Cisco Catalyst 2960-X Series Hardware Manual
Hide thumbs
Also See for Catalyst 2960-X Series:
- Security configuration manual (498 pages) ,
- Command reference manual (135 pages) ,
- Hardware installation manual (34 pages)
Quick Links
See also:
Configuration Manual
Catalyst 2960-X and 2960-XR Switch Hardware Guide
The Catalyst 2960-X and Catalyst 2960-XRfamily of switches are Ethernet switches to
which you can connect devices such as Cisco IP Phones, Cisco Wireless Access Points,
workstations, and other network devices such as servers, routers, and other switches.
Some models of the switches support stacking through the Cisco FlexStack-Plus
technology. Unless otherwise noted, the term switch refers to a standalone switch and to a
switch stack.
This chapter contains these topics:
Switch Models
Front Panel
Rear Panel
Management Options
Network Configurations
Switch Models
Switch
Model
Catalyst
LAN Base
2960X-
48FPD-L
Catalyst
LAN Base
2960X-
1
48LPD-L
Catalyst
LAN Base
2960X-
1
24PD-L
Catalyst
LAN Base
2960X-
1
48TD-L
Supported
Software
Image
48 10/100/1000 Power over Ethernet Plus
(PoE+) ports (PoE budget of 740 W) and 2
small form-factor pluggable (SFP)+ module
slots.
48 10/100/1000 PoE+ ports (PoE budget of 370
W) and 2 SFP+ module slots.
24 10/100/1000 PoE+ ports (PoE budget of 370
W) and 2 SFP+ module slots.
48 10/100/1000 ports and 2 SFP+ module slots.
Description
Related Manuals for Cisco Catalyst 2960-X Series
Summary of Contents for Cisco Catalyst 2960-X Series
- Page 1 Catalyst 2960-X and 2960-XR Switch Hardware Guide The Catalyst 2960-X and Catalyst 2960-XRfamily of switches are Ethernet switches to which you can connect devices such as Cisco IP Phones, Cisco Wireless Access Points, workstations, and other network devices such as servers, routers, and other switches.
- Page 2 24 10/100/1000 (8 PoE- with PoE budget of 110 2960X- W) ports, fanless, 2 10/100/1000BaseT copper 24PSQ-L uplinks, and 2 SFP module slots. Table 1 Catalyst 2960-X Switch Models and Descriptions Support Cisco FlexStack-Plus technology. SFP+ = 10-Gigabit uplink. SFP = 1-Gigabit uplink.
- Page 3 Switch Model Supported Description Software Image Catalyst IP Lite 48 10/100/1000 PoE+ ports (PoE budget of 2960XR- 740 W) 2 SFP+ module slots, 1025-W 48FPD-I power supply. Catalyst IP Lite 48 10/100/1000 PoE+ ports (PoE budget of 2960XR- 370 W) 2 SFP+ module slots, 640-W power 48LPD-I supply.
-
Page 4: Front Panel
Front Panel This section describes the front panel components: 24 or 48 downlink ports of one of these types: 10/100/1000 10/100/1000 PoE+ SFP ports USB Type A connectors USB mini-Type B (console) port Ethernet management port ... - Page 5 PoE and PoE+ Ports The ports provide PoE+ support for devices compliant with IEEE 802.3af, IEEE 802.3at, and ePoE and also provide Cisco prestandard PoE support for Cisco IP Phones and Cisco Aironet Access Points. The maximum switch power output is either 740 W or 370 W, depending on the switch model.
- Page 6 The USB console interface speeds are the same as the RJ-45 console interface speeds. If you use the USB mini-Type B console port, the Cisco Windows USB device driver must be installed on any PC connected to the console port (for operation with Microsoft...
- Page 7 The USB Type A port provides access to external USB flash devices (also known as thumb drives or USB keys). The port supports Cisco USB flash drives with capacities from 128 MB to 8 GB (USB devices with port densities of 128 MB, 256 MB, 1 GB, 4 GB, and 8 GB are supported).
- Page 8 LEDs You can use the switch LEDs to monitor switch activity and its performance. Figure 4. Switch LEDs and Mode Button for the Catalyst 2960-X Switch. This figure shows the switch LEDs and the Mode button that you use to select a port mode. 1 RPS LED PoE LED 2 SPEED LED...
- Page 9 RPS = redundant power system—only on switch models that support RPS. Only on switch models that support PoE. Only on switch models that support stacking.Figure 5. Switch LEDs and Mode Button for the Catalyst 2960-XR Switch. This figure shows the switch LEDs and the Mode button that you use to select a port mode.
- Page 10 7 STACK LED Port LEDs Only on switch models that support PoE. Only on switch models that support stacking. System LED RPS LED IRPS LED Master LED Port LEDs and Modes STACK LED Console LEDs ...
- Page 11 IRPS LED The IRPS LED is only available on Catalyst 2960-XR switches. Color RPS Status Second power supply is not present. Green Both power supplies are present and operating. Amber The second power supply is present, but the input is not connected.
- Page 12 Noncompliant cabling or powered devices can cause a PoE port fault. Use only standard- compliant cabling to connect Cisco prestandard IP Phones and wireless access points or IEEE 802.3af-compliant devices. You must remove any cable or device that causes a PoE fault.
- Page 13 Port Mode Port LED Meaning Color Port is operating at 10 Mb/s. Green Port is operating at 100 Mb/s. Blinking Port is operating at 1000 Mb/s. green SFP module ports Port is operating at 10 Mb/s. Green Port is operating at 100 Mb/s. Blinking Port is operating at 1000 Mb/s.
- Page 14 stack members. The other port LEDs are off because there are no more members in the stack. Figure 6. STACK LED. This figure shows the LEDs on the first switch, which is stack member number 1. Stack member 1 Stack member 3 Stack member 2 When you select the STACK LED, the respective STACK LEDs are green when the stack ports (on the switch rear panel) are up, and the respective Stack LEDs are amber when the...
-
Page 15: Rear Panel
Color Description USB console port Green USB console port is active. When this LED is on, the RJ-45 console port LED is off. The port is not active, and the RJ-45 console port is active. Table 9 RJ-45 and USB Console LEDs Ethernet Management Port LED Color Description... - Page 16 1 FlexStack-Plus module slot and cover 3 RPS Connector 2 Fan Exhaust 4 AC power connector The rear panel of the Catalyst 2960-XR switches have a FlexStack-Plus module slot and power supply module slots. Figure 8. Catalyst 2960-XR Switch Rear Panel 1 FlexStack-Plus module slot and 4 PS OK LED cover...
- Page 17 The Cisco RPS 2300 (model PWR-RPS2300) supports the Catalyst 2960-X switch. Note RPS is not supported on the Catalyst 2960-X 24PSQ-L switches. Warning Attach only the following Cisco RPS model to the RPS receptacle: RPS2300. Statement 370 Connect the switch and the redundant power system to different AC power sources.
- Page 18 System 2300 Hardware Installation Guide on Cisco.com at this URL: http:// www.cisco.com/en/US/products/ps7148/prod_installation_guides_list.html The Cisco RPS 2300 has two output levels: –52 V and 12 V with a total maximum output power of 2300 W. All supported and connected switches can simultaneously communicate with the RPS 2300.
-
Page 19: Management Options
Cisco Network Assistant is a PC-based network management GUI application for LANs of small and medium-sized businesses. You can use the GUI to configure and manage switch clusters or standalone switches. Cisco Network Assistant is available at no cost and can be downloaded from this URL: http://www.cisco.com/en/US/products/ps5931/index.html... -
Page 20: Network Configurations
Cisco Prime Infrastructure combines the wireless functionality of Cisco Prime Network Control System (NCS) and the wired functionality of Cisco Prime LAN Management Solution (LMS), with application performance monitoring and troubleshooting capabilities of Cisco Prime Assurance Manager. For more information, see the Cisco Prime Infrastructure documentation on Cisco.com.