Quick Links
HP10216 KIT
Chevrolet Silverado / GMC Sierra 1500
(2WD / 4WD)
*
†
† For short (69.3") and medium (78.7") truck bed lengths (Not for 97.6" Truck Beds)
Will not fit vehicles equipped with MagneRide.
* See application guide for proper fitment.
Use the most advanced air springs on the market to eliminate your
vehicle's sag, sway and bottoming out. Pacbrake air suspension levels
your truck's stance while providing added support for an overall smooth
and safe ride.
ECN 1-1789
Related Manuals for Pacbrake HP10216
Summary of Contents for Pacbrake HP10216
- Page 1 * See application guide for proper fitment. Use the most advanced air springs on the market to eliminate your vehicle’s sag, sway and bottoming out. Pacbrake air suspension levels your truck’s stance while providing added support for an overall smooth and safe ride.
-
Page 2: Kit Contents
Worm Gear Ring Clamp (2 ½" - 4 ½") HP1001 Worm Gear Ring Clamp (4½" - 6 ½") HP1377 AIR SPRING SUB GROUP HP10180 Fitting, Brass, Push HP1099 Tywrap C11618 Roll Plate HP10054 Pacbrake is a registered trademark of Pacbrake Co. L6360_Rev4_17.07.2018 ECN 1-1789... - Page 3 * Part F10 is only to be used with fifth wheel hitch applications ECN: MATERIAL: 12.1 WEIGHT: INTERPRET AL AND TOL PER ASME THIRD ANGLE Note: Passenger's side assembly shown. FRONT OF VEHICLE Pacbrake is a registered trademark of Pacbrake Co. L6360_Rev4_17.07.2018 ECN 1-1789...
-
Page 4: Before You Start
1. Ensure the application information is correct for the make, model and year of the vehicle you are installing the kit on. 2. Pacbrake recommends using a good quality anti-seize on all fasteners. This will reduce the chance of corrosion on the fasteners and will help facilitate removal, if required at a later date. - Page 5 LOCATION THAT MAKES IT POSSIBLE TO RUB A HOLE IN THE SIDE OF THE AIR SPRING, IT WILL BE NECESSARY TO RELOCATE IT AWAY FROM THE AREA WHERE THE AIR SPRING IS INSTALLED. Pacbrake is a registered trademark of Pacbrake Co. L6360_Rev4_17.07.2018 ECN 1-1789...
- Page 6 The figure 4C - 4D below shows both left and right hand assemblies ready for installation. Pacbrake is a registered trademark of Pacbrake Co. L6360_Rev4_17.07.2018 ECN 1-1789...
- Page 7 • Torque the U-bolts to 10 ft-lbs. Repeat on the other side. Pacbrake is a registered trademark of Pacbrake Co. L6360_Rev4_17.07.2018 ECN 1-1789...
- Page 8 ⁄ " socket through the hole in the side of the frame to hold the rear mounting bolt for torquing. NOTE: Long box models may require a short extension. Pacbrake is a registered trademark of Pacbrake Co. L6360_Rev4_17.07.2018 ECN 1-1789...
- Page 9 • Bend the large cable clamp slightly to obtain clearance of the hard brake lines. Mounted on top of the axle. • Insert the emergency brake cable into the large cable clamp. Pacbrake is a registered trademark of Pacbrake Co. L6360_Rev4_17.07.2018 ECN 1-1789...
- Page 10 CRIMP THE AIR LINE CAUSING IT TO LEAK AROUND THE O-RING SEAL. CUSTOMER PART #: ORIZED DISCLOSURE, USE OR MANUFACTURE IN WHOLE OR IN PART IS PROHIBITED. G DESIGN AND OTHER DISCLOSURES PROPERTY OF PACBRAKE CO. SURREY, B.C., CANADA • Place a ⁄ "...
- Page 11 2.5 - 4.5" in diameter. The larger worm gear clamps (F17) are intended to be used with an exhaust that is between 4.5 - 6.5" in diameter. Pacbrake is a registered trademark of Pacbrake Co. L6360_Rev4_17.07.2018 ECN 1-1789...
-
Page 12: Optional Accessories
(see Note below). OPTIONAL ACCESSORIES Pacbrake offers an optional dual needle air gauge to monitor the pressure in each spring from the vehicles cab. Pacbrake offers a full line of air compressors, air tanks and solenoids to control your air spring system.