughter board is installed on the CD-CP00-US/CC-CP00.
Page 356: Table 6-19 Voipdb Maximum Upgrade Capacities
4-28 for more details. Connect the VOIPDB to the CD-RTB or to an external switching hub using an ethernet cable. Refer to the Univerge SV8100 Programming Manual for detailed programming instructions. 3.5.3 Switch Settings These daughter boards do not have any switches that need to be set and do not require any hardware setting.
Page 357: Table 6-20 Voipdb Led Indications
UNIVERGE SV8100/SV8300 Issue 1.0 3.5.4 LED Indications LED indications for the PZ-32IPLA, PZ-64IPLA and PZ-128IPLA Daughter Boards are indicated in Table 6-20 VOIPDB LED Indications. Each LED is listed with its associated function and LED and Operational status. Refer to...
Page 358: Figure 6-13 Voip Connections
Issue 1.0 UNIVERGE SV8100/SV8300 3.5.5 Connectors Figure 6-13 VoIP Connections shows a typical connection layout. Figure 6-14 Connecting a VOIPDB to a Network/PC illustrates how to connect a VoIP Daughter Board to a Network or PC. Figure 6-13 VoIP Connections...
Page 359 UNIVERGE SV8100/SV8300 Issue 1.0 Figure 6-14 Connecting a VOIPDB to a Network/PC System Hardware Manual 6 - 47...
Page 360: Figure 6-15 Cd-8Dlca Blade
Issue 1.0 UNIVERGE SV8100/SV8300 TATION LADES ECTION CD-8DLCA/CD-16DLCA (Digital Station Interface) Figure 6-15 CD-8DLCA Blade 6 - 48 Installing the SV8100/SV8300 Blades...
Page 361: Figure 6-16 Cd-16Dlca Blade
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 6-16 CD-16DLCA Blade 4.1.1 Description The CD-8DLCA and the CD-16DLCA are available for both the SV8100 and SV8300 systems. Both are discussed in this section. Any differences between the two are noted. These blades provide:...
Page 362: Table 6-22 Cd-8Dlca/Cd-16Dlca Maximum Upgrade Capacities
Issue 1.0 UNIVERGE SV8100/SV8300 Table 6-22 CD-8DLCA/CD-16DLCA Maximum Upgrade Capacities provides the maximum capacities for the ESIU blades when they are upgraded. Table 6-22 CD-8DLCA/CD-16DLCA Maximum Upgrade Capacities 19” 19” Chassis 19” Chassis Networked ESIU Chassis without CPU Chassis with CPU...
Page 363: Table 6-24 Cd-8Dlca/Cd-16Dlca/ Rj-61 Cable Connector Pin-Outs
UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-23 CD-8DLCA/CD-16DLCA LED Indications (Continued) LED Indication Operation Status Remarks Live LED Busy LED (Green) (Red) A Channel is busy (use – Flash Normal another from CH1 ~ CHx). (100ms) Operation All channels are idle.
Page 364 Issue 1.0 UNIVERGE SV8100/SV8300 Table 6-24 CD-8DLCA/CD-16DLCA/ RJ-61 Cable Connector Pin-Outs RJ-61 Cable Connector CD-8DLCA – CN101 (ports 1~4), CN201 (ports 5~8) CD-16DLCA – CN101 (ports 1~4), CN201 (ports 5~8), CN301 (ports 9~12), CN401 (ports 13~16) Pin No. Connection T4 (Tip for port 4)
Page 365: Figure 6-17 Pz-8Dlcb Blade
PZ-8DLCB (Digital Station Daughter Board) Figure 6-17 PZ-8DLCB Blade 4.2.1 Description The PZ-8DLCB blade is common to both UNIVERGE SV8100/ SV8300 systems. The PZ-8DLCB daughter board provides eight digital extensions. This daughter board is installed on the CD-8DLCA and expands the port capacity for the combined blades to 16.
Page 366: Table 6-26Pz-8Dlcb Cn301 Connection
Issue 1.0 UNIVERGE SV8100/SV8300 4.2.2 Installation The PZ-8DLCB is installed on the CD-8DLCA. To install: Connect the PZ-8DLCB to the CN2 connector on the CD-8DLCA blade. Refer to Figure 6-15 CD-8DLCA Blade on page 6-48 for the location of the connectors on the blade.
Page 367: Table 6-27 Pz-8Dlcb Cn401 Connection
UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-27 PZ-8DLCB CN401 Connection RJ-61 Cable Connector CN401 (ports 13~16) Pin No. Connection (T4) Tip for port 16 (T3) Tip for port 15 (T2) Tip for port 14 (R1) Ring for port 13 (T1) Tip for port 13...
Page 368: Figure 6-18 Cd-4Lca Blade
Issue 1.0 UNIVERGE SV8100/SV8300 CD-4LCA/ CD-8LCA (4-Port/8-Port Single Line Interface) Figure 6-18 CD-4LCA Blade 6 - 56 Installing the SV8100/SV8300 Blades...
Page 369: Figure 6-19 Cd-8Lca Blade
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 6-19 CD-8LCA Blade 4.3.1 Description The CD-4LCA CD-8LCA blade is common to both UNIVERGE SV8100/SV8300 systems. The 4/8SLIU blade provides four (4SLIU) analog extension ports or eight (8SLIU) analog extension ports (used for on-premise analog telephones, fax machines, and analog modems).
Page 370: Table 6-28 Cd-4Lca/Cd-8Lca Maximum Upgrade Capacities
Issue 1.0 UNIVERGE SV8100/SV8300 The 4SLIU and 8SLIU are not rated for OPX use. A 4DIOPU blade should be used instead (it supports the analog DID and single line telephone interface functions, such as Off-Premise Extensions). One extension status LED...
Page 371: Table 6-29 Cd-4Lca/Cd-8Lca Led Indications
UNIVERGE SV8100/SV8300 Issue 1.0 If the PZ-4LCA/PZ-8LCE is used, install this prior to inserting the CD-8LCA into the chassis 4.3.3 LED Indications LED indications for the CD-4LCA CD-8LCA are listed in Table 6-29 CD-4LCA/CD-8LCA LED Indications. Each LED is listed with its associated function and LED and Operational status.
Page 372: Table 6-30 Cd-4Lca/Cd-8Lca Rj-61 Cable Connector Pin-Outs
Issue 1.0 UNIVERGE SV8100/SV8300 4.3.4 Connectors Table 6-30 CD-4LCA/CD-8LCA RJ-61 Cable Connector Pin-Outs show the pin-outs for the RJ-61 connector. Refer to Figure 6-18 CD-4LCA Blade on page 6-56 Figure 6-19 CD-8LCA Blade on page 6-57 for illustrations showing the location of the connectors and...
Page 373: Figure 6-20 Installing The Pz-4Lca Daughter Board
UNIVERGE SV8100/SV8300 Issue 1.0 PZ-4LCA/PZ-8LCE (4-Port/8-Port SLI Daughter Boards) Figure 6-20 Installing the PZ-4LCA Daughter Board System Hardware Manual 6 - 61...
Page 374: Figure 6-21 Installing The Pz-8Lce Daughter Board
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 6-21 Installing the PZ-8LCE Daughter Board 6 - 62 Installing the SV8100/SV8300 Blades...
Page 375: Table 6-31 Cd-4Lca/Cd-8Lca Maximum Upgrade Capacities
UNIVERGE SV8100/SV8300 Issue 1.0 4.4.1 Description The PZ-4LCA and PZ-8LCE daughter boards are mounted on the CD-4LCA/CD-8LCA. These boards provide: 4-Port Single Line and 8-Port Single Line analog extension ports (used for on-premise analog telephones, fax machines, and analog modems).
Page 376 Issue 1.0 UNIVERGE SV8100/SV8300 4.4.2 Installation When connecting a fax machine or analog modem, make sure to set Program 15-03-03 to 1 (special terminal) to avoid communication problems. The SLIU and SLIDB are categorized as TNV2. With this designation, off-premise wiring is not acceptable.
Page 377: Table 6-32 Pz-4Lca/Pz-8Lce/ Rj-61 Cable Connector Pin-Outs
UNIVERGE SV8100/SV8300 Issue 1.0 4.4.3 Connectors Table 6-32 PZ-4LCA/PZ-8LCE/ RJ-61 Cable Connector Pin-Outs show the pin-outs for the RJ-61 connector. Refer to Figure 6-20 Installing the PZ-4LCA Daughter Board on page 6-61 Figure 6-21 Installing the PZ-8LCE Daughter Board on page 6-62 illustrations showing the location of the connectors on the SLIDB blades.
Page 378: Figure 6-22 Cd-Lta Blade
Issue 1.0 UNIVERGE SV8100/SV8300 term CD-LTA (D /SLT Combination) Figure 6-22 CD-LTA Blade 4.5.1 Description The CD-LTA blade is available only for the SV8100 system. The Digital Station/SLT Combination blade provides eight Digital Station ports and two analog ports. This blade allows for either a PZ-4COTF analog trunk daughter board or PZ-2BRIA daughter board to be installed.
Page 379: Table 6-33 Cd-Lta Maximum Upgrade Capacities
UNIVERGE SV8100/SV8300 Issue 1.0 The blade provides: Eight Digital Station ports Two analog extension ports Two status LEDs Table 6-33 CD-LTA Maximum Upgrade Capacities provides the maximum capacities for the CD-LTA blades when they are upgraded. Table 6-33 CD-LTA Maximum Upgrade Capacities...
Page 380: Table 6-34 Cd-Lta Led Indications
Issue 1.0 UNIVERGE SV8100/SV8300 4.5.3 LED Indications LED indications for the CD-LTA are indicated in Table 6-34 CD-LTA Indications. Each LED is listed with its associated function and LED and Operational status. Refer to Figure 6-22 CD-LTA Blade on page 6-66 for the location of the LEDs on the blade.
Page 381: Table 6-35 Cd-Lta Rj11 Cable Connector Pin-Outs
UNIVERGE SV8100/SV8300 Issue 1.0 4.5.4 Connectors Table 6-35 CD-LTA RJ11 Cable Connector Pin-Outs on page 6-69 shows the pin-outs for the RJ-61 connector. Refer to Figure 6-22 CD-LTA Blade on page 6-66 for an illustration showing the location of the connectors on the CD-LTA blade.
Page 382 ECTION CD-4COTB (4 Loop and Ground Start Interface) Figure 6-23 CD-4COTB Blade 5.1.1 Description The CD-4COTB blade is common to both UNIVERGE SV8100/ SV8300 systems. The COIU blade provides: CD-4COTB: Four analog loop start/ground start trunk circuits 6 - 70...
Page 383: Table 6-36 Cd-4Cotb Maximum Upgrade Capacities
UNIVERGE SV8100/SV8300 Issue 1.0 One trunk status LED One Blade status LED Four Caller ID Circuits Two Power Failure Transfer Circuits Connection for COIDB Daughter Board The 4COIU blade consumes four trunk ports ranging between ports 001~200. The CN2 connector provides connection to four analog trunk ports, which are polarity sensitive (tip-to-tip, ring-to-ring).
Page 384: Figure 6-23 Cd-4Cotb Blade
Issue 1.0 UNIVERGE SV8100/SV8300 5.1.2 Installation Install the COIU blade into an available slot in the chassis. (Refer to Figure 6-23 CD-4COTB Blade on page 6-70 for a layout of the blade.) If the PZ-4COTF is to be used, install this prior to inserting the CD-4COTB blade into the chassis.
Page 385: Table 6-38 Cd-4Cotb Rj-61 Cable Connector Pin-Outs
UNIVERGE SV8100/SV8300 Issue 1.0 5.1.4 Connectors Table 6-38 CD-4COTB RJ-61 Cable Connector Pin-Outs on page 6-73 shows the pin-outs for the RJ-61 connector. Refer to Figure 6-23 CD-4COTB Blade on page 6-70 for an illustration showing the location of the connectors on the 4COIU blades.
Page 386: Figure 6-24 Installing The Pz-4Cotf Daughter Board
Issue 1.0 UNIVERGE SV8100/SV8300 PZ-4COTF (4 Loop and Ground Start Interface Daughter Board) Figure 6-24 Installing the PZ-4COTF Daughter Board 5.2.1 Description The PZ-4COTF daughter board is common to both UNIVERGE SV8100/SV8300 systems. The PZ-4COTF blade provides: PZ-4COTF: Four analog loop start/ground start trunk circuits...
Page 387: Table 6-39 Pz-4Cotf Maximum Upgrade Capacities
UNIVERGE SV8100/SV8300 Issue 1.0 Connector for COIU Blade Connector for CD-LTA The PZ-4COTF consumes four trunk ports ranging between ports 001~200. The CN2 connector provides connection to four analog trunk ports, which are polarity sensitive (tip-to-tip, ring-to-ring). The power failure circuits (CN3), however, are not polarity sensitive.
Page 388: Table 6-40 Pz-4Cotf Rj-61 Cable Connector Pin-Outs
Issue 1.0 UNIVERGE SV8100/SV8300 5.2.2 Installation To install the PZ-4COTF Four plastic spacers are included with the COIDB. Install the plastic spacers on the CD-4COTB or CD-LTA blade. Make sure to attach the spacers so that they extend out on the side of the daughter board which has the CN1 connector.
Page 389 UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-40 PZ-4COTF RJ-61 Cable Connector Pin-Outs (Continued) RJ-61 Cable Connector CN2, Trunks – Connecting to CD-LTB/CD-LTA Blade The CN2 connector is polarity sensitive (tip-to-tip, ring-to-ring). Pin No. Connection Circuit 4 – Tip Circuit 3 – Tip Circuit 2 –...
Page 390: Figure 6-25 Cd-2Bria Blade
UNIVERGE SV8100/SV8300 CD-2BRIA (2 Basic Rate Interface) Figure 6-25 CD-2BRIA Blade 5.3.1 Description The CD-2BRIA blade is common to both UNIVERGE SV8100/ SV8300 systems. This unit is an interface unit that accommodates an ISDN (Basic Rate) circuit. 6 - 78...
Page 391: Table 6-41 Cd-2Bria Maximum Upgrade Capacities
UNIVERGE SV8100/SV8300 Issue 1.0 The BRI blade provides: Two (CD-2BRIA) 2-Channel Circuits (2B + D) configured as T-Bus 64 Kb/s Clear B-Channel and 16 Kb/s D-Channel Two Status LEDs Connector for PZ-2BRIA These trunk circuits T-Bus (SV8100) or S-Bus (SV8300 only) can be connected to either ISDN trunks or ISDN telephones, depending on the switch setting within system programming.
Page 392: Table 6-42 Cd-2Bria Led Indications
Issue 1.0 UNIVERGE SV8100/SV8300 With normal operation, the status LED flashes fast. If trouble was found during the self diagnostics routine, the status LED flashes slow. Once connected, the ISDN Layer Link Status LEDs are on steady when the Layer I link is established.
Page 393: Table 6-43 Cd-2Bria Rj-45 T-Bus Cable Connector Pin-Outs
UNIVERGE SV8100/SV8300 Issue 1.0 5.3.4 Connectors Table 6-43 CD-2BRIA RJ-45 T-Bus Cable Connector Pin-Outs show the pin-outs for the RJ-45 cable connector for S-Bus and T-Bus connections. Refer to Figure 6-25 CD-2BRIA Blade on page 6-78 an illustration showing the location of the connectors on the CD-2BRIA blade.
Page 394: Figure 6-26 Installing The Pz-2Bria Daughter Board
Issue 1.0 UNIVERGE SV8100/SV8300 PZ-2BRIA (2 Basic Rate Interface Daughter Board) Figure 6-26 Installing the PZ-2BRIA Daughter Board 6 - 82 Installing the SV8100/SV8300 Blades...
Page 395: Table 6-44 Pz-2Bria Maximum Upgrade Capacities
All ISDN telephone circuits [#1-2 (BRI blade) and #3-4 (with the BRI daughter board)] are supplied DC power from the UNIVERGE SV8100/SV8300s systems. System programming must be used to block new calls on the blade.
Page 396: Table 6-45 Pz-2Bria Rj-45 T-Bus Cable Connector Pin-Outs
Issue 1.0 UNIVERGE SV8100/SV8300 Before proceeding to Step 3, wait to verify that the STATUS LED starts to flash. With normal operation, the status LED flashes fast. If trouble was found during the self diagnostics routine, the status LED flashes slow.
Page 397: Figure 6-27 Cd-4Diopa Blade
CD-4DIOPA (DID/OPX Interface) Figure 6-27 CD-4DIOPA Blade 5.5.1 Description The CD-4DIOPA blade is common to both UNIVERGE SV8100/ SV8300 systems. The CD-4DIOPA supports the analog DID and single line telephone interface functions (such as Off-Premise Extension). The function type is assigned in programming for each port. The circuit types, however, should be grouped together.
Page 398: Table 6-46 Cd-4Diopa Maximum Upgrade Capacities
Issue 1.0 UNIVERGE SV8100/SV8300 The CD-4DIOPAprovides: Four (4DIOPU) DID trunk circuits or four OPX circuits Two Blade status LEDs Table 6-46 CD-4DIOPA Maximum Upgrade Capacities provides the maximum capacities for the CD-4DIOPA blades when they are upgraded. Table 6-46 CD-4DIOPA Maximum Upgrade Capacities 19”...
Page 399: Table 6-48 Cd-4Diopa Rj-61 Cable Connector Pin-Outs
UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-47 CD-4DIOPA LED Indications (Continued) LED Indication Operation Status Remarks Live LED Busy LED (Green) (Red) A Channel is busy (use – Unit Busy another from CH1 ~ CHx). All channels are idle. – Flash (100ms Downloading firmware.
Page 400: Figure 6-28 Cd-Prta Blade (Front And Side View)
Figure 6-28 CD-PRTA Blade (Front and Side View) 5.6.1 Description The CD-PRTA blade is common to both UNIVERGE SV8100/ SV8300 systems. The CD-PRTA T1/PRI blade provides an interface for T1 and ISDN Primary Rate Interface (PRI) applications. This blade has a single 24-channel 64Kb per second digital signal circuit that can be configured for either T1 trunks or PRI.
Page 401: Table 6-49 Cd-Prta Maximum Upgrade Capacities
UNIVERGE SV8100/SV8300 Issue 1.0 If set for T1, the T1/PRI blade provides 24 trunks in a single universal slot. These trunks can be one of the following: Loop Start Ground Start E&M Trunks ANI/DNIS E&M Trunks T1 provides the system the advantage of advanced digital trunking and conserving universal slots.
Page 402 Issue 1.0 UNIVERGE SV8100/SV8300 5.6.2 Installation To install the CD-PRTA: Plug the CD-PRTA into any universal slot on the chassis. Use Program 10-51-01 (PRI/T-1) to set the CD-PRTA blade to either PRI or T-1. With normal operation, LED 1 flashes green.
Page 403: Figure 6-29 Pri Layout For Nt-1 Network
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 6-29 PRI Layout for NT-1 Network 5.6.3 LED Indications LED indications for the CD-PRTA are listed in Table 6-50 CD-PRTA Indications. Each LED is listed with its associated function and LED and Operational status. Refer to...
Page 404: Figure 6-30 Cd-Prta Led Indication Pattern Of Layer 1 On T1 Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 6-30 CD-PRTA LED Indication Pattern of Layer 1 on T1 Unit 5.6.4 Connectors Table 6-51 CD-PRTA RJ-45 Cable Connector Pin-Outs shows the pin-outs for the RJ-45 connector. Refer to Figure 6-28 CD-PRTA Blade (Front and Side View) on page 6-88 for an illustration showing the location of the connectors on the PRIU blade.
Page 405: Table 6-52 Cd-Prta Rj48C Connector Pin-Outs
UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-52 CD-PRTA RJ48C Connector Pin-outs shows the pin-outs for the 8-pin RJ48C connector for the network and terminal interfaces. Table 6-52 CD-PRTA RJ48C Connector Pin-outs Network Interface Terminal Interface Pinout for the 8-Pin Pinout for the 8-Pin...
Page 406: Figure 6-31 Cd-4Odta Blade
Issue 1.0 UNIVERGE SV8100/SV8300 CD-4ODTA (4-Port Tie Line Interface Blade) Figure 6-31 CD-4ODTA Blade 5.7.1 Description The CD-4ODTA Tie Line blade is an out band dial type analog tie line interface blade. This blade supports system connections to either 2-wire (four lead, tip/ring) or 4-wire (eight lead, tip/ring/tip 1/ ring 1) E&M signalling tie lines (determined in Program 10-13...
Page 407: Table 6-53 Cd-4Odta Maximum Upgrade Capacities
Two straps and one switch per circuit to determine the circuit type Limitation depends on the connecting Router, Multiplexer or Exchange. If the UNIVERGE SV8100/SV8300 is connected to another UNIVERGE SV8100/SV8300 directly, there is up to 1,500 ohms loop resistance (including system). Table 6-53 CD-4ODTA Maximum Upgrade Capacities provides the maximum capacities for the ODT blades when they are upgraded.
Page 408: Table 6-54 Cd-4Odta Led Indications
Issue 1.0 UNIVERGE SV8100/SV8300 5.7.3 LED Indications LED indications for the CD-4ODTA are listed in Table 6-54 CD-4ODTA LED Indications. Each LED is listed with its associated function and LED and Operational status. Refer to Figure 6-31 CD-4ODTA Blade on page 6-94 for the location of the LEDs on the blade.
Page 409 UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-55 CD-4ODTA RJ-61 Cable Connector Pin-Outs RJ-61 Cable Connector – 2-Wire E&M, CN1A~CN1D Pin No. Connection Description — Not Used Control signal to trunk — Not Used Voice signal both ways Voice signal both ways —...
Page 410 Issue 1.0 UNIVERGE SV8100/SV8300 5.7.5 Connections Figure 6-32 Voice Signal Connection for Type I And V on page 6-98 Figure 6-33 Control Signal Connection on page 6-99 show the signaling methods for circuit types. Figure 6-32 Voice Signal Connection for Type I And V...
Page 411: Figure 6-33 Control Signal Connection
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 6-33 Control Signal Connection System Hardware Manual 6 - 99...
Page 412: Figure 6-34 Cd-Vm00 Blade
Description The CD-VM00 blade is common to both UNIVERGE SV8100/ SV8300 systems. This blade is a PC platform installed in the UNIVERGE SV8100/ SV8300 that contains data storage for voice recording and application software supporting a maximum of 16 ports.
Page 413: Figure 6-35 Install The Cr-2032 Battery
UNIVERGE SV8100/SV8300 Issue 1.0 Automatic Gain Control (AGC) Two USB 1.0 ports for USB keyboard support, database backup and software upgrades One 15-pin VGA connector for VHA monitor support 6.1.2 Installation Only one CD-VM00 can be installed per system. Handle the drive and DSP carefully. To prevent damage, do not drop the drive or apply pressure to it.
Page 414: Figure 6-36 Install The So-Dimm Memory
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 6-36 Install the SO-DIMM Memory Install the Compact Flash drive into slot CN7, make sure the drive is fully seated in the slot (refer to Figure 6-37 Install the Compact Flash Drive). Figure 6-37 Install the Compact Flash Drive 6.1.3...
Page 415 UNIVERGE SV8100/SV8300 Issue 1.0 6.1.3.2 Busy LED – Red The Busy LED is controlled by the DSP and indicates the port status. Off: Power off or idle. On: Reset. Flash: Indicates how many ports on the VM Card are currently in use. Faster flash rates indicate heavier use.
Page 416: Figure 6-38 Cd-Vm00 Db9 To 6-Pin Modular Rs-232 Adapter
Issue 1.0 UNIVERGE SV8100/SV8300 6.1.4.2 DB9 to 6-pin Modular RS-232 Adapter Figure 6-38 CD-VM00 DB9 to 6-Pin Modular RS-232 Adapter 6.1.4.3 RS-232 Serial Cable (DTE) Figure 6-39 CD-VM00 RS-232 Serial Cable (DTE) 6 - 104 Installing the SV8100/SV8300 Blades...
Page 417: Figure 6-40 Cd-Vm00 Rs-232 Serial Cable (Dce)
UNIVERGE SV8100/SV8300 Issue 1.0 6.1.4.4 RS-232 Serial Cable (DCE) Figure 6-40 CD-VM00 RS-232 Serial Cable (DCE) 6.1.4.5 USB Interface The APSU provides two USB interfaces that are in full compliance with the Universal Serial Bus Specification, Revision 2.0. The connections to the USB interface are through a dual Type-A plug connector.
Page 418: Table 6-56 Ethernet Connector Pin-Out
Issue 1.0 UNIVERGE SV8100/SV8300 On the APSU, 5V shall be provided to the VGA connector in a manner where it can be removed from the connector via component depopulation to reduce current draw on the 5V power supply should this feature not be needed.
Page 419: Figure 6-41 Cd-Pvaa Blade
CD-PVAA (Conference Bridge) Figure 6-41 CD-PVAA Blade 6.2.1 Description The CD-PVAA blade is common to both UNIVERGE SV8100/ SV8300 systems. The Packet Voice Application, CD-PVAA blade is an optional interface that supports Application Packages (Univerge Multimedia Conference Bridge, and Interactive Voice Response Application).
Page 420 Issue 1.0 UNIVERGE SV8100/SV8300 A digital signal processor/voice processing section handles the following functions: DTMF detection DTMF generation General tone detection Automatic Gain Control (AGC) Basic Support Package Each blade installed with the CNF or IVR package accounts for up to 16 Extension Ports of the Total Port capacity (One Conference or One IVR blade maximum).
Page 421 UNIVERGE SV8100/SV8300 Issue 1.0 Fast Flash: Board is in sync with the chassis and operating normally Busy LED – Red On: Application problem CompactFlash Card Activity LED – Red CompactFlash Card Activity LED is controlled by the IDE controller and indicates read/write activity on the CompactFlash card.
Page 422: Figure 6-42 Cd-Ccta Blade
CD-CCTA (CCIS Trunk Interlace) Figure 6-42 CD-CCTA Blade 6.3.1 Description The CD-CCTA blade is common to both UNIVERGE SV8100/ SV8300 systems. The Common Channel Handler Interface blade is a digital trunk ETU that terminates FT1 trunks (up to 24 DS-0 channels) providing a common channel signal interface.
Page 423: Table 6-57 Cd-Ccta Led Indications
UNIVERGE SV8100/SV8300 Issue 1.0 6.3.2 Installation Install the CD-CCTA in any universal slot. 6.3.3 LED Indications LED indications for the CD-CCTA are listed in Table 6-57 CD-CCTA Indications. Each LED is listed with its associated function and LED and Operational status. Refer to...
Page 424: Figure 6-43 Cd-Ccta Led Indication Pattern Of Layer 1 On T1 Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 6-43 CD-CCTA LED Indication Pattern of Layer 1 on T1 Unit 6.3.4 Connectors Table 6-58 CD-CCTA RJ-45 Cable Connector Pin-Outs shows the pin-outs for the RJ-45 connector. Refer to Figure 6-42 CD-CCTA Blade on page 6-110 for an illustration showing the location of the connectors on the CD-CCTA blade.
Page 425: Figure 6-44 Cd-Rtb Blade
UNIVERGE SV8100/SV8300 Issue 1.0 CD-RTB (4-Port Router) Figure 6-44 CD-RTB Blade 6.4.1 Description This blade is common for both the UNIVERGE SV8100/SV8300 systems. System Hardware Manual 6 - 113...
Page 426 Issue 1.0 UNIVERGE SV8100/SV8300 The Router blade is a 4-port switching hub which complies with the ethernet specification for both 100Base-TX and 10Base-T. This blade is compatible in LAN applications using 10Mbps and 100Mbps. All ports automatically identify and switch 100Base-TX, 10Base-T and Full/Half Duplex.
Page 427: Table 6-59 Cd-Rtb Maximum Upgrade Capacities
IP telephone and it allows for centralized power backup. 6.4.2 Installation To install the CD-RTB: Plug the CD-RTB blade into any universal slot. Refer to the Univerge SV8100 Programming Manual for required programming. System Hardware Manual 6 - 115...
Page 428: Table 6-60 Cd-Rtb Led Indications
Issue 1.0 UNIVERGE SV8100/SV8300 6.4.3 LED Indications LED indications for the CD-RTB are indicated in Table 6-60 CD-RTB Indications. Each LED is listed with its associated function and LED and Operational status. Refer to Figure 6-44 CD-RTB Blade on page 6-113 for the location of the LEDs on the blade.
Page 429: Cd-Etia (Gigabit Poe Switch)
Figure 6-45 CD-ETIA Blade 6.5.1 Description The CD-ETIA blade is common to both UNIVERGE SV8100/SV8300 systems. The CD-ETIA blade is a managed 8-port gigabit ethernet PoE switch. Ports 1 and 8 are the default uplink ports. All the user management and stacking is based on this setup.
Page 430: Installation
Issue 1.0 UNIVERGE SV8100/SV8300 802.1Q VLANs 802.1p Priority Queuing Port Mirroring 802.3x Flow Control Independent VLAN Learning Support TCP/IP Networking Stack Multi-Unit Stacking (multiple blades in a system are managed from the same user interface) Dynamic PoE Control (allows setting the proper PoE classifications for...
Page 431: Cd-Cp00-Usip Address Assignment
UNIVERGE SV8100/SV8300 Issue 1.0 6.5.2.2 CD-CP00-USIP Address Assignment The GSWU Main board will be provided with an IP address from the back plane CPU during the initialization sequence. The provision of an IP address from the back plane will identify the Main board. If during initialization, the IP address is set to 0 by the CPU, the blade is then determined to be an Add-on.
Page 432: Unmanaged Switch Functions
The grouping of the three GSWU units to form a 20 port switch is restricted to reside in a single system location. The grouping is not allowed where the GSWU units are placed as part of the NetLink feature in the Univerge SV8100 system. 6.5.2.5...
Page 433: Cabling And Mdf Connection
Wiring Between the Chassis and the MDF 7.3.1 Chassis Cables The chassis is equipped with two MDF Cable Assemblies. NEC recommends that the MDF Cable Assembly be used to connect the multiline terminals, single line telephones (except PFT), PVAA and DID/OPX lines.
Page 434: Table 6-62 Mdf Cable Colors
Issue 1.0 UNIVERGE SV8100/SV8300 Table 6-62 MDF Cable Colors Cable Colors Outs BR–WH GN–RD BR–BK BL–YL SL–YL BR–VI GN–WH OR–RD BL–BK SL–BK BR–YL GN–VI OR–WH BL–RD SL–RD BR–GN GN–YL OR–VI WH–BL WH–SL RD–BR BK–GN YL–OR VI–BL BL–WH SL–WH BR–RD GN–BK OR–YL...
Page 435 UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-63 MDF Cable Connections (Station) (Continued) DLCA Station Running Connector Cable Cable DLCA COTB RD–BR TA–1 BR–RD TB–1 RD–SL RA–1 SL–RD RB–1 BK–BL TA–2 BL–BK TB–2 BK–OR RA–2 OR–BK RB–2 BK–GN TA–1 GN–BK TB–1 BK–BR RA–1...
Page 436 Issue 1.0 UNIVERGE SV8100/SV8300 Table 6-64 MDF Cable Connections (Trunk) COTB DIOPA PRTA Station Running Connector Cable BRIA CCTA Cable WH–BL TA–1 BL–WH TB–1 WH–OR – – RA–1 – OR–WH RB–1 WH–GN TA–2 GN–WH – – TB–2 – WH–BR –...
Page 437: Outside Lines
UNIVERGE SV8100/SV8300 Issue 1.0 Table 6-64 MDF Cable Connections (Trunk) (Continued) COTB DIOPA PRTA Station Running Connector Cable BRIA CCTA Cable VI–BL TA–1 BL–VI TB–1 VI–OR – – RA–1 – OR–VI RB–1 VI–GN TA–2 GN–VI – – TB–2 – VI–BR –...
Page 438 Issue 1.0 UNIVERGE SV8100/SV8300 - - NOTES - - 6 - 126 Installing the SV8100/SV8300 Blades...
Page 439: General Description
Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline Terminals ENERAL ESCRIPTION ECTION This chapter provides information about the DT300/DT700 Series digital Chapter and IP terminals in addition to the single line telephones, cordless telephones and wireless telephones. Table 7-1 Terminal Category Reference Chart DT300/DT700 Series Terminals Category Equipment...
Page 440: Table 7-2 Terminal And Adapter Compatibility
Issue 1.0 UNIVERGE SV8100/SV8300 The easy-to-use adjustable footplate allows for a variety of height positions. There are several easy-to-read LCD displays available, including a new large color touch panel LCD. The following tables list each terminal and the options available.
Page 441: Table 7-3 Terminal And Line Key/Lcd Compatibility
UNIVERGE SV8100/SV8300 Issue 1.0 Table 7-3 Terminal and Line Key/LCD Compatibility Line Key/LCD Terminal 8 LK-L 8LKD(LD)-L 8LKI(LD)-L 12LK-L LCD (BL-L DCL-60 IP Terminals: ITL-2E-1 (BK) TEL –— –— –— –— –— –— ITL-6DE-1 (BK) TEL –— –— –— –—...
Page 442: Table 7-4 Terminal And Tenkey Kit Compatibility
Issue 1.0 UNIVERGE SV8100/SV8300 Table 7-4 Terminal and Tenkey Kit Compatibility Tenkey Kit Terminal BS(F)-L BS(S)-L BS(ACD)-L BS(Braille)-L BS(Retro)-l IP Terminals: ITL-2E-1 (BK) TEL –— –— –— –— ITL-6DE-1 (BK) TEL –— –— –— –— ITL-8LD-1 (BK)/(WH) TEL ITL-12D-1 (BK)/(WH) TEL...
Page 443: Table 7-5 Terminal And Optional Equipment Compatibility
UNIVERGE SV8100/SV8300 Issue 1.0 Table 7-5 Terminal and Optional Equipment Compatibility Equipment Terminal PSA-L PANEL-L WM-L IP Terminals: ITL-2E-1 (BK) TEL –— ITL-6DE-1 (BK) TEL –— ITL-8LD-1 (BK)/(WH) TEL ITL-12D-1 (BK)/(WH) TEL ITL-12PA-1 (BK) TEL –— ITL-24D-1 (BK)/(WH) TEL ITL-32D-1 (BK)/(WH) TEL...
Page 444: Dt300 Series Digital Multiline Terminals
Issue 1.0 UNIVERGE SV8100/SV8300 DT300 S ERIES IGITAL ULTILINE ERMINALS ECTION The DT300 Series offers a new exciting line up of digital telephones. These telephones (except economy), have a modular design that allows the telephones to be upgraded and customized. Optional LCD panels, dial pads, feature key kits, handset cradles, face plates and colored side panels can easily be snapped on and off to upgrade and customize as the customer desires.
Page 445: Dtl-6De-1 (Bk) Tel
UNIVERGE SV8100/SV8300 Issue 1.0 2.1.2 DTL-6DE-1 (BK) TEL This digital economy Multiline Terminal has six line keys with display and is available in black only. The terminal features: Non-modular design Four step adjustable base Half-duplex speaker phone Six line keys (Red, Green)
Page 446: Figure 7-3 Dtl-8Ld-1 Tel
Issue 1.0 UNIVERGE SV8100/SV8300 Backlit 10-key dial pad for easy viewing Full-duplex handsfree operation Figure 7-3 DTL-8LD-1 TEL 2.1.4 DTL-12D-1 (BK) TEL/DTL-12D-1 (WH) TEL This digital value Multiline Terminal has 12 line keys and is available in both black and white. The terminal features:...
Page 447: Figure 7-4 Dtl-12D-1 Tel
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 7-4 DTL-12D-1 TEL 2.1.5 DTL-12PA-1 (BK) TEL This digital value multiline terminal with Analog Power Failure adapter has 12 line keys and is available in black only. The terminal features: Modular design Four step adjustable base...
Page 448: Figure 7-5 Dtl-12Pa-1 Tel
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 7-5 DTL-12PA-1 TEL 2.1.6 DTL-24D-1 (BK) TEL/DTL-24D-1 (WH) TEL This digital value Multiline Terminal has 24 line keys and is available in both black and white. The terminal features: Modular design Four step adjustable base...
Page 449: Figure 7-6 Dtl-24D-1 Tel
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 7-6 DTL-24D-1 TEL 2.1.7 DTL-32D-1 (BK) TEL/DTL-32D-1 (WH) TEL This digital value Multiline Terminal has 32 line keys (24 line keys plus eight line key LK Unit) and is available in both black and white.
Page 450: Figure 7-7 Dtl-32D-1 Tel
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 7-7 DTL-32D-1 TEL 7 - 12 Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline Terminals...
Page 451: Figure 7-8 Itl-2E-1 Tel
UNIVERGE SV8100/SV8300 Issue 1.0 DT700 S IP M ERIES ULTILINE ERMINALS ECTION The DT700 Series offers a new exciting line up of IP telephones. These telephones (except economy), have a modular design that allows the telephones to be upgraded and customized. Optional LCD panels, dial pads, feature key kits, handset cradles, face plates and colored side panels can easily be snapped on and off to upgrade and customize as the customer desires.
Page 452: Figure 7-9 Itl-6De-1 Tel
Issue 1.0 UNIVERGE SV8100/SV8300 3.1.2 ITL-6DE-1 (BK) TEL This IP economy Multiline Terminal has six line keys with display and is available in black only. The terminal features: Non-modular design Four step adjustable base Remote login and maintenance Full-duplex speaker phone...
Page 453: Figure 7-10 Itl-8Ld-1 Tel
UNIVERGE SV8100/SV8300 Issue 1.0 Two 224 X 96 full dot gray scale LCDs with cursor keys Backlit 10-key dial pad for easy viewing Full-duplex handsfree operation Wideband handset IEEE 802.3af compliant XML open interface 10Base-T/100Base-TX network interface Backlit LCD Figure 7-10 ITL-8LD-1 TEL 3.1.4...
Page 454: Figure 7-11 Itl-12D-1 Tel
Issue 1.0 UNIVERGE SV8100/SV8300 XML open interface 10Base-T/100Base-TX network interface Backlit LCD Figure 7-11 ITL-12D-1 TEL 3.1.5 ITL-12PA-1 (BK) TEL This IP value Multiline Terminal with Analog Power Failure adapter has 12 line keys and is available in black only. The terminal features:...
Page 455: Figure 7-12 Itl-12Pa-1 Tel
UNIVERGE SV8100/SV8300 Issue 1.0 Backlit LCD PSA Adapter for Power Failure Figure 7-12 ITL-12PA-1 TEL 3.1.6 ITL-24D-1 (BK) TEL/ITL-24D-1 (WH) TEL This IP value Multiline Terminal has 24 line keys and is available in both black and white. The terminal features:...
Page 456: Figure 7-13 Itl-24D-1 Tel
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 7-13 ITL-24D-1 TEL 3.1.7 ITL-32D-1 (BK) TEL/ITL-32D-1 (WH) TEL This IP value Multiline Terminal has 32 line keys (24 line keys plus an eight line key LK Unit) and is available in both black and white.
Page 457: Figure 7-14 Itl-32D-1 Tel
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 7-14 ITL-32D-1 TEL 3.1.8 ITL-320C-1 (BK) TEL This IP Multiline Terminal features a large color touch panel LCD and is available in black only. The terminal features: Modular design Four step adjustable base Full-duplex speaker phone...
Page 458: Figure 7-15 Itl-320C-1 Tel
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 7-15 ITL-320C-1 TEL 7 - 20 Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline Terminals...
Page 459: Figure 7-16 Connecting A Multiline Terminal To The System
UNIVERGE SV8100/SV8300 Issue 1.0 NSTALL ULTILINE ERMINALS ECTION Connecting the DT300 Series Multiline Terminal to the System This instruction applies to all DT300 Series Multiline Terminals. Plug the telephone cord into the modular jack on the bottom side of the Multiline Terminal.
Page 460: Figure 7-17 Leading Line Cords On A Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 Lead the Line and Handset cables through the applicable grooves. Groove for Line and Handset Cables Figure 7-17 Leading Line Cords on a Multiline Terminal Applying Power to the DT700 Multiline Terminals The DT700 terminals support two different methods to power the terminal:...
Page 461: Figure 7-18 Ip Terminal Connector Locations
UNIVERGE SV8100/SV8300 Issue 1.0 Connecting the IP Multiline Terminal to the Network and PC These instructions for connecting an IP Multiline Terminal to the Network and PC apply to DT700 Multiline Terminals. Refer to Figure 7-18 IP Terminal Connector Locations.
Page 462: Figure 7-19 Typical Network Ip Connection
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 7-19 Typical Network IP Connection Adjusting the LCD on the Multiline Terminal DT300/DT700 Series display Multiline Terminals have an adjustable Liquid Crystal Display (LCD). The LCD can be adjusted by pulling up or pushing down as desired.
Page 463: Figure 7-21 12Lk-L Kit
UNIVERGE SV8100/SV8300 Issue 1.0 Installing Line Key Kit (12LK-L KIT The 12LK-L KIT Provides twelve additional buttons to ITL or DTL multiline terminals. The 12LK-L KIT kit: Mounts directly to top side of terminal Supports Red and Green LED colors Figure 7-21 12LK-L Kit 4.5.1...
Page 464: Figure 7-22 Removing The Line Key Panel
Issue 1.0 UNIVERGE SV8100/SV8300 Line Key Panel Figure 7-22 Removing the Line Key Panel Lift and remove the DESI sheet. DESI Sheet Figure 7-23 Removing the DESI Sheet Press the right end of the Line Key placeholder and lift to...
Page 465: Figure 7-24 Removing The Line Key Placeholder
UNIVERGE SV8100/SV8300 Issue 1.0 Press here then Lift Figure 7-24 Removing the Line Key Placeholder Install the 12LK-L KIT and press down until click is heard. 12LK-L KIT Figure 7-25 Installing the 12LK-L KIT System Hardware Manual 7 - 27...
Page 466: Figure 7-26 Installing The Desi Sheet
Issue 1.0 UNIVERGE SV8100/SV8300 If desired, print and install the new DESI sheet. Figure 7-26 Installing the DESI Sheet Install the supplied Line Key Panel (refer to Figure 7-27 Installing the Line Key Panel). Line Key Panel Figure 7-27 Installing the Line Key Panel Install the side panel.
Page 467: Table 7-6 Numbered Keypad Type
UNIVERGE SV8100/SV8300 Issue 1.0 4.5.2 Configuring the Digital Telephone for the Correct Number of Line Keys With the telephone not plugged in and the handset on-hook, press the 4 and 6 buttons on the numbered keypad and connect the telephone cable.
Page 468: Table 7-7 Keypad Kit Type
Issue 1.0 UNIVERGE SV8100/SV8300 Press Soft Key 2 for Key Kit Type. Select the type of keypad kit being used by pressing the Up/ Down key. Table 7-7 Keypad Kit Type Keypad Kit Entry Description Kit1 Type A – Japan with cursor key Kit2 Type A –...
Page 469: Installing The Directory Card On The Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 Continue pressing Soft Key 4 to exit (Exit-Exit-Save). The terminal will reset automatically. Installing the Directory Card on the Multiline Terminal A directory card can be attached to DT300/DT700 Series Multiline Terminals. The directory card can be used to record often dialed numbers or other important information.
Page 470: Installing A Numbered Keypad On The Multiline Terminal
IPK II and IPS terminals. Standard Numbered Keypad The standard keypad (in black or white), is commonly delivered with the UNIVERGE SV8100/SV8300 terminal (refer to Figure 7-30 Standard Numbered Keypad on page 7-33).
Page 471: Figure 7-30 Standard Numbered Keypad
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 7-30 Standard Numbered Keypad BS (Retro)-L KIT The optional Retro keypad (in black or white), is compatible with the term Series i telephone, allowing the terminal to be used with the IPK II and IPS multiline terminals.
Page 472: Installing The Numbered Keypad On A Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 4.7.1 Installing the Numbered Keypad on a Multiline Terminal To prevent possible damage to the Numbered Keypad or the DTL/ITL multiline terminal during installation or removal, disconnect the line cord/ LAN cable and the AC/DC adapter from the DTL/ ITL multiline terminal.
Page 473: Figure 7-35 Install Plastic Panels
UNIVERGE SV8100/SV8300 Issue 1.0 Slide the replacement numbered keypad into the grooves located on the inside of the telephone, then press down on the keypad to snap it into place. See Figure 7-34 Install New Numbered Keypad into DT300/DT700 Series Terminal.
Page 474: Configuring The Digital Telephone For The Numbered Keypad
Issue 1.0 UNIVERGE SV8100/SV8300 4.7.2 Configuring the Digital Telephone for the Numbered Keypad With the telephone not plugged in and the handset on-hook, press the 4 and 6 buttons on the numbered keypad and connect the telephone cable. This places the telephone into Service Class R/W mode. The MW LED should be lit.
Page 475: Table 7-10 Keypad Kit Type
UNIVERGE SV8100/SV8300 Issue 1.0 At the Login screen, enter the user name (default = ADMIN) and password (default = 6633222) and press the OK Soft Key. Press Soft Key 3 for Maintenance Setting. Press Soft Key 4 for Adjust. Press Soft Key 2 for Key Kit Type.
Page 476: Adjusting The Height On The Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 Table 7-11 Line Key Kit Type (Continued) Line Key Kit Entry Description Kit6 Value 6-Button Kit2 Value 2-Button Kit0 IP-CTS Press Soft Key 4 for OK to complete. Continue pressing Soft Key 4 to exit (Exit-Exit-Save). The terminal will reset automatically.
Page 477: Removing Or Installing The Tilt Legs On The Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 Removing or Installing the Tilt Legs on the Multiline Terminal The Tilt Legs can be removed or installed on the DT300/DT700 Series multiline terminal. 4.9.1 Remove Tilt Legs Place the telephone on a flat surface (button side down).
Page 478: Install Tilt Legs
Issue 1.0 UNIVERGE SV8100/SV8300 Lift and remove the Tilt Legs. 4.9.2 Install Tilt Legs Place the telephone on a flat surface (button side down). Lay the adjustable Tilt legs on top of the telephone. See Figure 7-39 Attach Tilt Legs to DT300/DT700 Series Terminal.
Page 479: Figure 7-41 Adjust Height Of Dt300/Dt700 Series Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 7-40 Connecting the Tilt Legs Snap legs together and adjust to desired height. See Figure 7-41 Adjust Height of DT300/DT700 Series Terminal). Figure 7-41 Adjust Height of DT300/DT700 Series Terminal System Hardware Manual 7 - 41...
Page 480: Wall Mounting The Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 4.10 Wall Mounting the Multiline Terminal You can wall mount a DT300/DT700 Series connection Multiline Terminal using the base cover or an optional wall mount unit. A wall mount unit must be used if adapters are installed on the Multiline Terminal.
Page 481: Wall Mounting The Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 4.10.1.2 Wall Mounting the Multiline Terminal Plug line cord in the wall receptacle. Leave about eight inches of cord and bundle the rest as shown in Figure 7-44 Bundling the Line Cord. Figure 7-44 Bundling the Line Cord Ensure the Tilt Legs are in the flat (unused position).
Page 482: Removing The Multiline Terminal From The Wall Mounted Base Plate
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 7-46 Mount Multiline Terminal Wall on Wall Plate Push spare line cord behind the Multiline Terminal. 4.10.1.3 Removing the Multiline Terminal from the Wall Mounted Base Plate. To remove the Multiline Terminal, push up on the telephone until it comes loose.
Page 483: Wall Mounting The Base On A Switch Box
UNIVERGE SV8100/SV8300 Issue 1.0 4.10.1.4 Wall Mounting the Base on a Switch Box Locate the screw holes on the base and hang the cover over the screws on the switch box as illustrated in Figure 7-48 Wall Mounting Base on Switch Box.
Page 484: Dt300/Dt700 Series Terminal Options
Issue 1.0 UNIVERGE SV8100/SV8300 ULTILINE ERMINALS PTIONAL QUIPMENT ECTION DT300/DT700 Series Terminal Options The following chart provides a quick overview of the options available with the DT300/DT700 Series telephones. Table 7-12 Connectivity of Options IP Terminals Digital Terminals Value Value...
Page 485: Dt300/Dt700 Series Optional Terminal Equipment
UNIVERGE SV8100/SV8300 Issue 1.0 DT300/DT700 Series Optional Terminal Equipment 5.2.1 8LK-L (BK) UNIT/8LK-L (WH) UNIT Provides eight additional line keys to ITL or DTL terminals (except Economy). The unit features: Mounts directly to right side of terminal Supports Red and Green LED colors Figure 7-50 8LK-L UNIT 5.2.1.1...
Page 486: Figure 7-51 Remove Side Panel From Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 Pry the side panel from the multiline terminal. Side Panel Figure 7-51 Remove Side Panel from Multiline Terminal Return the multiline terminal to the buttons side up position. Fit the projections on the side of the 8LK-L UNIT into the guide holes on the side of the multiline terminal.
Page 487: 8Lkd (Ld)-L (Bk) Unit/8Lkd (Ld)-L (Wh) Unit
UNIVERGE SV8100/SV8300 Issue 1.0 Open the small door covering the side option connectors by pulling the cover handle to the front. Telephone Side Option Connection Cable Connector Cover Figure 7-53 Install the 8LK-L UNIT Cable Connect the cable from the 8LK-L UNIT to the side...
Page 488: Installing The 8Lkd (Ld)-L Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 7-54 8LKD (LD)-L UNIT 5.2.2.1 Installing the 8LKD (LD)-L UNIT To prevent possible damage to the 8LKD (LD)-L UNIT or the DTL multiline terminal during installation or removal, disconnect the line cord/LAN cable and the AC/DC adapter from the DTL multiline terminal.
Page 489: Figure 7-56 Ribbon Cable Connector
UNIVERGE SV8100/SV8300 Issue 1.0 Remove the screw (refer to Figure 7-55 Remove Side Panel from Multiline Terminal on page 7-50). Carefully, return the multiline terminal to the buttons side up position. Remove the soft keys and line key kit from the telephone.
Page 490: Figure 7-57 Ribbon Cable Installed
Issue 1.0 UNIVERGE SV8100/SV8300 Guide Projection Guide (One Each Side) Figure 7-57 Ribbon Cable Installed Align the projections on the bottom of the 8LKD (LD)-L UNIT into the guide holes on top of the multiline terminal. Slide the 8LKD (LD)-L UNIT toward the keypad...
Page 491: 8Lki (Ld)-L (Bk) Unit/8Lki (Ld)-L (Wh) Unit
UNIVERGE SV8100/SV8300 Issue 1.0 Holding the LCD in place, turn the multiline terminal button side down. Install the screw (refer to Figure 7-59 Install Screw). Screw Side Panel Figure 7-59 Install Screw Attach the side panel to the side of the 8LKD (LD)-L...
Page 492: Installing The 8Lki (Ld)-L Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 7-60 8LKI (LD)-L UNIT 5.2.3.1 Installing the 8LKI (LD)-L UNIT To prevent possible damage to the 8LKI (LD)-L UNIT or the ITL multiline terminal during installation or removal, disconnect the line cord/LAN cable and the AC/DC adapter from the ITL multiline terminal.
Page 493: Figure 7-62 Ribbon Cable Connector
UNIVERGE SV8100/SV8300 Issue 1.0 Remove the screw (refer to Figure 7-61 Remove Side Panel from Multiline Terminal on page 7-54). Carefully, return the multiline terminal to the buttons side up position. Remove the soft keys and line key kit from the telephone.
Page 494: Figure 7-63 Ribbon Cable Installed
Issue 1.0 UNIVERGE SV8100/SV8300 Guide Projection Guide (One Each Side) Figure 7-63 Ribbon Cable Installed Align the projections on the bottom of the 8LKI (LD)-L UNIT into the guide holes on top of the multiline terminal (refer to Figure 7-63 Ribbon Cable Installed).
Page 495: Dcl-60-1 (Bk) Console/Dcl-60-1 (Wh) Console
UNIVERGE SV8100/SV8300 Issue 1.0 Holding the LCD in place, turn the multiline terminal button side down. Install screw (refer to Figure 7-65 Install Screw). Screw Side Panel Figure 7-65 Install Screw Attach the side panel to the side of the 8LKI (LD)-L...
Page 496: Installing The Dcl-60-1 Console
Issue 1.0 UNIVERGE SV8100/SV8300 Keep the following in mind when installing DSS Consoles: A 60-Button DSS Console requires a separate digital station port when pairing with a digital keyset. For IP terminals, the console is connected to the side option slot using a special cable.
Page 497: Figure 7-67 Remove Side Panel From Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 Pry the side panel from the multiline terminal. Side Panel Figure 7-67 Remove Side Panel from Multiline Terminal Turn the multiline terminal button side up. Fit the projections of the supplied bracket into the side of the multiline terminal.
Page 498: Figure 7-69 Press Serial Cable Into Groove
Issue 1.0 UNIVERGE SV8100/SV8300 Carefully push the Serial cable into the Serial Cable Groove (ITL, DT700 only). Figure 7-69 Press Serial Cable into Groove Using the guides, slide the DCL-60-1 onto the installed bracket (refer to Figure 7-69 Press Serial Cable into Groove).
Page 499: Figure 7-71 Serial Cable Installed
UNIVERGE SV8100/SV8300 Issue 1.0 Open the small door covering the side option connectors by pulling the cover latch toward you (refer to Figure 7-71 Serial Cable Installed, ITL, DT700 only). Connect the cable from the DCL-60-1 CONSOLE to the Side Option Connector on the multiline terminal and close the cover (ITL, DT700 only).
Page 500: Lcd (Bl)-L (Bk) Unit/Lcd (Bl)-L (Wh) Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 7-72 Connect AC Adapter Cable Complete the installation by reattaching both plastic panels to the front of the multiline terminal. Figure 7-73 DCL-60-1 CONSOLE Installed 5.2.5 LCD (BL)-L (BK) UNIT/LCD (BL)-L (WH) UNIT The LCD (BL)-L UNIT is an optional LCD unit for modular terminals and supports the backlit LCD feature (DT300 Series only).
Page 501: Figure 7-74 Lcd (Bl)-L Unit
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 7-74 LCD (BL)-L UNIT 5.2.6 PANEL( )-L UNIT Optional plastic color side panels that allow users to customize the ITL/DTL terminals. The following colors are available for the Base (all), VLCD (Value LCD) and SLCD (Sophi LCD) terminals:...
Page 502: Figure 7-76 Attach The Wm-L Unit To Wall
Issue 1.0 UNIVERGE SV8100/SV8300 Attach the WM-L UNIT to the wall using four screws (refer to Figure 7-76 Attach the WM-L UNIT to Wall). Screws Screws Figure 7-76 Attach the WM-L UNIT to Wall Align the four cutouts with the four tabs on the WM-L UNIT...
Page 503: Figure 7-78 Wm-L Unit Installed
UNIVERGE SV8100/SV8300 Issue 1.0 Push down on telephone until the WM-L UNIT snaps into place (refer to Figure 7-78 WM-L UNIT Installed). Figure 7-78 WM-L UNIT Installed 5.2.8 Release the WM-L UNIT To release the telephone from the WM-L UNIT, press the...
Page 504: Figure 7-80 Plugging In Line Cord
Issue 1.0 UNIVERGE SV8100/SV8300 5.2.9 WM-L UNIT Attached to Wall Plate The WM-L UNIT (Wall Mount Unit) is used to attach any DT300/ DT700 Series multiline terminal to the wall plate This unit connects to the back side of the telephone.
Page 505: Figure 7-81 Cutouts For Wm-L Unit
UNIVERGE SV8100/SV8300 Issue 1.0 Cutouts Cutouts Figure 7-81 Cutouts for WM-L UNIT Push up on the WM-L UNIT until it snaps into place (refer to Figure 7-82 WM-L UNIT Installed). Figure 7-82 WM-L UNIT Installed System Hardware Manual 7 - 67...
Page 506: Figure 7-83 Mount Multiline Terminal Wall On Wall Plate
Issue 1.0 UNIVERGE SV8100/SV8300 Align the two holes on the back of the WM-L UNIT with the two screws on the wall plate and slide downward (refer to Figure 7-83 Mount Multiline Terminal Wall on Wall Plate). Figure 7-83 Mount Multiline Terminal Wall on Wall Plate Because of strength variation in switch boxes, this method is not recommended.
Page 507: Figure 7-85 Itl / Dtl Ptm Handset
Using the PTM handset on an NEC digital or IP terminal prevents eavesdropping and eliminates the worry that privileged information could be transmitted without user authority. These handsets are also an ideal solution to filter unwanted audio transmissions from environments with ambient background noise.
Page 508: Figure 7-87 Installing The Utr-1-1 Usb Handset Cable
UNIVERGE SV8100/SV8300 UTR-1-1 USB Handset The NEC USB telephone can be plugged directly into a PC USB port, enabling the high quality voice input and output capabilities of a standard desktop telephone. By connecting it to the USB port of a computer, calls can immediately be made and received using a SoftPhone without installation of additional software drivers.
Page 509: Figure 7-89 Wall Mounting The Utr-1-1 Usb Handset
UNIVERGE SV8100/SV8300 Issue 1.0 6.3.3 Wall Mounting The UTR-1-1 USB handset can be mounted on the wall using a wall plate or two screws. Align the two holes on the back of the UTR-1-1 and slide down onto the wall plate or screws.
Page 510: Figure 7-90 Installing Slt Adapter
Issue 1.0 UNIVERGE SV8100/SV8300 INGLE ELEPHONE ECTION Installing the SLT Adapter The Single Line Telephone adapter provides an interface for Single Line Telephones and other similar devices from an ESI channel. This adapter can be connected to any ESI port.
Page 511: Figure 7-91 Connecting The Slt Adapter
UNIVERGE SV8100/SV8300 Issue 1.0 Modular Terminal Modular Terminal SLTII(1)-U( ) ADP To ESIU Base Base CD-8DLCA or Cord Cord ESI Port ESI Port CD-16DLCA Modular Terminal Connections Modular Terminal Connections ESIU Port ESIU Single Line Telephone Connections Figure 7-91 Connecting the SLT Adapter Wall-Mounting the SLT Adapter Unplug the two line cords from the SLT Adapter.
Page 512: Figure 7-93 Attaching The Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Using the two screws provided with the SLT Adapter, attach the back cover to the desired location. Figure 7-93 Attaching the Unit Replace the front cover and the two screws removed in Step 2. Plug the two modular line cords back into the SLT Adapter which were removed in Step 1.
Page 513 Telephones ENERAL ESCRIPTION ECTION This chapter provides information regarding cordless telephones that can Chapter be used with the UNIVERGE SV8100/SV8300 system. CT-12 H EADSET ORDLESS ELEPHONE ECTION The CT-12 is a 2.4GHz cordless headset which connects to an analog port or an analog telephone line as a stand-alone unit or to an analog port adapter (APR, P/N 0890056).
Page 514: Selecting A Location
Issue 1.0 UNIVERGE SV8100/SV8300 The number of units which can be used on the system is greatly affected by the environment. The closer or smaller the area, the smaller the number of units which can be used. It is recommended to start with three or less. If there are no conflicts between the telephones, you can try adding additional units (up to five is the recommended maximum).
Page 515: Figure 8-2 Connecting The D Term Headset Cordless Base Unit To The Adapter
UNIVERGE SV8100/SV8300 Issue 1.0 Be sure that the base antenna can be fully extended. The base can be placed on a desk or tabletop or mounted on a standard telephone wall plate. Charge your new telephone for 15~20 hours before completing the installation or using the handset.
Page 516 Issue 1.0 UNIVERGE SV8100/SV8300 After installing the battery pack in the handset, charge the handset at least three to five hours before plugging it into the telephone line. Connect the telephone line cord to the TEL LINE jack and the other end to the AP(R)-L Unit.
Page 517 Select a location to avoid excessive heat or humidity. The base unit should be placed on a desk or tabletop near a standard 120 Vac outlet and within reach of the telephone line connection on the UNIVERGE SV8100/SV8300 Multiline Terminal. Keep the base unit and the handset away from sources of electrical noise (e.g.
Page 518: Figure 8-5 Connecting The Base Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Use caution when installing or modifying telephone lines. term To connect the D Cordless Terminal to the host telephone: Unplug the telephone line cord from the host telephone, and connect it to the LINE IN jack.
Page 519 UNIVERGE SV8100/SV8300 Issue 1.0 term ® II T (DTH-4R-1) ORDLESS ERMINAL ECTION This cordless terminal achieves a maximum range of 50~150 feet for transmitting and receiving in accordance with the highest specifications set by the FCC and IC Part 15.
Page 520: Figure 8-6 D Term Cordless Lite Ii Controls And Indicators
Issue 1.0 UNIVERGE SV8100/SV8300 Headset Jack Conference (CONF) Key LCD Message Display 10. Transfer (TRANSFER) Hold (HOLD) Key Channel (CH) Key Talk (TALK) Key 12. Redial (REDIAL) or Desk/Cordless Softkey Switch Key Numeric Keypad 13. F3 14. F4 15. Ringer/Volume (Ring/Vol) Microphone 16.
Page 521 UNIVERGE SV8100/SV8300 Issue 1.0 21 22 23 17. Line Out 21. Power 18. Line In 22. Desk LED 19. Cordless 23. Desk 20. Cordless LED term Figure 6-62 D Cordless Lite II Controls and Indicators (Continued) System Hardware Manual 8 - 9...
Page 522: Installation Precautions
Connect the cord from the telephone jack to the Base Unit LINE IN jack. Line in From Telephone Jack Figure 8-7 Connecting Base Unit to the Telephone Jack Connect a qualified NEC digital Multiline Terminal to the LINE OUT jack. 8 - 10 Installing SV8100/SV8300 Cordless Telephones...
Page 523: Applying Power To The Charging Unit
UNIVERGE SV8100/SV8300 Issue 1.0 Line Out term Series E or Series i Multiline Terminal Figure 8-8 Connecting the Base Unit to the Multiline Terminal Applying Power to the Charging Unit The unique design of the telephone allows the user to place the handset in the charging unit with or without the belt clip attached.
Page 524: Standard Wall Plate Mounting
Issue 1.0 UNIVERGE SV8100/SV8300 The AC adapter furnished with this telephone may be equipped with a polarized line plug (one blade is wider than the other). This plug fits in the power outlet only one way. Refer to Figure 8-10 Polarized Plug.
Page 525: Figure 8-11 Attaching The Wall Mount Stand To The Base Unit
Figure 8-12 Placing the AC Adapter Cord In the Wall Mount Stand Plug one end of the short telephone cord (locally supplied) in the LINE IN jack on the base unit. Plug one end of the NEC digital multiline telephone in the LINE OUT jack. Place the telephone cords inside the molded channels on the bottom of the wall mount stand.
Page 526: Figure 8-13 Placing The Base Unit On The Posts Of The Wall Plate
Issue 1.0 UNIVERGE SV8100/SV8300 Plug the other end of the short telephone cord in the modular wall jack in the center of the wall plate. Place the base unit on the posts of the wall plate and push down until it is firmly seated.
Page 527: Direct Wall Mounting
UNIVERGE SV8100/SV8300 Issue 1.0 Direct Wall Mounting When a standard wall plate is not available, mount the telephone directly on the wall. Before mounting the telephone, consider the following: Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.
Page 528: Figure 8-16 Placing The Telephone Cords In The Wall Mount Stand
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 8-16 Placing the Telephone Cords in the Wall Mount Stand Place the base unit on the posts of the wall screws and push down until it is firmly seated. Figure 8-17 Attaching the Wall Mount Unit to the Wall Plug the other end of the short telephone cord in a telephone wall jack.
Page 529: Charging Unit Wall Mounting
UNIVERGE SV8100/SV8300 Issue 1.0 Charging Unit Wall Mounting The charging unit can be wall mounted. Before installing, consider the following: Select a location away from electrical cables, pipes, or items behind the mounting location that could cause a hazard when inserting screws.
Page 530: Attaching And Removing The Belt Clip
Issue 1.0 UNIVERGE SV8100/SV8300 Plug the AC adapter in a standard 120 Vac wall outlet. Attaching and Removing the Belt Clip A belt clip can be used to attach the handset to a belt or pocket for convenient portability. Slide the clip in the tab slots. Press firmly until it snaps into place. The belt clip fits snugly on the handset.
Page 531: Figure 8-22 Removing The Battery Cover
UNIVERGE SV8100/SV8300 Issue 1.0 4.10 Installing the Handset Battery Pack Before installing batteries, refer to Regulatory on page R-1. Follow safety regulations when handling batteries. To remove the battery cover, press the latch and slide the cover down and off the handset.
Page 532: Charging The Handset Battery Pack
Issue 1.0 UNIVERGE SV8100/SV8300 Replace the cover and slide it forward until it latches. Figure 8-24 Replacing the Battery Cover 4.11 Charging the Handset Battery Pack term The rechargeable battery pack must be fully charged before using the D Cordless Lite II handset for the first time.
Page 533: Standby Mode
UNIVERGE SV8100/SV8300 Issue 1.0 4.14 Standby Mode The handset display turns on the battery low icon. All LEDs are turned off and LCD messages are cleared. A battery low alert tone is emitted every 15 seconds and lasts for three minutes.
Page 534: Cleaning The Battery Charge Contacts
Issue 1.0 UNIVERGE SV8100/SV8300 4.16 Cleaning the Battery Charge Contacts To maintain a good charge, clean all charging contacts on the handset and charging unit about once a month. Use a pencil eraser or other contact cleaner. Do not use liquids or solvents.
Page 535: D Analog Cordless Ii (Dtr-1R-2)
NALOG ORDLESS ECTION term The UNIVERGE SV8100/SV8300 supports the D Analog Cordless II telephone. The DTR-1R-2 is a 5.8Ghz digitally expandable cordless telephone that places a fully featured cordless handset anywhere in your home or office where AC power is available to connect the handset chargers.
Page 536: Installing The Rechargeable Battery Pack Into The Handset
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 8-27 Opening the DTR-1R-2 Battery Cover Installing the Rechargeable Battery Pack into the Handset The handset is powered by a rechargeable battery pack. The battery recharges automatically when the handset is placed in the base unit. To...
Page 537: Figure 8-29 Install The Battery
UNIVERGE SV8100/SV8300 Issue 1.0 Turn the battery pack so that the connector with the red and black wires is near the jack inside the battery compartment. Match the connector's wire colors to the polarity label in the battery compartment (the connector notches fit into the grooves of the jack only one way).
Page 538: Connecting The Base Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Use only the NEC rechargeable battery pack supplied with your cordless telephone. Replacement battery packs are also available. Contact your NEC Representative. Connecting the Base Unit Connect the AC adapter to the DC IN 9V jack and to a standard 120V AC wall outlet.
Page 539: Mount The Base Unit On A Standard Wall Plate
Figure 8-31 Connect the Base Unit on page 8-26. If your telephone outlet is not modular, contact your NEC Representative for assistance. Mount the Base Unit on a Standard Wall Plate This telephone can be mounted on any standard wall plate.
Page 540: Mount The Base Unit On A Direct Wall Mounting
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 8-32 Install the Wall Mount Adapter on page 8-27. Plug the AC adapter into a standard 120V AC wall outlet. Hook the cord on the notch of the wall mount adapter. Refer to Figure 8-32 Install the Wall Mount Adapter on page 8-27.
Page 541: Connecting The Charger
UNIVERGE SV8100/SV8300 Issue 1.0 Make sure the wall material is capable of supporting the weight of the base and handset. Use #10 screws (minimum length of 1 & 3/8 inches) with anchoring devices suitable for the wall material where the base unit will be placed.
Page 542 ® DECT (DTL-8R-1) ORDLESS ECTION DTL-8R-1 is a cordless telephone that is adapted for digital NEC PBX (Private Branch Exchange. It is designed for use in the office environment. term ® Figure 8-36 D Cordless DECT (DTL-8R-1) A Handset and wired phone cannot be used at the same time.
Page 543: Figure 8-37 System Overview
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 8-37 System Overview Selecting a Location term Select a location for the D Cordless DECT to avoid excessive heat or term humidity. The base unit of the D Cordless DECT can be placed on a desk or tabletop near a standard 120 Vac outlet and telephone line jack.
Page 544: D Cordless Dect (Dtl-8R-1)
Connect the cord from the telephone jack to the Line In on the D Cordless DECT. Figure 8-38 Connecting Telephone Cords to the Telephone Jack term Connect a qualified NEC digital Multiline Terminal to the D Cordless DECT. 8 - 32...
Page 545: Figure 8-40 Applying Power To The Charging Unit
UNIVERGE SV8100/SV8300 Issue 1.0 Line "OUT" To DTH, DTR and DTL Multiline Telephones term Figure 8-39 Connecting the D Cordless DECT to the Multiline Terminal Applying Power to the Charging Unit The unique design of the telephone allows the user to place the handset in the charging unit with or without the belt clip attached.
Page 546: Figure 8-41 Polarized Plug
Issue 1.0 UNIVERGE SV8100/SV8300 Use only the supplied AC adapter for the charging unit. The AC adapter furnished with this telephone may be equipped with a polarized line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way.
Page 547: Figure 8-42 Attaching The Wall Mount Stand To The Base Unit
Figure 8-43 Placing the AC Adapter Cord Inside the Wall Mount Stand Plug one end of the short telephone cord (locally supplied) in the LINE jack on the base unit. Plug one end of the NEC digital multiline telephone into the PHONE jack. Place the telephone cords inside the molded channels on the bottom of the wall mount stand.
Page 548: Figure 8-44 Placing The Base Unit On The Posts Of The Wall Plate
Issue 1.0 UNIVERGE SV8100/SV8300 Plug the other end of the short telephone cord into the modular wall jack in the center of the wall plate. Place the base unit on the posts of the wall plate and push down until it is firmly seated.
Page 549: Figure 8-46 Inserting Screws Into The Wall For Wall Mounting The Telephone
Plug the AC adapter into the base unit. Plug one end of the short telephone cord into the LINE jack on the base unit. Then plug one end of an NEC multiline telephone into the PHONE jack. Place the telephone cords inside the molded channels on the bottom of the wall mount stand.
Page 550: Figure 8-47 Placing The Telephone Cords Inside The Wall Mount Stand
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 8-47 Placing the Telephone Cords Inside the Wall Mount Stand Place the base unit on the posts of the wall screws and push down until it is firmly seated. Figure 8-48 Attaching the Wall Mount Unit to the Wall Plug the other end of the short telephone cord into a telephone wall jack.
Page 551: Figure 8-49 Inserting Screws For Wall Mounting
UNIVERGE SV8100/SV8300 Issue 1.0 Wall Mounting the Charging Unit The charging unit is also designed to be wall mounted. Before mounting the charging unit, consider the following: Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.
Page 552: Figure 8-51 Placing The Charging Unit On The Wall
Issue 1.0 UNIVERGE SV8100/SV8300 Place the charging unit on the posts of the wall screws and push down until it is firmly seated. Figure 8-51 Placing the Charging Unit on the Wall Plug the AC adapter into a standard 120 Vac wall outlet. Refer to...
Page 553: Term ® Cordless Dect (Dtl-8R-1)
UNIVERGE SV8100/SV8300 Issue 1.0 To remove the clip, press the retaining clip in toward the belt clip blade and slide the clip up at the same time. Figure 8-53 Removing the Belt Clip Installing the Handset Battery Pack term ®...
Page 554: Figure 8-55 Replacing The Battery Pack
Issue 1.0 UNIVERGE SV8100/SV8300 Slide the battery pack down into the handset. It may be necessary to remove the old battery at this time. Figure 8-55 Replacing the Battery Pack Replace the cover and slide it up until it latches onto the handset.
Page 555: Figure 8-57 D Term ® Cordless Repeater Dtl-Rpt-1
UNIVERGE SV8100/SV8300 Issue 1.0 term ® DTL-RPT-1 ORDLESS EPEATER ECTION The UDR100 repeater lets you extend the coverage area of your cordless DECT telephone system in all directions. term ® Figure 8-57 D Cordless Repeater DTL-RPT-1 System Hardware Manual 8 - 43...
Page 556: Figure 8-58 Single Repeater Attached To Base
Issue 1.0 UNIVERGE SV8100/SV8300 If the repeaters are installed so their coverage area overlaps the coverage area of the base, the base can hand-off calls to the repeaters as the user moves from one coverage area to another. When it's connected to the repeater, the mobile handset...
Page 557: Figure 8-59 Six Repeaters Attached To Base
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 8-59 Six Repeaters Attached to Base In addition, the UDR100 supports a sequential or "daisy chain" layout to extend coverage in a single direction. Up to three repeaters can be installed in sequence: Figure 8-60 Daisy-Chain Layout For detailed information on daisy-chain layout and configuration, contact your installer or refer to the UDR100 Administrator's Guide.
Page 558 Issue 1.0 UNIVERGE SV8100/SV8300 Setting Up Your Repeater Before installing the repeater, you need to activate the repeater mode on your base and then register the repeater to the base and any handsets. Before you start the registration process, be sure you have:...
Page 559 UNIVERGE SV8100/SV8300 Issue 1.0 7.1.3 Manual Registration If you are registering more than one repeater to the same base, you must use the manual registration procedure. Connect the repeater to power for 1~5 seconds and then disconnect it. Reconnect the power to the repeater. The LED on the repeater flashes slowly, indicating the repeater is in registration mode.
Page 560 Issue 1.0 UNIVERGE SV8100/SV8300 7.1.4 Registration for a Daisy-Chain Layout Registering the repeaters to operate in a daisy-chain or sequential layout requires network administrator access and configuration software. Contact your installer or refer to the DTL-RPT-1 Administrator's Guide (provided with the configuration software) for more information.
Page 561: Figure 8-61 Base Coverage Area
UNIVERGE SV8100/SV8300 Issue 1.0 7.2.2 Map the Base Coverage Area To find the best location for the repeater, you need to determine the base coverage area. Stand near the base and make a call. Walk away from the base with the handset, and make a note where the signal becomes weaker.
Page 562: Figure 8-62 Incorrect Installation
Issue 1.0 UNIVERGE SV8100/SV8300 7.2.4 Installing the Repeater Be sure the wall material can hold the weight of the repeater. Never install a repeater in damaged or decaying wall material. Hold the repeater in its final location, and mark the center of the top edge.
Page 563: Figure 8-63 Base Coverage Area
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 8-62 Incorrect Installation 7.2.5.2 Correct Installation Figure 8-63 Base Coverage Area illustrates repeaters that have been correctly installed. Figure 8-63 Base Coverage Area System Hardware Manual 8 - 51...
Page 564: Figure 8-64 Daisy-Chain Layout
Issue 1.0 UNIVERGE SV8100/SV8300 7.2.5.3 Daisy-Chain Installation You can combine "normal" and "daisy-chain" connections to create a wide variety of coverage configurations, as long as you have no more than six repeaters per base unit. Figure 8-64 Daisy-Chain Layout Troubleshooting Chart term ®...
Page 565: Figure 8-65 D Term Usb Wireless Headset (Cs50-Usb)
UNIVERGE SV8100/SV8300 Issue 1.0 PTIONAL EADSETS ECTION term ® USB Wireless Headset This headset supports WebDial 2.1.4.0 or higher, Softphone 310 and SP30 Softphone version 9 or higher with digital encryption, TIA810a compliance, and a noise-canceling microphone for secure, clear, and quiet conversations.
Page 566 Issue 1.0 UNIVERGE SV8100/SV8300 8.1.3 Charging the Headset Battery To charge the headset battery, place it in the docking cradle. During charging, the charge indicator is On. When charging is complete the indicator goes Off. The headset must be charged for a minimum of one hour before use –...
Page 567 UNIVERGE SV8100/SV8300 Issue 1.0 term ® Headset Cordless II Terminal The DTR-1C-2 (CS50 Wireless Office Headset System) combines ultimate mobility with excellent sound quality for hands-free conversation. Refer to term Figure 8-66 D Headset Cordless Listening Volume/Mute Headset Charge Cradle...
Page 568 Issue 1.0 UNIVERGE SV8100/SV8300 8.2.1 Connecting the Switch Connection requires installing an AP(R)-L analog adapter (not supplied with this unit) on the multiline terminal. Connect the AC power adapter to the AC Power Adapter Jack (indicated by a 9V icon) on the bottom of the Base, and plug the adapter into a power source.
Page 569 UNIVERGE SV8100/SV8300 Issue 1.0 Locate the configuration Dial, and rotate it to another of the four positions until a dial tone is heard. Align the number with the seam line on the right side. 8.2.4 Adjusting the Volume Listening Volume Adjust listening volume using Listening Volume/Mute control on the headset speaker end.
Page 570 Issue 1.0 UNIVERGE SV8100/SV8300 Switch from Handset to Headset When you are using the handset during a call and want to switch to the headset: Press the headset Talk Button, and the headset can be used. Place the telephone handset on the Multiline Terminal.
Page 571: Figure 8-67 Cordless Headset (Mx250)
8.3.2 NEC D Cordless Phone Headset (M175) The NEC M175 mobile headset offers hands-free convenience anywhere you go. Its convertible design can be worn with a headband or earloop on either ear, depending on whether you want greater stability or convenient small size. The pivoting noise- canceling microphone keeps your voice crystal clear, even in noisy environments.
Page 572: Figure 8-69 Nec Polaris Supraplus
Supra Series Monaural or Binaural headsets are super stable and perfect for phone-intensive jobs. They have an adjustable headband so they can be worn all day. The Binaural model allows you to hear conversations in extra noisy environments. Figure 8-69 NEC Polaris Supraplus term ® ® 8.3.4...
Page 573: Figure 8-71 Nec Polaris Tristar
TriStar headset is the best solution. It’s three point design ensures that it is comfortable and stable on the ear. It is very lightweight and can also fit most eyeglass wearers. Figure 8-71 NEC Polaris TriStar term ® ® 8.3.6...
Page 574 Due to the environment where the telephones or headsets are located, ambient noise may affect performance. Please contact NEC for the recommended headset to use with VoIP applications. 8 - 62...
Page 575 ECTION The implementation of SIP Digital Enhanced Cordless Telecommunication (DECT) in a NEC Telephone System is a stand-alone DECT system that is connected to the NEC Telephone System via a TCP/IP connection using Session Initiation Protocol (SIP). This means that in the NEC Telephone System, the DECT extensions must be assigned as SIP extensions.
Page 576: Figure 9-1 Sip Dect System Configuration
Refer to NEC SIP DECT Solutions Technician’s Guide, DAP Planning as a guideline. Read the sections DAP Cabling and DAP Power Provision in the NEC SIP DECT Solutions Technician Guide carefully to determine how the DAPs should be powered and how the cable must be run.
Page 577 Check that the lamp on the IP Switch indicates that the connection is established. (For UNIVERGE SV8100 only) Connect a network cable between the CD-(X)ILPA and the IP Switch. The next step is setting up your IP Addressing structure. Refer to the NEC SIP DECT Solutions Technician’s Guide, IP Addressing.
Page 578 Issue 1.0 UNIVERGE SV8100/SV8300 - - NOTES - - 9 - 4 Installing SV8100/SV8300 Wireless Telephones...
Page 579 Conferencing solutions provide premium, full-duplex audio to small Chapter conference rooms as a single unit or to larger rooms when expanded by up to three units that also expand microphone access and loudspeaker coverage. NEC C ™ ONFERENCE ECTION Description...
Page 580: Figure 10-1 Nec Conference Max
Issue 1.0 UNIVERGE SV8100/SV8300 ™ Figure 10-1 NEC Conference Max Installation Connect the provided 25 foot Cat. 5 cable between the LINK OUT jack of the base unit and the LINK IN jack of the conferencing pod. Connect the provided RJ-11 cable between the base unit and the telephone jack.
Page 581: Table 10-1 Keypad Functions
UNIVERGE SV8100/SV8300 Issue 1.0 Keypad Functions Refer to Table 10-1 Keypad Functions. Table 10-1 Keypad Functions Function ON/OFF key Press to activate the telephone and access dial tone. (telephone icon) Press again to hang up and return to standby mode.
Page 582 Issue 1.0 UNIVERGE SV8100/SV8300 Table 10-2 Programming Options (Continued) Menu Option Programming Flash Press REDIAL. The current duration flashes. Press 1~5 Duration to select duration as follows: 1 = 600 ms 2 = 300 ms 3 = 150 ms 4 = 100 ms 5 = 80 ms Press REDIAL to save the selection.
Page 583: Figure 10-2 Nec Conference Max Plus
(7.2 Volts, 2200 mAh) that allows 12 hours of continuous talk time. A Base Unit that is connected to a power source and analog telephone service is required for operation of the conferencing pods. Figure 10-2 NEC Conference Max Plus System Hardware Manual 10 - 5...
Page 584: Table 10-3 Keypad Functions
Issue 1.0 UNIVERGE SV8100/SV8300 Installing the Base Unit To install the base unit: Connect the provided RJ-11 cable between the Base Unit and the telephone jack. Connect the power cord to the Base Unit and plug it in an electrical outlet.
Page 585: Table 10-4 Programming Options
UNIVERGE SV8100/SV8300 Issue 1.0 Table 10-3 Keypad Functions (Continued) Function CLEAR (vertical line Press to clear the last digit entered or press and hold to and left arrow icon) clear all numbers. Press to exit programming mode. VOLUME (loud and...
Page 586 ONFERENCE ECTION The NEC SIP Conference Max expandable conferencing telephone provides premium, full-duplex audio to small conference rooms as a single unit and to larger rooms as an expanded system. Up to four SIP Conference Max units can be linked, expanding not only microphone coverage but loudspeaker coverage and control access as well.
Page 587: Figure 10-3 Nec Sip Conference Installation
Link Out jack on the first phone and to the Link In jack on the second phone. Up to three additional SIP Conference Max phones for a total of four may be connected. Figure 10-4 Install Additional NEC SIP Conference Units System Hardware Manual 10 - 9...
Page 588: Table 10-5 Keypad Functions
Issue 1.0 UNIVERGE SV8100/SV8300 Connecting and Charging the Batteries To connect and charge the batteries: Slide the cover off the battery compartment on the bottom of one pod. Connect the battery pack plug in the port in the compartment and install the battery pack.
Page 589: Table 10-6 Programming Options
UNIVERGE SV8100/SV8300 Issue 1.0 Programming Options To enter Programming mode, press and hold REDIAL until a diamond arrow is displayed on the LCD. Then press the applicable key and follow the instruction Table 10-4 Programming Options. Table 10-6 Programming Options...
Page 590 Issue 1.0 UNIVERGE SV8100/SV8300 Compliance This product is in compliance with the following regulations and requirements: FCC Part 15/ICES-003 This product has been tested and complies with the limits for a Class A digital device. FCC Part 68 US:FBIMT01B910158015 Ringer Equivalence Number (REN):0.1B(ac) Industry of Canada (IC) IC: 1970A-158015: REN:0.1B(ac)
Page 591 Installing SV8100/SV8300 Optional Equipment ENERAL NFORMATION ECTION This chapter provides information for installing optional equipment, such as Chapter term PGD(2)-U10 ADPs, background music, door boxes, DSS consoles, D VSR, external paging as well as other handsets, recording devices and adapters on the SV8100/SV8300 digital and IP telephones. PGD(2)-U10 ADP ECTION Using a PGD(2)-U10 ADP...
Page 592: Figure 11-1 Pgd(2)-U10 Adp
Issue 1.0 UNIVERGE SV8100/SV8300 The PGD(2)-U10 ADP connects to any available digital extension port. The terminal connections made within the PGD(2)-U10 ADP and the jumper settings determine what features are used for each circuit. Channel 2 Channel 1 Status LED...
Page 593: Figure 11-2 Remove Cover From Pgd(2)-U10 Adp
UNIVERGE SV8100/SV8300 Issue 1.0 Remove the screw from the front of the PGD(2)-U10 ADP. Figure 11-2 Remove Cover from PGD(2)-U10 ADP Using a screwdriver, break out the plastic piece covering the cable hole. Figure 11-3 Remove Plastic Cover from Cable Hole Set the S3 –...
Page 594: Figure 11-4 Pgd(2)-U10 Adp Jumper Settings
Issue 1.0 UNIVERGE SV8100/SV8300 Table 11-2 PGD(2)-U10 ADP S3 – S6 Jumper Settings Function LED Indication Open Open Door Box On when in use. Open Short External Paging Speaker On when in use. Channel 1 Short Open External Ringer On when in use.
Page 595 UNIVERGE SV8100/SV8300 Issue 1.0 Strip one end of the cable to be connected to the control relay or door box so that approximately 1/4” (8 mm) of bare wire is exposed. Insert the cable into the proper CN4 or CN5 location while holding down the lock button (holding down this lock button is easiest with a flat-head screwdriver).
Page 596: Figure 11-5 Pgd(2)-U10 Adp Connection Diagram
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 11-5 PGD(2)-U10 ADP Connection Diagram 11 - 6 Installing SV8100/SV8300 Optional Equipment...
Page 597: Figure 11-6 Connecting Cable To The Pgd(2)-U10 Adp
UNIVERGE SV8100/SV8300 Issue 1.0 Flat-head screwdriver Cable Press down CN4, CN5 Figure 11-6 Connecting Cable to the PGD(2)-U10 ADP Repeat Steps 4 and 5 for any additional connections required. Replace the cover and tighten the screw to hold the cover in place.
Page 598: Figure 11-7 Pgd(2)-U10 Adp Connections
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 11-7 PGD(2)-U10 ADP Connections Install a modular jack for each PGD(2)-U10 ADP. For each module, run one-pair 24 AWG station cable from the cross-connect block to a modular jack. Ground the unused pair. Terminate the extension leads to GRN/RED of the modular jack.
Page 599: Figure 11-8 Installing The Screws
UNIVERGE SV8100/SV8300 Issue 1.0 In some cases, when testing the operation of an extension port when connecting to a Cordless II, Cordless Lite II, or PGD(2)-U10 ADP, a technician may connect a line cord directly from an extension port on the CD-8DLCA/CD-16DLCA Blade. Though this is not the recommended connection, it can be used to test these devices.
Page 600: Figure 11-9 Wall Mounting The Pgd(2)-U10 Adp
Issue 1.0 UNIVERGE SV8100/SV8300 The back of the PGD(2)-U10 ADP has two key-hole type openings. Place the PGD(2)-U10 ADP over the two screws and slide it down or over (depending on the positioning) to lock it in place. Figure 11-9 Wall Mounting the PGD(2)-U10 ADP...
Page 601: Figure 11-10 Cpru Connections
UNIVERGE SV8100/SV8300 Issue 1.0 Install bridging clips as required. Figure 11-10 CPRU Connections ECTION Installing a Door Box A PGD(2)-U10 ADP is required for this option. The Door Box is a self-contained, water-resistant, Intercom unit typically used to monitor an entrance door. A visitor at the door can press the Door Box call button (like a door bell).
Page 602 Issue 1.0 UNIVERGE SV8100/SV8300 Make sure the jumper in the PGD(2)-U10 ADP for the associated Door Box is set correctly. (Refer to Figure 11-4 PGD(2)-U10 ADP Jumper on page 11-4). Settings If a line cord was not previously connected to the PGD(2)-U10 ADP, complete Steps 3-6.
Page 603: Figure 11-11 Setting The Pgd(2)-U10 Adp For A Door Box
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 11-11 Setting the PGD(2)-U10 ADP for a Door Box System Hardware Manual 11 - 13...
Page 604: Figure 11-12 Installing A Door Box
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 11-12 Installing a Door Box 11 - 14 Installing SV8100/SV8300 Optional Equipment...
Page 605 UNIVERGE SV8100/SV8300 Issue 1.0 XTERNAL AGING ECTION External Page Two external page zone/door box circuits are provided by each PGD(2)-U10 ADP installed. Each Door Box/external page circuit provides a dry relay contact. The CD-CP00-US also provides a connection for external paging and a relay.
Page 606: Figure 11-13 Pgd(2)-U10 Adp Cable Connection
Issue 1.0 UNIVERGE SV8100/SV8300 Terminate the extension leads to GRN/RED of the modular jack. Terminate the unused leads to the jack. Install bridging clips as required. Plug a modular line cord from the mod jack to the CN1 connector on the PGD(2)-U10 ADP.
Page 607 UNIVERGE SV8100/SV8300 Issue 1.0 The PGD(2)-U10 ADP provides amplifiers for each page output port (for a maximum of +8 dBM, 600 ohms at 1KHz). No additional page amplification is provided by the PGD(2)-U10 ADP but, if required, an external page amplifier can be used for additional amplification.
Page 608 Issue 1.0 UNIVERGE SV8100/SV8300 Door Box /External Page Relay Contacts 6.2.1 Connecting a Contact Relay Device to a Door Box/External Page Relay To connect a dry contact relay device to a Door Box/External Page Relay: To connect to the CD-CP00-US:...
Page 609: Figure 11-14 Cd-Cp00-Us Page Connections
UNIVERGE SV8100/SV8300 Issue 1.0 The relay closes when the Door Box/external page zone is called. The maximum applied voltage is 24vDC at .5A for each contact. Figure 11-14 CD-CP00-US Page Connections XTERNAL ECORDING YSTEM XTERNAL INGER ECTION External Recording System or External Ringer The PGD(2)-U10 ADP allows the connection of an external recording system or external ringer.
Page 610 Issue 1.0 UNIVERGE SV8100/SV8300 Installing an External Recording System or External Ringer To connect to the PGD(2)-U10 ADP: Make sure the jumper in the PGD(2)-U10 ADP for the channel is set correctly. (Refer to Figure 11-4 PGD(2)-U10 ADP Jumper Settings page 11-4).
Page 611: Figure 11-15 Pgd(2)-U10 Adp Cable Connection
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 11-15 PGD(2)-U10 ADP Cable Connection Programming 10-03-01 : ETU Setup – Terminal Type (Circuit 1) 10-03-06 : ETU Setup – Terminal Type (Circuit 2) Confirm that the PGD(2)-U10 ADP has defined the circuit type as either type 7 for External Ringer or 9 for ACIs.
Page 612 Issue 1.0 UNIVERGE SV8100/SV8300 11-08-01 : ACI Group Pilot Number Assign pilot numbers to ACI groups. When a user dials the pilot number, they reach an available ACI software port within the group. Aspire S: ACI Groups 1-4 Aspire: ACI Groups 1-16...
Page 613 UNIVERGE SV8100/SV8300 Issue 1.0 15-12-01 : Conversation Recording Destination for Extensions - ACI Recording Destination Extension Number Use this option to assign the ACI Call Recording destination on a per extension basis. The destination can be an ACI port’s extension number (assigned in Program 11-06) or an ACI Department Group pilot number (assigned in Program 11-08).
Page 614 Issue 1.0 UNIVERGE SV8100/SV8300 USIC OURCES ECTION Music on Hold The system can provide Music on Hold from either an internally synthesized source on the CD-CP00-US or from an external source. The external MOH can be a tuner, tape deck, CD player, etc. The settings in Program 10-04-01 and 14-08-01 determine whether the source for MOH is internal or external.
Page 615: Figure 11-16 Cpru Connections
UNIVERGE SV8100/SV8300 Issue 1.0 Install a modular jack for each PGD(2)-U10 ADP. For each module, run one-pair 24 AWG station cable from the cross-connect block to a modular jack. Ground the unused pair. Terminate the extension leads to GRN/RED of the modular jack.
Page 616: Figure 11-17 Pgd(2)-U10 Adp Connections
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 11-17 PGD(2)-U10 ADP Connections 11 - 26 Installing SV8100/SV8300 Optional Equipment...
Page 617 UNIVERGE SV8100/SV8300 Issue 1.0 IGHT ELECTION ECTION Night Mode Selector Switch The Night Mode Switch relay closes when the system detects either an open or closure on the MISC block NIGHT SW terminals. Maximum 48v DC is output to the switch when open, and 7mA DC when shorted.
Page 618: Figure 11-18 Removing The Faceplate
Issue 1.0 UNIVERGE SV8100/SV8300 10.1.1 Removing the Faceplate Use the small notch at the lower right corner of the telephone, to lift the faceplate up. Each corner has a plastic locking pin which releases as the faceplate is lifted up.
Page 619: Figure 11-19 D Term Voice Security Recorder
The D Voice Security Recorder is a USB device that taps across the digital extension pair of the NEC telephone system allowing digital recording of the telephone user’s conversation. The file created is saved either to the local PC or to a network location, depending on the application blade. This adapter is for use with digital multiline terminals.
Page 620: Figure 11-20 Vsr Connection Configuration
Run the Setup.exe program file from the NEC installation CD BEFORE connecting the telephone interface unit to the PC. Using the USB cable provided, connect the USB interface of the NEC VSR unit to an available USB port on the PC.
Page 621 D VSR unit. term Connect the NEC telephone system to the remaining port on the D VSR unit. You are now ready to record. For Windows 2000 or XP term Using the USB cable provided, connect the USB interface on the D VSR unit to your PC.
Page 622: Figure 11-21 Voice Security Recorder Installation-1
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 11-21 Voice Security Recorder Installation-1 11 - 32 Installing SV8100/SV8300 Optional Equipment...
Page 623: Figure 11-22 Voice Security Recorder Installation-2
UNIVERGE SV8100/SV8300 Issue 1.0 Insert the NEC Installation CD in your CD drive and press Next>. Figure 11-22 Voice Security Recorder Installation-2 If you downloaded the files from the internet, uncheck the "Search removable media box", select the "Include this location…" box and enter the location where you stored the downloaded files (e.g.
Page 624: Figure 11-23 Voice Security Recorder Installation-3
Run SBladep.exe on your NEC Installation CD to install the D Voice Security Recorder application software on your PC. Using the USB cable provided, connect the USB interface of the NEC VSR unit to an available USB port on your PC.
Page 625: Figure 11-24 Vsr User Interface Tab Options
UNIVERGE SV8100/SV8300 Issue 1.0 The VSR application supports Microsoft Operating Systems that support USB devices. The following systems meet this requirement: WIN 98SE WIN Millennium Edition (ME) WIN 2000 WIN XP (all variants) VSR does not support WIN 95 and below, or WIN NT.
Page 626: Figure 11-25 Vsr Playback Tab
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 11-25 VSR Playback Tab Figure 11-26 Caller ID or Comment Editor 11 - 36 Installing SV8100/SV8300 Optional Equipment...
Page 627 Caller ID and number dialed are not available on the first release. Check with NEC for release date. The user can list recordings in order of importance (using exclamation mark) with Caller ID, Time + Date, or duration.
Page 628: Figure 11-27 View Levels And Control Recording
Issue 1.0 UNIVERGE SV8100/SV8300 11.3.4 VSR Record Tab This tab allows the user to view recording levels and control the recording. Figure 11-27 View Levels and Control Recording The Oscilloscope shows the local and remote levels on the line separately (Microphone is the user level, and speaker is the distant party level).
Page 629: Figure 11-28 Vsr About Tab
UNIVERGE SV8100/SV8300 Issue 1.0 11.3.5 About Tab This tab provides version and manufacturer information. Figure 11-28 VSR About Tab System Hardware Manual 11 - 39...
Page 630: Figure 11-29 Select Vsr Setup Options
Issue 1.0 UNIVERGE SV8100/SV8300 11.3.6 Options Tab This tab allows the user to select various setup options of the VSR. Figure 11-29 Select VSR Setup Options Automatically start recording every call Starts the recording when a call, including an internal extension call, is made.
Page 631: Figure 11-30 Manage Calls At Completion
UNIVERGE SV8100/SV8300 Issue 1.0 Call Selection Saves all calls or only those that exceed an established limit. Show splash screen at startup When selected, the VSR logo is shown for five seconds when the application is started. Email format Allows the user to select the type of file inserted in an e-mail...
Page 632: Figure 11-31 File Management Tab
Issue 1.0 UNIVERGE SV8100/SV8300 11.3.7 File Management Tab File management is necessary when the user makes many telephone calls and stores each conversation. The selections are self-explanatory. Figure 11-31 File Management Tab 11 - 42 Installing SV8100/SV8300 Optional Equipment...
Page 633: Figure 11-32 Comvurgent Options For Additional Adjustments
This special configuration program can only be accessed by browsing to the installation location (default C:\Program term Files\Comvurgent\XtRecorder), and then click on the NEC D Config.exe. The customer takes all responsibility to ensure they meet legal requirements. Comvurgent provides the user option settings to meet customer demands and cannot be responsible for misapplication of the product.
Page 634: Figure 11-33 Customizing Application To Meet Requirements
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 11-33 Customizing Application to Meet Requirements Display splash screen at the start of every call Reminds user that recording is taking place by splashing a screen with every call. term Show D Recorder dialog at the start of every call Displays application record screen anytime a call is being recorded.
Page 635: Figure 11-34 Voice Security Recorder Connection
UNIVERGE SV8100/SV8300 Issue 1.0 Password Locks access to these settings and those at the user level. When making changes, the application must be closed and started again to become effective. Figure 11-34 Voice Security Recorder Connection 11.4 Operation Note term ®...
Page 636 Call Logging Unit Connection Configuration. 11.5.3 Connectors The NEC 4-Port Digital Call Logging Unit USB recording device has five connectors and four LED indicators: One PC USB connector, from which the device derives its power and streams all speech and control channel information up to the host PC and NEC BackOffice application.
Page 637: Figure 11-35 4-Port Digital Call Logging Unit Connection Configuration
An available PCI slot for each USB Controller Card. LAN connection for remote access to stored calls. NEC BackOffice Recorder software. Calls should be stored on the same host PC. Using the GSM 6.10 Compression option, each 1Gb of Hard Disk storage allows recording of about 168 hours of calls.
Page 638 11.5.6.1 Location Preparation The wiring for the extensions should be within six feet of the PC location. For this reason, the PC for the NEC BackOffice Recorder should be located near the MDF for extension wiring. The installer will need to prepare the wiring to tap off the digital pair with a T-Connect type setup.
Page 639 USB cable and plug the USB cable into the PC. Windows will respond with the Found New Hardware wizard. Insert the provided NEC BackOffice CD into the CD drive of the PC. Direct the installation of the driver to Specific Location and specify the Driver folder on the CD.
Page 640: Figure 11-36 Digital Station Ports
Figure 11-36 Digital Station Ports 11.5.6.4 Install the 4-Port Digital Call Logging Unit BackOffice Software Insert the NEC BackOffice CD into the CD drive of the PC. Locate the Recorder folder. Click on the Setup.exe file in the Recorder folder.
Page 641: Figure 11-37 Recorder Screen
UNIVERGE SV8100/SV8300 Issue 1.0 A NEC BackOffice Recorder shortcut will now be displayed on the desktop. Click on the NEC BackOffice Recorder shortcut. The Recorder screen is displayed. See Figure 11-37 Recorder Screen. Figure 11-37 Recorder Screen Double click on the first line in the sequence to configure.
Page 642: Figure 11-38 Enter Line Details Dialog Box
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 11-38 Enter Line Details Dialog Box Name the device (user or extension name). Click on the Browse button to identify the storage location for the device. It is recommended that you create a “Master Calls”...
Page 643 File then Exit from the Recorder screen menu to save your configuration. The NEC Recorder will now record every call to and from the telephones. It is important to use proper procedure to shut down the application and PC when necessary.
Page 644: Figure 11-39 Recorder Screen
UNIVERGE SV8100/SV8300 Figure 11-39 Recorder Screen 11.5.6.5 Choose and Install Player Options There are several player options available with the NEC BackOffice Recording solution. Desktop Player – can be loaded on an individual user’s PC, giving the user complete access (although restrictions can be applied) to call management;...
Page 645 Desktop Player which is designed to be used by an individual user to term play back their own archive of calls or to play back NEC D VSR calls stored on their PC or network. It is designed to easily manage calls from one storage location.
Page 646: Figure 11-41 Vsr Manager Screen
UNIVERGE SV8100/SV8300 The second player option is the VSR Manager. Take your call recording environment to the next level with NEC’s VSR application software. VSR Manager provides advanced visibility, access, retrieval, and playback tools for the VSR Recorder administrators. It provides an intuitive interface for...
Page 647 Windows 2000 (recommended latest service pack) Windows 2003 Microsoft .Net Framework 1.1+ If your PC does not meet the above requirements, please contact NEC. VSR Manager 2.0 can be provided if upgrading to the minimum requirements is not possible or desirable 11.6.1.3...
Page 648 Issue 1.0 UNIVERGE SV8100/SV8300 11.6.1.4 Is the Microsoft .Net Framework 1.1 Installed? VSR Manager 2.0 requires the Microsoft .Net Framework, which should be installed on your PC prior to installing VSR Manager. If your Windows operating system has been kept up to date with Windows Service Packs, it’s likely the Microsoft .Net Framework 1.1 has already been...
Page 649 UNIVERGE SV8100/SV8300 Issue 1.0 The Application Security Key is associated with your Software license. The Application Security Key is non-transferable and will not be replaced if lost. If the key becomes damaged within the warranty period, you will need to return...
Page 650 Issue 1.0 UNIVERGE SV8100/SV8300 11.6.3.2 Register VSR Manager To get additional support, it’s a good idea to register your copy of VSR Manager. When you register, you can sign up for timely EMail notices about product updates so you can keep VSR Manager running at peak performance and benefit from any new features and enhancements.
Page 651: Figure 11-42 D Term Vsr Reporter Pro Screen
Desktop Player which is designed to be used by an individual user to term play back their own archive of calls or to play back NEC D VSR calls stored on their PC or network. It is designed to easily manage calls from one storage location.
Page 652: Figure 11-43 Vsr Reporter Pro Screen
Issue 1.0 UNIVERGE SV8100/SV8300 VSR Reporter Pro is designed to provide the manager or supervisor the ability to quickly and easily gain access to important calls. Figure 11-43 VSR Reporter Pro Screen These two players can be combined in any number of configurations within the company, providing control and management where needed and simple playback in other locations.
Page 653 Windows 2000 (recommended latest service pack) Windows 2003 Microsoft .Net Framework 1.1+ If your PC does not meet the above requirements, please contact NEC. VSR Reporter Pro 2.0 can be provided if upgrading to the minimum requirements is not possible or desirable 11.7.1.3...
Page 654 Issue 1.0 UNIVERGE SV8100/SV8300 If the Microsoft .Net Framework 1.1 is not installed, you can download it from the Microsoft web site. The link to Microsoft .Net Framework download at time of this writing:http://www.microsoft.com/downloads/ details.aspx?FamilyID=262d25e3-f589-4842-8157- 034d1e7cf3a3&displaylang=en Not sure if .Net is installed: If you have any doubts, try to install VSR Reporter Pro 2.0.
Page 655 UNIVERGE SV8100/SV8300 Issue 1.0 11.7.3 Install and Register VSR Reporter Pro 2.0 In a multi-user operating systems, such as Windows 2000 or Windows XP, applications are generally installed in a folder from which it can be run by all users, such as C:\Program Files. You can install or uninstall applications only if you have administrative privileges on your computer.
Page 656: Figure 11-44 Installing Adapters
The ILPA does the negotiation and detection with the switch and then relays the power to the IP terminal device. This provides an additional way to power the NEC IP terminals. With this adapter, the IP terminals on the UNIVERGE SV8100/SV8300 system can be powered using:...
Page 657: Figure 11-45 In-Line Power Adapter
UNIVERGE SV8100/SV8300 Issue 1.0 NEC power supply PoE-managed switch (BlueFire 200/24) (in-line and spare pair detection) Router Blade (spare pair detection) Cisco Data Switch – CDP supported (in-line and spare pair detection) In-Line Power Adapter Figure 11-45 In-Line Power Adapter 12.2.1...
Page 658: Figure 11-46 In-Line Power Adapter Switch Settings
SW1 Setting IEEE802.3af STD System Cisco Discovery Protocol System NEC BlueFire 200/24 Switch Set the switch setting on the NEC IPhone or IP adapter to the correct position. IPhone (SW2) or IP Adapter (SW1) SW Setting NEC Power Patch Panel...
Page 659: Figure 11-47 Nec Terminal Connection To An Ieee 802.3Af Poe Switch
UNIVERGE SV8100/SV8300 Issue 1.0 Connect the NEC VoIP telephone to the TEL connector on the ILPA-R adapter with the LAN cable provided with the adapter. If a customer-provided cable is used, the total length from the switch to the telephone should be less than 328 feet.
Page 660 Issue 1.0 UNIVERGE SV8100/SV8300 12.3 ADA-L UNIT Using the ADA-L UNIT (Ancillary Device Adapter) provides a recording jack connection from a telephone to an external tape recorder, speaker or PC. Both sides of the conversation are recorded. The adapter output is a 1/8”...
Page 661: Figure 11-48 Ada-L Unit
UNIVERGE SV8100/SV8300 Issue 1.0 12.3.1 ADA-L UNIT Switch Settings Figure 11-48 ADA-L UNIT shows the location of the switches. The dip switches (DSW) allow a technician to configure the unit for specific settings. Due to location, set switches prior to installation of ADA-L on DTL/ITL multiline terminal.
Page 662: Figure 11-49 Separate Tilt Leg From Leg Support
Issue 1.0 UNIVERGE SV8100/SV8300 Table 11-3 ADA-L Unit Switch Settings (Continued) Switch Description/Settings Output Hook Signal to External Device DSW 1 On = Output Off = No Output (Default) Record Confirmation Tone Switches DSW 2 On = Tone On (DSW)
Page 663: Figure 11-50 Bottom Option Interface Knockout
UNIVERGE SV8100/SV8300 Issue 1.0 Push the two stopper tabs through the slots to separate the tilt leg from the leg support. Lay the tilt leg and the leg support flat to expose ADA-L UNIT compartment. Carefully pry loose the knockout covering the bottom option...
Page 664: Figure 11-52 Ada-L Out Jack Connection
Issue 1.0 UNIVERGE SV8100/SV8300 12.3.3 ADA-L UNIT Connection The mini-plug connection cord should not use an attenuator and have a monaural (single ring) mini-plug connection for normal recording. 12.3.3.1 ADA-L UNIT Connection for Recording Only Set the ADA-L UNIT DSW switches (Refer to...
Page 665: Figure 11-53 Ada-L In Jack Connection
UNIVERGE SV8100/SV8300 Issue 1.0 12.3.3.2 ADA-L UNIT Connection for Sending Recorded Calls to the Telephone Set the ADA-L UNIT DSW switches (see Figure 11-48 ADA-L UNIT on page 11-71). Set DSW 6 to ON. When sending recorded calls to the telephone, set DSW switch 1 to ON.
Page 666: Figure 11-54 Apr-L Unit
Issue 1.0 UNIVERGE SV8100/SV8300 When installing or removing the adapters, the telephone should be unplugged from the system. The APR-L UNIT supports reverse-polarity, message waiting lamping, or Caller ID. 12.4.1 APR-L UNIT Switch Settings Figure 11-54 APR-L UNIT shows the location of the switches. The dip switches (DSW) allow a technician to configure the unit for specific settings.
Page 667: Figure 11-55 Separate Tilt Leg From Leg Support
UNIVERGE SV8100/SV8300 Issue 1.0 To prevent possible damage to the APR-L UNIT or the DTL/ITL multiline terminal during installation or removal, disconnect the line cord/LAN cable and the AC/DC adapter from the DTL/ITL multiline terminal. Unplug the line cord from the keyset.
Page 668: Figure 11-56 Bottom Option Interface Knockout
Issue 1.0 UNIVERGE SV8100/SV8300 Bottom Option Knockout Interface Figure 11-56 Bottom Option Interface Knockout Using the exposed Bottom Option Interface as a guide, install the APR-L UNIT in the bottom of the DTL/ITL multiline terminal. Push down until left and right tabs are seated (Refer to...
Page 669: Figure 11-58 Ferrite Bead With Apr Adapter
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 11-58 Ferrite Bead with APR Adapter Plug the end of the line cord for the analog device which has the ferrite bead closest to it into the jack on the adapter. Connect the opposite end to the analog device.
Page 670: Figure 11-59 Psa-L Unit
Issue 1.0 UNIVERGE SV8100/SV8300 12.5 PSA-L (BK) UNIT PSA-L (WH) UNIT The PSA-L UNIT (Power Save Adapter), an optional adapter for the ITL/DTL Terminals, is used with IP telephones to make or receive a call using the Public Switched Telephone Network (PSTN) when a call cannot be made or received using the Local Area Network (LAN).
Page 671: Figure 11-60 Psa-L Unit Connections
UNIVERGE SV8100/SV8300 Issue 1.0 PSTN DTMF/DP Figure 11-60 PSA-L UNIT Connections 12.5.1 Installing the PSA-L Adapter Before installing or removing the PSA-L adapter, remove the line cord, LAN cable, and then AC adapter from the outlet. Turn multiline terminal upside down.
Page 672: Figure 11-61 Separate Tilt Leg From Leg Support
Issue 1.0 UNIVERGE SV8100/SV8300 Stoppers Tilt Leg Figure 11-61 Separate Tilt Leg from Leg Support Push the two stopper tabs through the slots to separate the tilt leg from the leg support. Lay the tilt leg and the leg support flat.
Page 673: Figure 11-63 Bottom Of Multiline Terminal (Legs Removed)
UNIVERGE SV8100/SV8300 Issue 1.0 Push latch to right to unlock the cradle unit. Then push the cradle unit forward to separate from the terminal body. Latch Figure 11-63 Bottom of Multiline Terminal (Legs Removed) Fit the projections on the side of the PSA-L UNIT into the guide holes on the side of the terminal and pull toward you until the PSA-L UNIT snaps into place.
Page 674: Figure 11-65 Grooved Cutout For Serial Cable
Issue 1.0 UNIVERGE SV8100/SV8300 Gently press the serial cable into the grooved cutout for the cable. Cable Groove Figure 11-65 Grooved Cutout for Serial Cable Connect the serial connection cord (refer to Figure 11-64 Attach PSA-L Unit to the Multiline Terminal on page 11-83) from the PSA-L UNIT to the terminal body.
Page 675: Figure 11-67 Insert Connector For Handset Use
UNIVERGE SV8100/SV8300 Issue 1.0 For the Handset, set the connector in place. Figure 11-67 Insert Connector for Handset Use Attach the analog trunk cable and the handset cable. Refer to Figure 11-60 PSA-L UNIT Connections on page 11-81. Reinstall the legs, pushing upwards until both locks snap into place.
Page 676: Figure 11-69 Remove Numbered Keypad
Issue 1.0 UNIVERGE SV8100/SV8300 Pull tab down and lift out the numbered keypad panel. Figure 11-69 Remove Numbered Keypad Install the new keypad panel supplied with the PSA-L UNIT. Figure 11-70 Install Numbered Keypad Reinstall both plastic panels to the front of the multiline terminal...
Page 677: Figure 11-71 Install Plastic Panels
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 11-71 Install Plastic Panels Connect the line cord to the adapter. Connect the user system (KTS or PBX) cable. If required, remove the side panel from the original cradle unit. 12.5.2 Using the PSA-L Adapter...
Page 678 Issue 1.0 UNIVERGE SV8100/SV8300 Answering Calls: If you receive a call via PSTN during a conversation via LAN, answer the call by completing the LAN call and placing the handset back into the cradle. Change the LAN/PSTN Change Switch to PSTN and then lift the handset to answer the call.
Page 679: Table 11-4 Rj-61 Cable Connector
UNIVERGE SV8100/SV8300 Issue 1.0 When connecting the RJ-61 cables to the COIU Blade, note the position of the Power Failure connector. Do not confuse connector CN3 as the CN2 trunk connector. 13.2 Connector Pin-Outs on COIU Blade for Power Failure Circuits...
Page 680: Figure 11-72 Power Failure Connector (Cn3) Shown On Cd-4Cotb Blade
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 11-72 Power Failure Connector (CN3) Shown on CD-4COTB Blade 11 - 90 Installing SV8100/SV8300 Optional Equipment...
Page 681 term Installing D Series i Telephones ECTION ENERAL NFORMATION The SV8100/SV8300 system supports several different Electra Elite IPK II term Series i Multiline Terminals and an Attendant Console. This chapter describes each terminal and the console and provides instructions for attaching the terminals to the system and for wall mounting.
Page 682: Figure 12-1 Dtr-2Dt-1 Tel
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 12-1 DTR-2DT-1 TEL term 12 - 2 Installing D Series i Telephones...
Page 683: Figure 12-2 Dtr-4D-1 Tel
UNIVERGE SV8100/SV8300 Issue 1.0 DTR-4D-1 TEL This digital display Multiline Terminal has four multifunction keys, four programmable line keys (each with a 2-color LED), nine function keys, two volume keys, four softkeys, a built-in speakerphone, and a large LED to indicate incoming calls and messages.
Page 684: Figure 12-3 Dth-8-1 Tel Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 DTH-8-1/2 TEL This digital nondisplay Multiline Terminal has eight programmable line keys (each with a 2-color LED), a built-in speakerphone, headset jack, a large LED to indicate incoming calls and messages, and compatibility with AD(A)-R, AP(A)-R, AP(R)-R, CT(A)-R, CT(U)-R, or HF-R, Unit. This terminal is available in black or white.
Page 685: Figure 12-4 Dth-8D-1 Tel Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 DTH-8D-1/2 TEL This digital Multiline Terminal has eight programmable line keys (each with the 2-color LED), a built-in speakerphone, headset jack, a large LED to indicate incoming calls and messages, and compatibility with AD(A)-R, AP(A)-R, AP(R)-R, CT(A)-R, CT(U)-R, HF-R, or IP-R Unit. This terminal is available in black or white.
Page 686: Figure 12-5 Dth-16-1 Tel Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 DTH-16-1/2 TEL This digital nondisplay Multiline Terminal has 16 programmable line keys (each with a 2-color LED), a built-in speakerphone, headset jack, a large LED to indicate incoming calls and messages, and compatibility with AD(A)-R, AP(A)-R, AP(R)-R, CT(A)-R, CT(U)-R, or HF-R, Unit. This terminal is available in black or white.
Page 687: Figure 12-6 Dth-16D-1 Tel Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 DTH-16D-1/2 TEL This digital Multiline Terminal has 16 programmable line keys (each with a 2-color LED), a built-in speakerphone, headset jack, a large LED to indicate incoming calls and messages, and compatibility with AD(A)-R, AP(A)-R, AP(R)-R, CT(A)-R, CT(U)-R, HF-R, or IP-R Unit. This terminal is available in black or white.
Page 688: Figure 12-7 Dth-16(Bl)-1 Tel Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 DTH-16(BL)-1/2 TEL This digital Multiline Terminal has 16 programmable line keys (each with a 2-color LED), a built-in half-duplex speakerphone, headset jack, a large LED to indicate incoming calls and messages, and compatibility with AD(A)-R, AP(A)-R, AP(R)-R, CT(A)-R, CT(U)-R, HF-R, or IP-R Unit. This terminal is available in black or white.
Page 689: Figure 12-8 Dth-16Ld-1 Tel Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 DTH-16LD-1/2 TEL This digital Multiline Terminal has 16 programmable line keys, a built-in speakerphone, headset jack, a large LED to indicate incoming calls and messages, and compatibility with AD(A)-R, AP(A)-R, AP(R)-R, CT(A)-R, CT(U)-R, HF-R or IP-R Unit. This terminal is available in black or white.
Page 690: Figure 12-9 Dth-32D-1 Tel Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 DTH-32D-1 TEL This digital Multiline Terminal has 32 programmable line keys (each with a 2-color LED), a built-in speakerphone, headset jack, a large LED to indicate incoming calls and messages, and compatibility with AD(A)-R, AP(A)-R, AP(R)-R, CT(A)-R, CT(U)-R, HF-R, or IP-R Unit. This terminal is available in black or white.
Page 691: Figure 12-10 Dcr-60-1( ) Console
UNIVERGE SV8100/SV8300 Issue 1.0 2.10 DCR-60-1( ) Console The Attendant Console has 115 programmable line keys (each with a 2-color LED). An AC adapter is required and provided with the Attendant Console. Figure 12-10 DCR-60-1( ) Console System Hardware Manual...
Page 692: Figure 12-11 Connecting A Multiline Terminal To The System
Issue 1.0 UNIVERGE SV8100/SV8300 ECTION ONNECTING A ULTILINE ERMINAL TO THE YSTEM This instruction applies to all DTH/DTR/IP Electra Elite IPK Multiline Terminals except DTR-2DT-1 TEL. Plug the telephone cord into the modular jack on the bottom side of the Multiline Terminal.
Page 693: Figure 12-13 Connecting The Dcr Console To A Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 ECTION ONNECTING THE TTENDANT ONSOLE TO A ULTILINE ERMINAL An Attendant DCR-60-1 Console can be attached to a Multiline Terminal using the following procedure. Place the Multiline Terminal and the Attendant Console face down. Using the joining plate provided with the Attendant Console, attach the plate to the Multiline Terminal and the Attendant Console.
Page 694: Figure 12-15 Attendant Console And Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 When the Attendant Console and the Multiline Terminal are properly connected, they sit side-by-side as shown in Figure 12-15 Attendant Console and Multiline Terminal. Use only the AC adapter, provided with the Attendant Console. Using a different AC adapter may cause problems.
Page 695: Figure 12-17 Installing Line Card And Plastic Panel On A Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 ECTION NSTALLING ARDS AND LASTIC ANELS Installing the Line Card and Plastic Panel Line key designations are entered on the line card that is then placed on the telephone to provide a quick reference of key designations. The line cards can be changed as necessary.
Page 696: Figure 12-19 Removing The Plastic Panel From The Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 Removing the Plastic Panel Lift up on the plastic panel as illustrated in Figure 12-19 Removing the Plastic Panel from the Multiline Terminal and remove it from the telephone. Figure 12-19 Removing the Plastic Panel from the Multiline Terminal...
Page 697: Figure 12-21 Attaching Directory Card Holder To The Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 Locate the two grooves on the top of the telephone as illustrated in Figure 12-21 Attaching Directory Card Holder to the Multiline Terminal. Push the directory card holder into the grooves on the Multiline Terminal until they snap into place.
Page 698: Figure 12-22 Removing The Button Set From A Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 ECTION NSTALLING A UTTON ET ON A ULTILINE ERMINAL The BS( )-R Unit button set can be installed on a Multiline Terminal to accommodate French and Spanish languages. The keypad provides the appropriate language designations. Remove the plastic cover. (Refer to paragraph 6.2 Removing the Plastic Panel...
Page 699: Figure 12-24 Raising The Height On The Dth/Dtr Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 ECTION DJUSTING THE EIGHT ON A ULTILINE ERMINAL The base plate on the Multiline Terminal is hinged to allow the height of the terminal to be raised or lowered. Grasp in the middle of the hollow spaces at the top and pull up until the retaining tabs click to raise the base plate.
Page 700: Figure 12-26 Removing Base Plate
Issue 1.0 UNIVERGE SV8100/SV8300 ECTION EMOVING OR NSTALLING THE LATE ON A ULTILINE ERMINAL DTH/DTR Multiline Terminals come equipped with a base cover. 10.1 Removing the Base Plate Extend the base plate to maximum height. Press the tabs as illustrated in...
Page 701: Figure 12-27 Installing Base Plate
UNIVERGE SV8100/SV8300 Issue 1.0 10.2 Installing the Base Plate Line up the four tabs on the extended base cover with corresponding slots on the Multiline Terminal as illustrated in Figure 12-27 Installing Base Plate. Slide the cover in the direction of the arrows until it clicks in place.
Page 702: Figure 12-28 Removing The Hanger Hook On A Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 ECTION OUNTING ULTILINE ERMINALS You can wall mount a DTH/DTR connection Multiline Terminal (except for DTR-2D-1 TEL) using the base cover or an optional wall mount unit. A wall mount unit must be used if adapters are installed on the Multiline Terminal.
Page 703: Figure 12-30 Removing The Cutout
UNIVERGE SV8100/SV8300 Issue 1.0 11.1.2 Wall Mounting the Telephone Extend and remove the base cover from the telephone. Refer Section 10 Removing or Installing the Base Plate on a Multiline Terminal. Remove cutout shown in Figure 12-30 Removing the Cutout.
Page 704: Figure 12-32 Wall Mounting The Base Plate
Issue 1.0 UNIVERGE SV8100/SV8300 Turn the base cover upside down, feed the line cord through the cutout and attach the cover to the wall using six screws as shown in Figure 12-32 Wall Mounting the Base Plate. Figure 12-32 Wall Mounting the Base Plate Install the Multiline Terminal over the four tabs on the base cover, and push down until it clicks in place.
Page 705: Figure 12-34 Plugging In Line Cord
UNIVERGE SV8100/SV8300 Issue 1.0 Plug the line cord into the Multiline Terminal as illustrated in Figure 12-34 Plugging in Line Cord. Figure 12-34 Plugging in Line Cord Push spare line cord behind the Multiline Terminal as shown in Figure 12-35 Hiding Excess Cord.
Page 706: Figure 12-36 Removing The Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 11.1.3 Removing the Wall Mounted Multiline Terminal from the Base Plate To remove the Multiline Terminal, press the tabs at the bottom as shown in Figure 12-36 Removing the Multiline Terminal, and push up on the Telephone until it comes loose.
Page 707: Figure 12-38 Wall Mounted Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 Hang the Multiline Terminal on the base cover. Figure 12-38 Wall Mounted Multiline Terminal Because of strength variation in switch boxes, this method is not recommended. System Hardware Manual 12 - 27...
Page 708: Figure 12-39 Attaching The Wall Mount Unit To The Wall
Issue 1.0 UNIVERGE SV8100/SV8300 ECTION OUNTING A ULTILINE ERMINAL USING THE OUNT (WM-R U The Wall Mount Unit is used to attach any DTH/DTR connection Multiline Terminal (except the DTR-2DT-1 TEL) to the wall. This unit connects to the back side of the telephone.
Page 709: Figure 12-40 Attaching The Multiline Terminal To The Wall Mount Unit
UNIVERGE SV8100/SV8300 Issue 1.0 Multiline Terminal Figure 12-40 Attaching the to the Wall Mount Unit Plug the line cord into the Multiline Terminal as illustrated in Figure 12-41 Plugging in Line Cord. Figure 12-41 Plugging in Line Cord System Hardware Manual...
Page 710: Figure 12-42 Hiding Excess Cord Behind The Wall Mount Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Push spare line cord behind the Multiline Terminal as shown in Figure 12-42 Hiding Excess Cord Behind the Wall Mount Unit. Figure 12-42 Hiding Excess Cord Behind the Wall Mount Unit 12.1 Removing the Wall Mounted Multiline Terminal from the Wall...
Page 711: Figure 12-44 Mounting Wall Mount Unit On The Switch Box
UNIVERGE SV8100/SV8300 Issue 1.0 12.2 Mounting the Wall Mount Unit on a Switch Box Locate the screw holes on the wall mount unit and hang the cover over the screws on the switch box as illustrated in Figure 12-44 Mounting Wall Mount Unit on the Switch Box.
Page 712 Issue 1.0 UNIVERGE SV8100/SV8300 THIS PAGE INTENTIONALLY LEFT BLANK term 12 - 32 Installing D Series i Telephones...
Page 713: Figure 13-1 Raising The Base Plate
term Installing D Series i Optional Equipment ENERAL NFORMATION ECTION The SV8100/SV8300 system provides several adapters that allow term peripheral equipment to be attached to the IPK II D Series i Multiline Terminals. This optional equipment enhances the SV8100/SV8300 system Chapter and can be purchased separately as a customer business grows.
Page 714: Figure 13-2 Removing The Multiline Terminal Base Plate
Issue 1.0 UNIVERGE SV8100/SV8300 Press down on the tabs indicated in Figure 13-2 Removing the Multiline Terminal Base Plate, and push forward on the base plate to remove it. Figure 13-2 Removing the Multiline Terminal Base Plate When an adapter is installed for the first time, the base cover on the Multiline Terminal must be modified.
Page 715: Figure 13-3 Modifying Base Plate For Adapter Installation
UNIVERGE SV8100/SV8300 Issue 1.0 Remove for AC Remove for Cable Adapter Plug Connector Remove for Adapter Figure 13-3 Modifying Base Plate for Adapter Installation System Hardware Manual 13 - 3...
Page 716 Issue 1.0 UNIVERGE SV8100/SV8300 ECTION NSTALLING DAPTERS AC-2R/AC-3R Unit (AC Adapter) This unit shown in Figure 13-4 AC-2R/AC-3R Unit (AC Adapter) provides power to ancillary devices or to an Attendant Console. The AC-2R/AC-3R Unit must be connected to some adapters that are installed on a Multiline Terminal.
Page 717: Figure 13-4 Ac-2R/Ac-3R Unit (Ac Adapter)
UNIVERGE SV8100/SV8300 Issue 1.0 The Plug Puller shown in Figure 13-4 AC-2R/AC-3R Unit (AC Adapter) is a hollow cylindrical sleeve with a post and a circular rim on the base. The plug of the adapter is inserted in this hole, and the sleeve is pulled over the back of the plug to seat the post that can then be used to unplug the adapter.
Page 718: Figure 13-6 Ad(A)-R Unit
Issue 1.0 UNIVERGE SV8100/SV8300 AD(A)-R Unit (Ancillary Device Adapter) This Ancillary Device Adapter, shown on Figure 13-6 AD(A)-R Unit, allows connection of a tape recorder to all Multiline Terminals except the DTR-2DT-1. Figure 13-6 AD(A)-R Unit Figure 13-7 Connecting a Multiline Terminal to a Recording Device using an...
Page 719: Figure 13-8 Ad(A)-R Unit Connection Without Pause Control
UNIVERGE SV8100/SV8300 Issue 1.0 3.2.1 Connecting Cables to the AD(A)-R Unit The first step in installing the AD(A)-R Unit is to connect the cables between the recording device and the AD(A)-R Unit. Cable terminal connectors are located on the side of the AD(A)-R Unit.
Page 720: Figure 13-10 Removing Ad(A)-R Unit Cover
Issue 1.0 UNIVERGE SV8100/SV8300 Remove Screw Figure 13-10 Removing AD(A)-R Unit Cover Locate the adapter terminals on the unit. Remove the cap on the adapter terminal to expose the metal receptacle. Push the cable in the applicable receptacle, and replace the cap. Line up the slot on the cap with the slot on the metal receptacle to ensure proper contact.
Page 721: Table 13-1 Ad(A)-R Unit Cable Connections
UNIVERGE SV8100/SV8300 Issue 1.0 Table 13-1 AD(A)-R Unit Cable Connections Terminal Cables to Connect Terminal Specifications Number When warning tone is not being Input Terminal: T1 and T2 are enabled sent from the recorder, connect wire for tone generating device when pair input from tone generator to switches SW1-3 and SW1-4 are OFF.
Page 722: Figure 13-12 Ad(A)-R Unit Cable Access Port
Issue 1.0 UNIVERGE SV8100/SV8300 Table 13-1 AD(A)-R Unit Cable Connections (Continued) Terminal Cables to Connect Terminal Specifications Number Notes: When recording in handsfree (half-duplex) mode using the built-in speakerphone, the record warning tone may not be audible to the far-end party.
Page 723: Figure 13-13 Ad(A)-R Switch Default Settings
UNIVERGE SV8100/SV8300 Issue 1.0 3.2.2 Switch Settings The AD(A)-R Unit has two switch locations SW1/SW2. The location of the switches on the AD(A)-R Unit is illustrated in Figure 13-13 AD(A)-R Switch Default Settings. The dip switches (DSW) allow a technician to configure the unit for specific settings.
Page 724 Issue 1.0 UNIVERGE SV8100/SV8300 Table 13-2 AD(A)-R Unit Switch Settings (Continued) Switch Description/Settings Output Hook Signal to External Device DSW 1 On = Output Off = No Output (Default) Record Confirmation Tone DSW 2 On = Tone On Off = Tone Off (Default)
Page 725: Figure 13-14 Attaching The Ad(A)-R Unit To The Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 13-14 Attaching the AD(A)-R Unit to the Multiline Terminal Replace the base plate (or wall mount unit) and attach the line cord. Refer to Section 3 Connecting a Multiline Terminal to the System on page 12-12.
Page 726: Figure 13-15 Connecting A Multiline Terminal To An Analog Telephone Using An Ap(A)-R Unit/Ap(R)-R Unit (Example)
Issue 1.0 UNIVERGE SV8100/SV8300 AP(A)-R Unit/AP(R)-R Unit (Port Adapter) The AP(A)-R Unit Analog Port Adapter without Ringer or the AP(R)-R Unit Analog Port Adapter with Ringer is used to install a Single Line Terminal, Modem, Credit Card Reader, Wireless Headset, or other compatible analog device.
Page 727: Figure 13-16 Ap(A)-R Unit/Ap(R)-R Unit Switches
UNIVERGE SV8100/SV8300 Issue 1.0 3.3.1 Switch Settings The AP(A)-R Unit and AP(R)-R Unit have three switch locations. Refer to Table 13-3 AP(A)-R/AP(R)-R Unit Switch Settings for a description of each switch and an explanation of the settings. Figure 13-16 AP(A)-R Unit/AP(R)-R Unit Switches...
Page 728: Figure 13-17 Attaching The Ap(A)-R/Ap(R)-R Unit To The Multiline Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 3.3.2 Installing AP(A)-R or AP(R)-R Unit on a Multiline Terminal The AP(A)-R or AP(R)-R Unit should be installed after the switches are set. When wall mounting the Multiline Terminal, a WM-R Unit must be used. Refer to Section 11 Wall Mounting Multiline Terminals on page 12-22.
Page 729 UNIVERGE SV8100/SV8300 Issue 1.0 Figure 13-17 Attaching the AP(A)-R/AP(R)-R Unit to the Multiline Terminal System Hardware Manual 13 - 17...
Page 730: Figure 13-18 Installing The Ferrite Core On The Ap(A)-R/Ap(R)-R Unit
Issue 1.0 UNIVERGE SV8100/SV8300 Install the ferrite core (provided with the unit) about two inches from the line cord plug. AP(A)-R Unit AP(R)-R Unit Figure 13-18 Installing the Ferrite Core on the AP(A)-R/AP(R)-R Unit Connect the line cord to the unit, limiting the cable length from the AP(A)/AP(R)-R Unit to the Single Line Telephone to a maximum of 50 feet.
Page 731: Figure 13-19 Ct(A)-R Unit
UNIVERGE SV8100/SV8300 Issue 1.0 CT(A)-R Unit (Computer Telephony Adapter) The Computer Telephony Adapter, CT(A)-R Unit allows a Multiline Terminal to be connected to a PC. The PC can perform all Multiline Terminal functions using a TAPI-compatible application software (Microsoft Telephony Application Programming Interface).
Page 732: Figure 13-21 Attaching The Ct(A)-R Unit To The Terminal
Issue 1.0 UNIVERGE SV8100/SV8300 3.4.1 Installing the CT(A)-R Unit The CT(A)-R Unit should be installed before connecting the PC and before connecting the ESI port to the Multiline Terminal. When wall mounting the Multiline Terminal, a WM-R Unit must be used.
Page 733 UNIVERGE SV8100/SV8300 Issue 1.0 CT(A)-R Unit Figure 13-21 Attaching the to the Terminal Replace the base plate (or wall mount unit) and attach the line cord. Refer to Section 3 Connecting a Multiline Terminal to the System on page 12-12.
Page 734: Figure 13-22 Connecting The Rs-232C Cable To The Ct(A)-R Unit
Issue 1.0 UNIVERGE SV8100/SV8300 3.4.2 Connecting the CT(A)-R Unit to the PC Connect RS-232C cable from the PC to the CT(A)-R Unit as shown Figure 13-22 Connecting the RS-232C Cable to the CT(A)-R Unit. Figure 13-22 Connecting the RS-232C Cable to the CT(A)-R Unit 3.4.3...
Page 735: Figure 13-24 Ct(U)-R Unit
UNIVERGE SV8100/SV8300 Issue 1.0 CT(U)-R Unit (Computer Telephony Adapter) The CT(U)-R Unit Computer Telephony Adapter allows a Multiline Terminal to be connected to a PC using the PC USB port. Connecting using the USB port provides telephony and sound device control.
Page 736: Figure 13-25 Connecting A Multiline Terminal To A Pc Using A Ct(U)-R Unit (Example)
Issue 1.0 UNIVERGE SV8100/SV8300 Figure 13-25 Connecting a Multiline Terminal to a PC using a CT(U)-R Unit (Example) shows how the CT(U)-R Unit is connected to the ESI(8)-U( ) ETU and to the PC. The required AC-2R/AC-3R Unit is not shown.
Page 737: Figure 13-26 Attaching The Ct(U)-R Unit To The Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 Figure 13-26 Attaching the CT(U)-R Unit to the Multiline Terminal Replace the base plate (or wall mount unit) and attach the line cord. Refer to Section 3 Connecting a Multiline Terminal to the System on page 12-12.
Page 738: Figure 13-27 Connecting The Usb Cable To The Ct(U)-R Unit
Issue 1.0 UNIVERGE SV8100/SV8300 3.5.2 Connecting the CT(U)-R Unit to the PC Connect USB cable from the PC to the CT(U)-R Unit as shown in Figure 13-27 Connecting the USB Cable to the CT(U)-R Unit. Figure 13-27 Connecting the USB Cable to the CT(U)-R Unit 3.5.3...
Page 739: Figure 13-28 Attaching The Hf-R Unit To The Multiline Terminal
UNIVERGE SV8100/SV8300 Issue 1.0 4.1.1 Installing an HF-R Unit on any DTR/DTH Multiline Terminal (except DTR-2DT-1) With terminal upside down, facing from the bottom of the open cover, install this unit in terminal adapter Slot 1. Figure 13-28 Attaching the HF-R Unit to the Multiline Terminal...
Page 740: Figure 13-29 Microphone With Mute
Installing the External Microphone An external microphone can be installed on the HFU-U Unit. These instructions apply to the external microphone obtained from NEC. The microphone is equipped with a locking mute button and a red LED indicator that is off when the microphone is in mute.
Page 741: Figure 13-30 Adm Interface Unit
UNIVERGE SV8100/SV8300 Issue 1.0 Add on Module (ADM) The D16(LD)-R ADM creates a 16 button Phonebook directory. The interface for this unit shown in Figure 13-30 ADM Interface Unit is connected in the right adapter connector for the applicable multiline terminal. When another adapter needs to be added, this interface must be moved to the left adapter connector to preserve the cable integrity.
Page 742: Figure 13-31 Adm And Multiline Terminal With Base Covers Removed
Issue 1.0 UNIVERGE SV8100/SV8300 Table 13-4 DSW1 Switch Positions Series Keyset Name DSW1 Switch Positions DTR/H-(8)/(16)D-2( ) term Series i DTR/H -16LD-2( ) TEL DTR/H-16D(BL)-2( ) 1 2 3 4 5 6 7 8 Plug the interface unit into the right adapter connection as...
Page 743 UNIVERGE SV8100/SV8300 Issue 1.0 Install the connector plate provided with the ADM as shown in Figure 13-32 Installing the Connector Plate on the next page. The connector plate cannot be used with InMail terminals. Figure 13-32 Installing the Connector Plate...
Page 744 Issue 1.0 UNIVERGE SV8100/SV8300 Install the ADM and Multiline Terminal as shown on Figure 13-31 ADM and Multiline Terminal with Base Covers Removed on page 13-30. Figure 13-33 Installing Base Units on the Wall term 13 - 32 Installing D...
Page 745 Using the PTM or PTT handset on an NEC digital terminal prevents eavesdropping and eliminates the worry that privileged information could be transmitted without user authority. These handsets are also an ideal solution to filter unwanted audio transmissions from environments with ambient background noise.
Page 746 Issue 1.0 UNIVERGE SV8100/SV8300 - - NOTES - - term 13 - 34 Installing D Series i Optional Equipment...
Page 748 System Hardware Manual NEC Unified Solutions, Inc. Issue 1.0...

This manual is also suitable for:

Univerge sv8300

NEC Univerge SV8100 System Hardware Manual

Table of Contents

Chapter 1 Introduction to SV8100/SV8300

Chapter 2 SV8100 System Specifications

Section 4

Section 7

List of Figures

List of Tables

Chapter 3 SV8300 System Specifications

Chapter 4 Installing the SV8100 Chassis

Chapter 5 Installing the SV8300 Chassis

Chapter 6 Installing the SV8100/SV8300 Blades

Chapter 7 Installing DT300/DT700 Series (DTL/ITL) Digital and IP

Chapter 8 Installing SV8100/SV8300 Cordless Telephones

Chapter 9 Installing SV8100/SV8300 Wireless Telephones

Chapter 10 Installing SV8100/SV8300 Conference Solutions

Chapter 11 Installing SV8100/SV8300 Optional Equipment

Chapter 12 Installing D Series I Telephones

Chapter 13 Installing D Series I Optional Equipment

Quick Links

Chapters

Related Manuals for NEC Univerge SV8100

Summary of Contents for NEC Univerge SV8100