Available languages
Available languages
Quick Links
Before you begin - Read these instructions completely
and carefully. IMPORTANT – OBSERVE ALL
GOVERNING CODES AND ORDINANCES. Note to
Installer – Be sure to leave these instructions with the
Consumer. Note to Consumer – Keep these instructions
with your Owner's Manual for future reference.
Tools Needed
• 5/16" nut driver
• Pliers
• Slotted screwdriver
Parts included in bag with Sub-Base
Type A
10 required
Type D
2 mounting clips for
metal case
Type B
Type C
2 required
2 required
4 nuts
Type E
2 mounting clips for
molded case
Chaseway and
cover
Installation Instructions
for your new
RAK204U
RAK204D15C
RAK204D20C
RAK204D30C
RAK204E15C
RAK204E20C
RAK204E30C
Sub-Base
Important Notes
• This unit must be properly grounded.
• Read this instruction before installing the sub-base to the
molded or metal case.
CAUTION
The sub-base should be assembled to the
case before securing the case in the wall.
CAUTION
Electrical power must be disconnected
before installing the sub-base.
Electrical Requirements :
1. Electrical wiring may enter the sub-base through
any of the knockout holes provided in the sub-base
bottom or rear.
2. Refer to the unit nameplate for branch circuit
requirements.
3. All wiring should be done in accordance with the local
electrical codes and regulations.
4. Not approved for aluminum wire application.
5. If electrical wiring is placed in or against the sub-
base enclosure, the sub-base must be grounded.
Grounding holes have been provided in the back
surface of the enclosure. See diagram. Green
grounding screws and securing nuts are included.
Kit Number
Description
RAK204U
NON-ELECTRICAL SUB-BASE
RAK204E15C
265 V
RAK204E20C
265 V
RAK204E30C
265 V
RAK204D15C
230/208 V
RAK204D20C
230/208 V
RAK204D30C
230/208 V
RAK4002D
JUNCTION BOX
31-5000401 Rev. 0 03-19 GEA
15 A
20 A
30 A
15 A
20 A
30 A
Related Manuals for GE RAK204U
Summary of Contents for GE RAK204U
- Page 1 Installation Instructions for your new RAK204U RAK204D15C RAK204D20C RAK204D30C Before you begin - Read these instructions completely RAK204E15C and carefully. IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to RAK204E20C Installer – Be sure to leave these instructions with the RAK204E30C Consumer.
-
Page 2: Installation Instructions
Installation Instructions Metal Case (RAB71*) Install ground screw from the rear and secure from the inside of the sub-base using a nut. Secure branch circuit (or other) Green ground ground wire using a second nut. screw (type C) 6” 6” Mounting Type B screws clip for... - Page 3 Installation Instructions INSTALLATION FOR 230/208V MODELS 4. Remove the rectangular knockout at the bottom of the junction box. Remove the rectangular knockout at the Follow the installation instruction with the Power Supply right end of the sub-base. Kit if RAK4002D Junction Box Kit to install junction box and connect to the unit wiring.
- Page 4 5. Remove the rectangular knockout at the bottom of the junction box. Remove the rectangular knockout at the right end of the sub-base. Screw Junction Box Base Rectangular knockout Chaseway knockout Front View A Quality Product of GE Appliances...
- Page 5 Instructions d’installation pour votre nouveau socle RAK204U RAK204D15C Avant de commencer – Lisez ces instructions RAK204D20C RAK204D30C attentivement et en totalité. RAK204E15C IMPORTANT – OBSERVEZ TOUS LES CODES ET RÈGLEMENTS EN VIGUEUR. RAK204E20C Remarque à l’installateur – Assurez-vous de remettre ces RAK204E30C instructions au consommateur.
- Page 6 Gaine métallique (RAB71*) Posez la vis de mise à la terre depuis l’arrière et fixez depuis l’intérieur du socle à l’aide d’un écrou. Fixez le fil de terre du Vis de terre verte circuit de dérivation (ou autre) à (type C) l’aide du deuxième écrou.
-
Page 7: Instructions D'installation
Instructions d’installation INSTALLATION des modèles 230/208 V : 4. Enlevez la débouchure rectangulaire dans le bas de la boîte de jonction. Enlevez la débouchure rectangulaire à Suivez les instructions d’installation de la trousse d’alimenta- tion électrique ou de la boîte de jonction RAK4002D pour in- Couvercle de la Junction box staller la boîte de jonction et connecter le câblage de l’appareil. - Page 8 Enlevez la débouchure rectangulaire à manuel d’utilisation du Zoneline. Languette Screw de vis Base de Junction Box la boîte de Base jonction Débouchure Rectangular rectangulaire knockout Débouchure pour chemin de câble Chaseway knockout Vue de face Front View Un produit de qualité GE Appliances...