What's Included The UPS is shipped with the following items: • User manual • USB cable: High speed 2.0 Standard Type A-B, 6 ft (1.8 m) NOTE: UPSwatch - Power Monitoring and Control Software is available for download at www solahd com.
2 0 Important Safety Instructions WARNING - Risk of electric shock, fire and personal injury SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries The UPS is intended for installation in a controlled environment Install the UPS in an indoor temperature- and humidity-controlled environment, free of •...
3 0 General Description 3 1 Front Panel LCD The LCD will show functions of the UPS operation status. • ON/OFF Button To turn the UPS on, press the ON/OFF button for two (2) seconds and the LCD will display UPS status. •...
Page 6
3 2 Rear Views Site Fault Indicator Breaker Port RJ 45 Input Surge Cable Protection Receptacles Rear View of SSW700 and SSW1000 Site Fault Indicator Optional SNMP Breaker Port Input RJ 45 Cable Surge Protection Receptacles Rear View of SSW1500 Page: 4...
5 0 Installation and Operation 5 1 Installation Requirements • Install the UPS in a controlled environment with adequate ventilation that is free of excessive dust and high humidity. • Avoid direct sunlight. • Maintain a clearance of 4 inches (100 mm) between the UPS rear panel and the wall and 1 inch (25.4 mm) between the UPS sides and the wall.
SSW UPS Rev.3 2019/05/30 6 0 LCD Screen Diagnostics 4.0 Interface Operation and Overview of LCD Panel operation and overview of LCD Panel Operation Mode Status Load and Battery capacity Number will be displayed in the following order Vin, Vo, load, battery capacity UPS Power on...
Page 10
Battery Mode Low Battery Battery voltage low, the battery alarm icon will flash once every 0.5 second. Battery Sleep Mode Battery Voltage Over Charge Battery voltage UVP, the battery stops to provide Battery voltage over charge, the battery alarm icon power, and the battery alarm icon will flash once will flash once every 0.5 second and display HI.
Page 11
OverLoad for Line and AVR Mode OverLoad 110% for Battery Mode When the UPS is within the overload limit, the When the UPS is within the overload limit, the alarm icon will flash once every 0.5 seconds. alarm icon will flash once every 0.5 seconds. When the UPS is beyond the overload limit, When the UPS is beyond the overload limit, the setup button will be locked.
7 0 Battery Replacement CAUTION Caution- risk of electrical shock Battery circuit is not isolated from AC input Hazardous voltage may exist between terminals and ground Test before touching Caution- risk of energy hazard Qualified service personnel only Refer to installation manual for battery replacement proper handling and disposal The battery may be replaced by qualified service personnel only Replace the battery with the same type and ratings...
Page 13
7 1 SSW700 and SSW1000 Battery Replacement Instructions Step 1: Using a Phillips head screwdriver, remove the Step 2: Place the faceplate on top of the UPS for easy access four (4) black screws located on the corners to the battery connections. of the front plate.
Page 14
Step 5: Pull on the white plastic tab in order to slide Step 6: Disconnect the jumper between the battery packs. the battery pack out of the SSW UPS. Step 7: After completing the previous steps, the result Step 8: Be sure to dispose of the batteries properly should resemble the image above.
Page 15
7 2 SSW1500 Battery Replacement Instructions Step 1: Using a Phillips head screwdriver, remove the Step 2: Place the faceplate on top of the UPS for easy access four (4) black screws located on the corners to the battery connections. of the front plate.
Page 16
Step 5: Pull on the white plastic tab in order to slide Step 6: Slide the battery pack out, refer to Step 3 the battery pack out of the SSW UPS. to disconnect the battery wire, then disconnect the jumper wires. Step 7: After completing the previous steps, the result Step 8: Be sure to dispose of the batteries properly should resemble the image above.
8 0 Troubleshooting Trouble Probable cause Solution UPS is powered off Press ON/OFF button for two (2) seconds. UPS nonresponsive Battery is defective Replace the battery. (No alarm and no light) UPS fault Contact Tech Support. Power cord is loose Re-plug the power cord.
9 0 Technical Specifications Catalog Number SSW700 SSW1000 SSW1500 Topology Line Interactive sinewave Capacity (VA/W) 700/480 1000/750 1440/1200 Dimensions 9.09 x 6.69 x 12.4 9.09 x 6.69 x 12.4 9.09 x 6.69 x 16.97 Unit (H x W x D) - in (mm) (231 x 170 x 315) (231 x 170 x 315) (231 x 170 x 431)
Page 19
Battery Run-Time Chart (minutes)* SSW700 SSW1000 SSW1500 Load (%) Run-Time (minutes) 100% *NOTE: Run times in this table are approximate. Based on new, fully charged standard batteries at a temperature of 25°C (77°F) with 100% resistive UPS loading. Run times listed above can vary by ±5% due to manufacturing variances of the batteries.
Terms and Conditions of Sale. Note that unit specifications are subject to change without notice. Technical Support Website: www.solahd.com Technical Support E-Mail: [email protected] Toll-Free: (800) 377-4384 USA: (847) 268-6651 Warranty Please see the “Terms & Conditions of Sale” document within the UPS packaging.