Der Anschluss kann an die Auswerteeinheiten 022160.10 / 022160.20 / 022164 / 022200 oder 022200.10 erfolgen. Das IDENT-KEY Blockschloss empfängt über die Rosette den Code des verwendeten Schlüssels. Durch die internen Sensoren wird die Stellung des Schließbartes bzw. des Blockschlossriegels laufend überwacht.
Dabei muss darauf geachtet werden, dass an der Unterseite der Öffnung für den Profilhalbzylinder zur Verlegung des Flachbandkabels der Rosette ausreichend Platz vorhanden ist. Ebenso dürfen die Bohrungen für die IDENT-KEY Rosette nicht vergessen werden. 3. Blockschloss-Anschlusskabel im Türblatt verlegen. * Es ist zu beachten, dass sich hinter dem Blockschloss ein ausreichender Kabelvorrat der Blockschlosszuleitung befindet.
Page 5
Montage-Anschluss-Anleitung IK2-Blockschloss Ausschnitt IDENT-KEY- Türblatt Blockschloss Bohrungen für Rosettenbestigung (Verwendung der Bohrschablone) IDENT-KEY- Rosette Anschlusskabel Achtung! An dieser Stelle ausreichend Platz für Rosetten- Anschlusskabel vorsehen! 5. Rosette sowie Innenschild aufsetzen und Gewindehülsen leicht anziehen. Dann wird der Zylinder durch die Rosette in die Zylinderöffnung des Blockschlosses geschoben Schließnase in Richtung zum Stulp,...
Page 6
Montage-Anschluss-Anleitung IK2-Blockschloss Einbauhinweise Damit der Blockschlossriegel während der Montage ein - und ausgefahren werden kann, wird die braune Ader an +12 V und die weiße Ader an Masse angeschlossen. Die grüne und die gelbe Ader bleiben unbeschaltet. So wird das Schließen des Blockschlossriegels ohne Anschluss an die Auswerteeinheit ermöglicht.
Montage-Anschluss-Anleitung IK2-Blockschloss Blockschlossumbau Stulp- Befestigungs- Dornmaßverlängerung schraube Das IK-Blockschloss kann mit dem jeweiligen Umrüstsatz von Dornmaß 25 mm auf die Dornmaße 35 mm, 50 mm, 55 mm, 65 mm, 80 mm und 100 mm erweitert werden. Riegel- abdeckplatte Dornmaß Art.-Nr. 022114.01 Dornmaß...
Page 8
Montage-Anschluss-Anleitung IK2-Blockschloss Blockschlossmontage hinter einer Mehrfachverriegelung (bei Holztüren) In Verbindung mit dem Sonderstulp 16 mm (Art.Nr. 022121 ) kann ein IK-Blockschloss problemlos in einer Tür mit Mehrfachverriegelung eingesetzt werden. Siehe hierzu auch Broschüre "Elektrische Installation von gefahrenmeldetechnischen Anlagen" (P03061-15-000-XX). 20 mm bewegliche Schubstange Blockschloss...
Montage-Anschluss-Anleitung IK2-Blockschloss Anschlusshinweise / Erdung Bitte beachten: Unter der Voraussetzung, dass der Betriebsspannungsverlust von 0,5 V DC (siehe Zeichnung) nicht überschritten wird, kann das IDENT-KEY Blockschloss bis zu 5 m von der Auswerteeinheit entfernt montiert werden. max. 5 m IDENT-KEY...
Montage-Anschluss-Anleitung IK2-Blockschloss Technische Daten Betriebsnennspannung 12 V DC Betriebsspannungsbereich 10,0 V bis 15 V DC Stromaufnahme bei Nennspannung 6 mA zusätzliche Stromaufnahme der Blockspule 120 mA Lagerungstemperaturbereich -30 °C bis +60 °C Betriebstemperaturbereich -25 °C bis +60 °C Einbaulage beliebig Schutzklasse nach DIN 40 050 IP 30 Umweltklasse gemäß...
The IDENT-KEY block lock serves as switching element for arming/disarming of intrusion detection systems in combination with the IDENT-KEY rosettes (022167 / 022169). The block lock can be connected to the evaluation units 022160.10 / 022160.20 / 022164 / 022200 or 022200.10.
Make sure that there is enough space at the bottom side of the opening for the profile semi- cylinder for laying the flat-band cable of the rosette. Do not forget to drill the holes for the IDENT-KEY rosette. 3. Lay out block lock connecting cable in the door leaf.
Page 17
Mounting and Connection Instructions IK2 block lock Door leaf IDENT-KEY section block lock Drill holes for rosette fixture (use the drilling pattern) IDENT-KEY rosette Connecting cable Attention! Make sure that there is sufficient space at this point for the rosette connecting cable! 5.
Page 18
Mounting and Connection Instructions IK2 block lock Installation instructions To allow the block lock bolt to be moved in and out during the installation the brown wire has to be connected to the +12 V and the white wire to ground. The green and the yellow wire remain unconnected.
Page 19
Mounting and Connection Instructions IK2 block lock Conversion of the block lock Face plate fixing screw Bolt length extension The IK-block lock bolt can be extended with the corresponding kit from 25 mm to bolt lengths of 35 mm, 50 mm, 55 mm, 65 mm, 80 mm and 100 mm. Bolt length Item-No.
Page 20
Mounting and Connection Instructions IK2 block lock Block lock mounting behind a multiple locking device (wooden doors) In combination with the special face plate 16 mm (Item-No. 022121 ) an IK-block lock can be mounted easily on a door with multiple locking. Also see the folder "Electrical installation of hazard detection systems"...
Connection instructions / grounding Please note: Provided that the operating voltage drop does not exceed 0.5 V DC (see drawing) the IDENT-KEY block lock can be mounted at a maximum distance of 5 m to the evaluation unit. max. 5 m...
Mounting and Connection Instructions IK2 block lock Technical data Rated operating voltage 12 V DC Operating voltage range 10.0 V to 15 V DC Current consumption at rated voltage 6 mA Additional current consumption of the block coil 120 mA Storage temperature range -30 °C to +60 °C Operating temperature range...
Mounting and Connection Instructions IK2 block lock The program Item-No. 022220 IDENT-KEY block lock IK2 Item-No. 022167 IDENT-KEY rosette Color: black Item-No. 022169 IDENT-KEY rosette Color: greywhite (similar to RAL 9002) Item-No. 022180 Distance piece 2.5 mm (between door leaf and rosette) Color: black Item-No.