Related Manuals for UFO GEMINI Series
Summary of Contents for UFO GEMINI Series
- Page 1 UFO LIGHTING FIBRE OPTIC & LED LIGHTING SYSTEMS REVISION GEMINI SLIMLINE LIGHT SOURCE USER GUIDE PLEASE READ THIS USER GUIDE BEFORE INSTALLING OPERATING OR PERFORMING MAINTENANCE ON THE LIGHT SOURCE UNIT...
- Page 2 INTRODUCTION Thank you for purchasing this UFO light source. To ensure that the light source is set up optimally and gives a long service life, please read this user guide before installing, operating or performing any maintenance on the unit.
-
Page 3: Installation
Align the plate against the rivets and secure the plate to the light source with the four plastic screws using an M4 pozi-drive screwdriver. Do not overtighten. The light source can now be fixed securely to the mounting surface. Note: Mounting plate diagram is indicative only. UFO LIGHTING... -
Page 4: Power Supply Requirements
INSTALLATION POWER SUPPLY REQUIREMENTS The light source is powered from a desktop 12V Dc power supply unit. The power supply unit is an IEc input device and caters for UK/European/other mains supplies using the relevant power cord. XXXXDMX / 10 V cONNEcTIONS GEM SLP XXXXM cONNEcTIONS GEM SLP... - Page 5 Multicomp SVP556-TA. The pin out details for the plugs are shown below. Either socket may be used as DMX in or DMX out. Note: UFO can supply converters for these light sources to allow them to be interfaced to standard 3 pin XLR connectors or RJ45 connectors.
- Page 6 Either socket may be used as 0-10V IN or 0-10V OUT Note: UFO can supply converters for these light sources to allow them to be interfaced to standard 3 pin XLR connectors or RJ45 connectors.
-
Page 7: Operation
2. Tilt the light source on its side and remove the screw from the base as shown below. 3. Slide the access cover down to remove and set the cover and screw aside. 4. Switch DIP switch 10 (top) to ON as shown below. 5. Replace access cover and securing screw. UFO LIGHTING... - Page 8 OPERATION SETTING THE DMX ADDRESS 1. Disconnect the light source from the mains supply. 2. Tilt the light source on its side and remove the screw from the base as shown below. 3. Slide the access cover down to remove and set the cover and screw aside. 4.
- Page 9 DMX B Start DMX B Start Dip Switches On Dip Switches On Channel # Channel # 1,2,4 1,3,4 2,3,4 1,2,3,4 1,2,3 1,2,3,4,5,6,7,8,9 Note: with dip switch 10 OFF, the light source will not illuminate unless a DMX signal is present. UFO LIGHTING...
- Page 10 OPERATION GEMINI 0-10 V MODELS ONLY USING THE LIGHT SOURCE Gemini 0-10V models allow the light output to be varied by applying a different voltage through the rear connectors. The following table represents light output percentage against approximate control value input. Light Output Voltage Note: the light source will not illuminate...
-
Page 11: Maintenance Log
MAINTENANCE MAINTENANCE LOG Date Maintenance Undertaken Note: a record of all maintenance MUST be kept in the table above, indicating what maintenance was undertaken and when. This MUST be dated for warranty purposes. UFO LIGHTING... -
Page 12: Troubleshooting
TROUBLESHOOTING PROCEDURES FOR ALL MODEL TYPES Problem Possible Cause(s) Remedy Unit is dead – Mains supply off Check supply & reinstate no light output Loose mains plugs Check plugs and LED power indicator on Plug fuse blown (UK) Check fuse. If blown, replace PSU is not illuminated PSU failed... - Page 13 10V signal present No 0-10V signal Carry out voltage and present 0-10V cable faulty polarity check on mini XLR plug. Repair as necessary Note: please complete relevant troubleshooting procedures before returning the unit to us for further investigation. UFO LIGHTING...
-
Page 14: Technical Specifications
TECHNICAL SPECIFICATIONS Description Details Port connector size 30mm diameter Fibre type Glass / PMMA Mains Supply Voltage 100-240V AC, 50-60Hz PSU Output 12V DC, 5A, 60W max. LED Power Min Ambient Temperature -10°C Max Ambient Temperature +45°C 60mm crossflow, 12V Led Type White light Manual models - dimming Functionality... - Page 15 NOTES UFO LIGHTING...
- Page 16 Europe • DESIGN SPECIFY BUILD INSTALL UFO Licht GmBH Universal Fiber Optic Lighting USA LLc Universal Fibre Optics Ltd Raum 2.38, Friendsfactory AG, 1749 Northgate Blvd, Home Place Gutenbergstraße 1, Sarasota, FL34234 coldstream, TD12 4DT Munchen 85737, Deutschland United Kingdom t.