Quick Links
Operating Instructions
1
Introduction
The remote control is designed to operate
For The UR5U-BH8000
the Scientific Atlanta Explorer 8000, Pioneer
Voyager DVR and the Pace Micro DVR
Cable Remote Control
Series. You can also control the majority of
TV, VCR, DVD and AUDIO equipment on the
market as shown below.
CABLE : Cable Converters
UR5U-BH8000
VCR
: VCRs and TV/VCRs
AUX : Audio Receivers, SAT, DVR, etc.
Replacing Batteries
2
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown In the
illustration below.
STEP3 Replace the battery compartment cover.
4
Operations
Default State:
Device Default: CABLE
Volume Default: You have the option of controlling
your TV volume and mute through the Cable box,
VCR or DVD. Refer to section G for programming the
volume and mute through your Cable box, VCR or
DVD.
Channel Default: You have the option of controlling
your CABLE channel and number keys through the
TV or VCR. Refer to section F for programming the
channel and number keys through your TV or VCR.
System On/Off button:
Universal Remote Control, Inc.
This button is designed to send out power
commands for two, three, four or all five devices with
www.universalremote.com
one button press. Please refer to section E for
OCE-0019C Rev 02(11/29/05)
details.
3
Button Functions
TV : Televisions
DVD : DVD Players
5
Programming the Remote Control
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three-digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit
code numbers are listed in the code table of the instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX)
STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and [SELECT]
button simultaneously for 3 seconds. The device LED will turn on indicating the unit is
ready to be programmed.
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED
is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number
assigned to your brand from the code tables.
C. To Find the Three Digit Code Number
*Tip : The equipment will turn off when the
That was Stored in the Device.
correct three-digit code number has
been entered. You can verify you have
STEP1 Press the [DEVICE] button (TV, VCR ,
selected the correct code by pressing
DVD or AUX) you wish to verify and
the [POWER] button, the equipment
the [SELECT] button simultaneously
should turn on or turn off.
for 3 seconds. The device LED will
turn on.
*Note : If there is more than one three-digit
number listed for your brand, try one
*Tip : The device LED will turn on for 20
code number at a time until your
seconds. The next step must be
equipment turns off.
entered while the LED is on.
STEP4 Store the three-digit code number
STEP2 Press the [INFO] button.
by pressing the same [DEVICE]
The device LED will blink number of times
button once again. The device LED
indicating the number of each digit of the
will blink twice to confirm that the
code number. Each digit is separated by a 1
code has been stored.
second interval of the LED being turned off.
*Note : Try all the functions on the remote
Example : One blink, three blinks and eight
control. If any of the functions do not
blinks with an interval of 1 second
work as they should, repeat from
of LED being turned off, indicates
Step 2 using the next three-digit code
the code number 138.
number from the same brand list.
Note : Ten blinks is equal to the number 0.
B. Auto Search Method.
D. Programming a second TV to AUX Mode.
If the three-digit code numbers assigned to
STEP1 Press the [AUX] button to be
your brand do not turn off your equipment or
programmed and the [SELECT] button
the code tables do not list your brand, you
simultaneously for 3 seconds.The
can use the Auto Search Method to find the
[AUX] device LED will turn on.
correct three-digit code number for your
*Tip : The device LED will turn on for 20
equipment by the following steps:
seconds. The next step must be
STEP1 Turn on the equipment you wish to
entered while the LED is on.
operate.
STEP2 Press the [TV] device button to pick
STEP2 Press the [DEVICE] button (TV, VCR,
up the TV code table.
DVD or AUX) to be programmed and
STEP3 Point the remote control toward the
the [SELECT] button simultaneously
equipment and enter the three-digit
for 3 seconds. The device LED will
code number assigned to your TV
turn on.
brand from the code tables.
*Tip : The device LED will turn on for 20
STEP4 Store the three-digit code number by
seconds. The next step must be
pressing the [AUX] button once
entered while LED is on.
again. The device LED will blink
twice to confirm that the code has
STEP3 Press the [CH+] or [CH-] button one
been stored.
at a time or keep it pressed. The
remote will emit a series of power
on/off commands. Release the
E. Programming the System On/Off Button.
[CH+] or [CH-] button as soon as the
equipment turns off.
This is designed to program the System On/Off
button so that it can send out up to five power
*Tip : You can verify that you selected the
on/off commands with one button press.
correct code by pressing the [POWER]
STEP1 Press the [CBL] button.
button. The equipment should either
turn on or turn off.
STEP2 Press the [SYSTEM ON/OFF] button
and the [SELECT] button
STEP4 Press the same [DEVICE] button to
simultaneously for 3 seconds. The
store the code. The device LED will
[CBL] button will turn on for 20
blink twice to confirm that the code
seconds.
has been stored.
STEP3 Press the [DEVICE] button and the
STEP1 Press the [CBL] button and the
[POWER] button you wish to store in
[SELECT] button simultaneously
the [SYSTEM ON/OFF] button and
for 3 seconds.
repeat this until you stored all the
The [CBL] device LED will turn on.
power commands into the [SYSTEM
*Tip : The device LED will turn on for 20
ON/OFF] button.
seconds. The next step must be
STEP4 Press the [CH+] button to save the
entered while the LED is on.
power commands you stored. The
[CBL] button will blink twice to
STEP2 Press the [VOL +] button.
confirm the saving.
STEP3 Press the [CBL] button.
The device LED will blink twice to
F. Programming Channel Control.
confirm the programming.
By following the steps below, the user can
To return to original state:
program the channel controls (Channel Up,
If you wish to restore the TV volume
Channel Down and Last) from one device to
control in CBL mode, repeat the above
operate in another device mode. The default
steps by pressing [TV] in STEP3 .
channel control settings on the remote
control are as follows:
H. Low Battery Warning.
CBL : CBL
T V : CBL
When the batteries are low and need to be
VCR : CBL
DVD : DVD
replaced with fresh batteries, the remote
AUX: AUX
control LED will blink 2 times in sequence
whenever a [POWER] button is pressed to
If you wish to store the TV channel control in
turn on equipment.
TV mode, use the following steps.
STEP1 Press the [TV] button and the
I. Memory Lock System.
[SELECT] button simultaneously for
3 seconds.
This remote control is designed to retain
The [TV] device LED will turn on.
programmed memory for 10 years even
after batteries are removed from the
*Tip : The device LED will light on for 20
remote control.
seconds. The next step must be
entered while the LED is on.
J.Write your device Set-up codes.
STEP2 Press the [VOL -] button.
STEP3 Press the [TV] button.
TV
Set-up Code Number:
The device LED will blink twice to
VCR Set-up Code Number:
confirm the programming.
DVD Set-up Code Number:
To return to original state:
AUX Set-up Code Number:
If you wish to restore the CABLE channel
control in TV mode, repeat the above steps
by pressing [CBL] in STEP3 .
G. Programming Volume Control.
By following the steps below, the user can
program the volume controls (Volume Up,
Volume Down and Mute) from one device to
operate in another device mode. The default
volume control settings on the remote
control are as follows:
CBL : TV
T V : TV
VCR : TV
DVD : TV
AUX : AUX
If you wish to store the CBL volume control in
CBL mode, use the following steps.
Related Manuals for Universal Remote Control UR5U-BH8000
Summary of Contents for Universal Remote Control UR5U-BH8000
- Page 1 Operating Instructions Introduction The remote control is designed to operate For The UR5U-BH8000 the Scientific Atlanta Explorer 8000, Pioneer Voyager DVR and the Pace Micro DVR Cable Remote Control Series. You can also control the majority of TV, VCR, DVD and AUDIO equipment on the market as shown below.
- Page 2 Pioneer Voyager DVR, Pace Micro 056 074 091 155 081 120 PHILIPS DVR Series. GIBRALTER 004 073 PIONEER UR5U-BH8000 GOLDSTAR / LG 004 106 119 110 112 113 127 143 084 POLAROID Motorola DCT6208 GRUNPY 028 043 PORTLAND Motorola DCT2XXX and...