Related Manuals for Sony MAV-2000
Summary of Contents for Sony MAV-2000
- Page 1 MULTI ACCESS VIDEO AND AUDIO SERVER MAV-2000 INPUT AND OUTPUT PROCESSOR BOARD BKMA-2010 INSTALLATION MANUAL 1st Edition Serial No. 10001 and Higher: MAV-2000 Serial No. 10001 and Higher: BKMA-2010...
- Page 2 When this product is installed in a rack, please make verbunden werden, damit sich bei einer sure that the rack does not achieve hazardous Funktionsstörung die Stromversorgung zum Gerät condition due to uneven mechanical loading. jederzeit unterbrechen lä ß t. MAV-2000...
- Page 3 Mounting the unit with less than two persons may cause injury. Mount only with the specified support angles Support angles other than those specified for this unit may not be strong enough to support the unit, risking possible collapse and injury. 1 (P) MAV-2000...
-
Page 5: Table Of Contents
Connecting Connectors and Cables ............ 1-10 (E) 1-8. Connection ..................1-11 (E) 1-9. Checks after Connection ..............1-13 (E) 1-9-1. Checking MAV-2000 ............1-13 (E) 1-9-2. Checking BKMA-2010 ............1-13 (E) 1-9-3. Error Display ..............1-13 (E) 2. Service Overview 2-1. -
Page 7: Manual Structure
Manual Structure Purpose of this manual This manual is the installation manual of the MAV-2000 Multi Access Video and Audio Server. This manual is intended for use by trained system and service engineers, and describes the information regarding installation. Related manuals Besides this Installation Manual, the following manuals are available for the MAV-2000. -
Page 9: Installation
Section 1 Installation 1-1. Installation Procedure The installation procedure of the MAV-2000 is shown in the following flowchart. Refer to each item in this manual for details. Start Determination 1-2. Operating Conditions of Installation Space and Installation Space 1-3. Power Supply Rack Mounting 1-5. -
Page 10: Operating Conditions And Installation Space
Approx. 41 kg BKMA-2010 : Approx. 2.4 kg (per one set) To prevent overheating of the MAV-2000 ensure that there is good air circulation around the unit. Do not install the unit in humid or dusty environment. Do not stack the units. - Page 11 Do not stop the fan or block the ventilatior because this unit is air-cooled by the fan on the side view of the unit and the power supply. If not, a fire or failure may occur. 161.7 105.3 Unit : mm 1-3 (E) MAV-2000...
-
Page 12: Power Supply
. For a distributor box in the electrical system, use appropriate one with enough capacity for the rush curent mensioned above. Connect the power cord to the outlet directly without using an extension cord. For the customers outside the area as shown above. Please consult with local Sony’s sales/service office. 1-4 (E) MAV-2000... -
Page 13: Installation Of Option Boards
(such as slot 1, slot 1X, slot 1Y or the like) that correctly corresponds the front and rear of the MAV-2000. (Refer to the inscription on the front and rear panel indication.) Also, install the BKMA-2010 starting from the topmost slot in this order. - Page 14 (with drop-safe). open the front panel. 8. Remove the eight screws (PSW3 x 6) and remove the board fixing plate. RK4 x 16 Stopper Stopper Front panel PSW3 Board fixing plate 1-6 (E) MAV-2000...
-
Page 15: Rack Mounting
. Screw (RK5 x 14) 4 pcs . Ornamental Washer 4 pcs Standard Tightening Torque Screw Size Standard Tightening Torque M3.0 0.7 to 1.0 N.m (7 to 10 kgf.cm) M4.0 1.2 to 1.6 N.m (12 to 16 kgf.cm) B4 x 8 1-7 (E) MAV-2000... - Page 16 5. Attach the outer support assembly to the rack tempo- rarily. Nut plate 12.7 31.75 Bracket Inner support 12.7 B4 x 12 Bracket Rack side Main unit The projected side should face up. Rack side Outer support Outer support Unit : mm 1-8 (E) MAV-2000...
-
Page 17: Signal Input And Output
Pin No. Signal TX + TX _ RX + RK5 x 14 RX _ REMOTE : RS-422A (D-sub 9-pin, Female) Ornament washers RK5 x 14 Pin No. Signal GROUND OPERATE WARNING ERROR GROUND 1-9 (E) MAV-2000... -
Page 18: Connecting Connectors And Cables
1-7. Connecting Connectors and Cables When connecting cables to various connectors on the rear panel at the time of installing or servicing, connect the following connectors/cable or their equivalents. Connector of the MAV-2000 Side Matching Connector and Recommended Cable Print on Panel... -
Page 19: Connection
1-8. Connection Connect the MAV-2000 to the hard disk drive array units (abbreviates to RAID) MAV-S2000 as shown here: The rotary switch and the piano switch of MAV-S2000 are located behind the cover shown in Fig. 1. Remove the screw and the cover before switching them. - Page 20 .Center : bit 4 DOWN to the “1” position. SBX OUT1 SBX OUT2 Multi access HDD array unit (2) video/audio server MAV-S2000 MAV-2000 BNC cable 4bit piano switch SBX IN1 Rotary SW .Dual mode : bit 1 UP Set the first switch SBX IN2 .Terminal : bit 4 DOWN...
-
Page 21: Checks After Connection
Ensure that the unit is under the following conditions before checking of the LEDs’ operation. . The RAIDs connected to the MAV-S2000 are get up and running. . The REF VIDEO connector of the MAV-2000 receives a signal with a connected cable. 1-9-1. Checking MAV-2000 7-seg LEDs’... -
Page 23: Service Overview
Cleaning A filter is fitted on the rear side of the front panel assembly 1. Turn off the main power of the MAV-2000. of the unit. If accumulated dust on the filter impedes the 2. Fully loosen the three screws (with drop-safe). -
Page 24: Functional Descriptions Of Board Switches And Leds
Do not change the setting of the “Factory use” switches. Ref. No. Address Name Function Factory setting S201 (L-7) Abort switch For debug S202 (L-7) Reset switch Initializes the TM-37 board S203 (L-6) Test switch Factory use OPEN 1 2 3 4 5 6 7 8 2-2 (E) MAV-2000... - Page 25 Turns on when Ether is used for test Turns off D702 (L-3) Green Turns on when Ether is used for test Turns off D703 (L-2) Turns on when Ether is used for test Turns off ND201 (L-5) Flashes clockwise during normal run Flashes 2-3 (E) MAV-2000...
- Page 26 Name Function Factory setting S401 (A-3) Abort switch For debug S402 (A-9) All reset switch Initializes the MAV-2000 S403 (A-3) Reset switch Initializes the FM-62 board S404 (A-4) Test switch Factory use OPEN 1 2 3 4 5 6 7 8...
- Page 27 Turns on when SBX gate is open Turns off D406 (A-5) Green Not used Turns off D407 (A-5) Green Not used Turns off D408 (A-5) Green Time Slot (LSB) Flashes ND401 (A-7) Flashes clockwise during normal run Flashes 2-5 (E) MAV-2000...
-
Page 28: If-741 Board
Name Function Normal state D502 (K-11) Green Turns on when SBX SYNC is detected Turns off D503 (K-11) Green D504 (K-12) Green D505 (K-12) Green D506 (K-11) Green D507 (K-11) Green D508 (K-12) Green D509 (K-12) Green 2-6 (E) MAV-2000... -
Page 29: If-742 Board
Name Function Normal state D202 (G-11) Green Turns on when BINGO SLOT is “E” Turns off D203 (G-12) Green D204 (G-12) Green D205 (G-12) Green D206 (G-12) Green D207 (G-12) Green D208 (G-12) Green D209 (G-12) Green 2-7 (E) MAV-2000... -
Page 30: Dm-119 Board (Bkma-2010)
Do not change the setting of the “Factory use” switches. Ref. No. Address Name Function Factory setting S401 (L-8) Abort switch For debug S402 (L-7) Reset switch Initializes the DM-119 board S403 (L-7) Test switch Factory use OPEN 1 2 3 4 5 6 7 8 2-8 (E) MAV-2000... - Page 31 Turns on when Ch#Y port is recording Flashes when Ch#Y port is in playback Turns off while Ch#Y port is waiting ND401 (L-5) Rotates during normal operation (left half) (7-seg) ND402 (L-6) Rotates during normal operation (left half) (7-seg) 2-9 (E) MAV-2000...
- Page 33 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
- Page 34 BKMA-2010 (SY) Printed in Japan Sony Corporation MAV-2000 (SY) J, E 1999. 11 16 3-203-539-01 B&P Company ©1999...