SY MFT62 Installation Manual

6 input / 2 output multi-format switcher
MFT62
Installation Guide
MFT62
6 Input / 2 Output Multi-Format Switcher
4 HDMI, DisplayPort and VGA inputs with independent
HDMI and HDBaseT outputs
4K UHD
SY Electronics Ltd., 7 Worrall Street, Salford, Greater Manchester, M5 4TH
Tel: +44 (0)161 868 3450 – Fax: +44 (0)161 868 3459
Web: www.sy.uk
Table of Contents
loading

Summary of Contents for SY MFT62

  • Page 1 6 Input / 2 Output Multi-Format Switcher 4 HDMI, DisplayPort and VGA inputs with independent HDMI and HDBaseT outputs 4K UHD SY Electronics Ltd., 7 Worrall Street, Salford, Greater Manchester, M5 4TH Tel: +44 (0)161 868 3450 – Fax: +44 (0)161 868 3459 Web: www.sy.uk...
  • Page 2: Front Panel

    MFT62 The MTF62 is a 4K 6-input to 2 output Mutli-Format Switcher and HDBaseT Transmitter that provides the following features:  4x HDMI inputs (4K UHD)  1x DisplayPort input  1x VGA input  Local HDMI output  Remote HDBaseT output ...
  • Page 3: Rear Panel

    IR output to control local devices from the remote location RS232 Pass-through RS232 for HDBaseT output RS232-CTL RS232 for controlling the MFT62 48V DC power input Using the MFT62 Connect the video inputs as required. Connect the video outputs as required.
  • Page 4: Front Panel Controls

    EDID setting for each input. Local Button The LOCAL button selects the signal source to send to the HDMI output of the MFT62. When the Local AUTO mode is off, repeated presses of the LOCAL button will switch sequentially through all the inputs, even if there is no signal present.
  • Page 5: Cascade Mode

    MFT62 Using an External Switches The MFT62 has an interface for Input selection, using simple external Push Button switches, as shown in the following schematic: For each connector, pin 1 is left-most when viewed from the rear of the MFT62.
  • Page 6 EDID setting to another value. Press and hold the Local button to accept the new setting. The MFT62 drops out of the manual EDID setting mode when a new setting is accepted or if there is no activity for about 10 seconds, at which time the MFT62 will revert to the previously stored settings.
  • Page 7 ● ○ ○ ○ ○ The USER1 EDID, USER2 EDID and USER3 EDID memory locations on each input can only be programmed by using RS232 commands, and must contain valid EDID data before being used. Connecting the MFT62 V1.0 sy.uk...
  • Page 8: System Commands

    MFT62 RS232-CTL Commands All commands are sent at 57600 baud, 8 data bits, no parity and one stop bit. Commands are not case sensitive, but must always be followed by a carriage-return (0x0d). All spaces are optional, but are shown in the command tables for clarification.
  • Page 9 MFT62 Input EDID Setup Commands Set Input x EDID to the built-in EDID y Input y is 1- 4 = HDMI inputs 1 to 4 5 = DisplayPort input EDID y is one of the following (0-26): 0: 1080P_2CH(PCM) 1: 1080P_6CH...
  • Page 10 MFT62 SET INx EDID Uy DATAz Write EDID To User y Buffer of Input x {x[1~6], y[1~3], z[EDID Data] GET INx EDID Get Input x EDID Index {x[0~6](0All)} GET INx EDID y DATA Get Input x EDID y Data {x[1~5],y[0~26]}...
  • Page 11: Specification

    The signal for input x is turned off or disconnected. x = 0 - 6 The above messages are sent either when the MFT62 is powered up or whenever the status of the input signal changes. They are not included as part of the GET STA or STA commands.
  • Page 12 This product has a two year standard warranty, beginning from the date of purchase as stated on the sales invoice. For full details please refer to our Terms and Conditions. SY Product warranty is automatically void under any of the following conditions:  The product is already outside of its warranty period ...

Table of Contents