Related Manuals for Bosch CIB36 Series
Summary of Contents for Bosch CIB36 Series
- Page 1 CIB36... Installation Instructions...
- Page 5 ...
- Page 6 ...
- Page 7 ...
- Page 9 ...
- Page 10 ...
- Page 11 Transporting the appliance Installation preparation Unpack installation materials and accessories. ã Warning: To simplify installation, the packages are identifi ed with The appliance is very heavy. Handle it carefully, labels A, B, C and D corresponding with the manual as otherwise people helping to lift it could be hur sections.
- Page 12 Attaching the anti-tipping brackets to the wall ã Warning: Ensure that in the wall area there are no electrical wires or pipes which could be damaged by pipes. Risk of injury or damage! ã Warning: When installing or working with floor anchors always use protective glasses and other protective equipment or protective clothing –...
- Page 13 Attaching alternative anti-tilt device Important note: If the anti-tilt brackets cann ot be securely attached, a wooden beam can be used above the appliance as an alternative anti-tilt device. Care should be taken that there is not a gap between the appliance and the wooden beam.
- Page 14 Sliding the appliance into the installation niche Protect the mains lead from getting wedged under ã Caution: or behind the appliance. Be careful when sliding the appliance into the Recommended procedure: installation niche. Do not damage the water connection or power cord. Tie a piece of string in the middle of the power co and guide the string forwards over the appliance.
- Page 15 Adjusting the appliance in the niche Note: ...
- Page 16 Attach the covering ribs (b) onto the fastening Fastening the appliance to the sheets (above). niche ceiling Note: It is essential to attach the appliance to the ceiling of the cavity. Screw on the front bars of the fastening sheets (above) with the upper cabinets.
- Page 17 This is a special installation step. Checking that the finger guard Instructions are provided after moves easily section D. It is now essential to check that the finger guard m oves easily. At a later time any required corrections wi ll be more difficult.
- Page 18 Fastening the plinth strip Aligning the base cover Place base cover on the appliance (do not screw Note: on). Never cover the ventilation cracks in the base pane lling. Measure the difference in depth A between the Risk of damage to the appliance. base panelling and the base strip of the adjacent Nominal dimensions to be observed: lower cabinets.
- Page 19 Switching the appliance on for the first time The appliance should now be switched on for the fir time in order to ensure the accuracy of the followi mounting steps and with it, the appearance of the e ntire kitchen frontage. Open the appliance door.
- Page 20 Fastening the adjusting rib to the furniture door (refrigerator compartment) Measure distance A between the adjusting rail and the furniture parts above. Loosen the two nuts (a) and remove the adjusting rib (b). Mark this value A on the rear side of the furniture door.
- Page 21 Lengthen the markings to the parallels using an Pre-drill the holes. angle of contact. Tightly screw the adjusting rib. Apply the fixing ribs (b) and mark out the holes. Pre-drill the holes. Screw on the fixing ribs (b). Note: ...
- Page 22 Transfer the position of the fastening screws on the 11. Mounting the furniture door outer edge of the appliance door to the furniture (freezer compartment) door and mark. Note: Now attach the door handles which should have been screwed from behind! Remove fixing bracket (a) from the appliance door To do this, loosen the fastening screws (b) only.
- Page 23 10. S c rew nu t s onto the threaded rods of the adj u s ting Hang furniture door with th e adjusting rail onto the threaded rods ( 1.). rail and tighten! T h is way , the lateral adj u s tment of the door is fix e d.
- Page 24 Hang furniture door with th e adjusting rail onto the 10. Screw nuts onto the threaded rods of the adjusti threaded rods ( 1.). rail and tighten! This way, the lateral adjustment of the door is fixed. Lower furniture door and push the fixing brackets down over the fastening screws on the appliance door ( 2.).
- Page 25 Attach the finger protector with the screws on th Fasten the finger protector fixing brackets. When positioning the finger protector at the door ensure that the fixing holes in the cover strip correspond with the boreholes in the fixing brackets. Mark now the bottom edge of the finger protector and shorten accordingly.
- Page 26 Attach the covering bar above the adjusting ribs This is a special installation step. the freezer compartment drawer. Instructions are provided after section D. Tensioning the hinge springs (refrigerator compartment) Turn the setting screw with a cross head screwdrive I = Spring tensioned 0 = Spring released...
- Page 28 Robert Bosch Hausgeräte GmbH Carl-Wery-Straße 34 81739 München DEUTSCHLAND 9000668478 (9108)