Related Manuals for Softing Data Flow commModule MBP
Summary of Contents for Softing Data Flow commModule MBP
- Page 1 Hardware Manual commModule MBP Version: EN-022018-1.00 © Softing Industrial Automation GmbH...
- Page 2 Softing Industrial Automation GmbH Richard-Reitzner-Allee 6 85540 Haar / Germany http://industrial.softing.com + 49 89 4 56 56-340 + 49 89 4 56 56-488 [email protected] [email protected] The latest version of this manual is available in the Softing download area at: http://industrial.softing.com/en/downloads.html...
-
Page 3: Table Of Contents
ESD handling precautions ....................... 17 Packaging and labeling ....................... 17 Special conditions for safe use ..................18 Chapter 7 Galvanic isolation ....................... 18 Safety block diagram ....................... 18 Installation ....................... 19 Isolation and creepage distances ....................... 19 © Softing Industrial Automation GmbH... - Page 4 Table of Contents Label ....................... 20 Maintenance and spare parts ....................... 20 CE Compliance ..................21 Chapter 8 ATEX EC type examination certificate ....................... 22 IECEx Certificate of Conformity ....................... 27 Declaration of Conformity ....................... 35 © Softing Industrial Automation GmbH...
-
Page 5: Introduction
For further details about the commModule MBP and the configuration workflow of the firmware see the following document: commScript PD Customization Guide Conventions used The following conventions are used throughout Softing customer documentation: CAUTION This symbol indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. -
Page 6: Commmodule Mbp
Operating conditions for use in hazardous environment Diagram The block diagram below shows the design of the commModule MBP: Intended use This product has been designed to be integrated as a system component by a qualified hardware engineer. © Softing Industrial Automation GmbH... -
Page 7: Interface
Ground GPIO_PE2 GPIO For future use GPIO_PE5 GPIO, AI For future use GPIO_PE7 GPIO, AI For future use GPIO_PE1 GPIO For future use PROT_SEL_P27 / TCK Protocol Select: FF/PA, Programming interface Programming interface Ground Ground © Softing Industrial Automation GmbH... - Page 8 * AI = Analog Input, AO = Analog Output, DI = CMOS Digital Input, DO = CMOS Digital Output, GPIO = General Purpose CMOS Digital Input/Output, PO = Power Output, DBG = Programmer Interface, FB = Fieldbus, PD Pulldown, PU Pullup © Softing Industrial Automation GmbH...
-
Page 9: Pullups And Pulldowns
The memory blocks are reserved for the firmware. They must not be modified as this will invalidate the software license and damage the commModule MBP. Only programming project files provided by Softing shall be used to reprogram the module. Fault Disconnect Equipment External fault disconnect equipment (FDE) can be optionally added using the assigned FDE pins. -
Page 10: Electrical Specifications
When both power outputs are used, the available power budget is between 70 and 90mW. The slew rate is controlled. The rise time is 1.43ms. The output current is not limited on the commModule MBP. © Softing Industrial Automation GmbH... - Page 11 Rated current adjusted in software to In = 10mA up to 26mA. Powered from Fieldbus 9V to 32V (non hazardous location). Use in hazardous locations: Limitation on fieldbus power supply applies for different use cases. See also Operating conditions for use in hazardous environment © Softing Industrial Automation GmbH...
-
Page 12: Environmental Specifications
Additional requirements apply for the design of the host PCB. For further information see the ATEX EC type examination certificate MTBF calculation MTBF calculated according to SN29500: @40°C: 3.655.879 hours @70°C: 1.142.849 hours Conditions: Standard SN29500, continuous operation © Softing Industrial Automation GmbH... -
Page 13: Certifications
The commModule MBP is ROHS compliant. ATEX / IECEx: IECEx IBE 17.0038U Ex ia IIC Ga [Ex ia Da] IIIC IBExU17ATEX1135 U II 1G Ex ia IIC Ga II (1) D [Ex ia Da] IIC © Softing Industrial Automation GmbH... -
Page 14: Mechanical Specification
The weight of a potted variant (commModule MBP#STD) is approximately 15 gram. The weight of the non- potted variant (commModule MBP#STD_NOP) is 8 gram. Module dimensions The dimensions below are shown in millimeters. Bottom view © Softing Industrial Automation GmbH... -
Page 15: Host Pcb Layout
Routing under the CommModule MBP Note The host PCB footprint must not contain any exposed copper under the module except the pads interfacing the CommModule MBP to avoid any contact with traces on the module. © Softing Industrial Automation GmbH... - Page 16 Ensure a clearance of 2mm between fieldbus on Pin 37 – 39 to all other pins and Pin 37 to Pin 39. Solderpaste Note The recommended stencil thickness is 0.12 to 0.15mm. Note The schematic library and PCB library for the Altium Designer can be download here: © Softing Industrial Automation GmbH...
-
Page 17: Mounting Process
The PCB is made of FR4 and has a NiAu surface finish. We strongly recommend that commModule MBP modules are not soldered more than once after shipping by Softing. The soldering of the communication module is compliant with RoHS directive 2011/65. -
Page 18: Special Conditions For Safe Use
MBP as a bare module. Galvanic isolation The circuits of the commModule MBP have no galvanic isolation. All signals are galvanically connected together. Safety block diagram The following block diagram shows the commModule MBP: © Softing Industrial Automation GmbH... -
Page 19: Installation
FIELDBUS_N with level of protection 30V according to table 5 in IEC 60079-0 Pin 38, 39 FIELDBUS_P, FIELDBUS_N No requirement on creepage distances between these signals. Clearance and creepage distance to all other signals © Softing Industrial Automation GmbH... -
Page 20: Label
The commModule MBP is marked with a label similar to the example below. Maintenance and spare parts The device does not require any maintenance. In case of malfunctioning or failure, disassemble the device or the affected part and return this device to Softing for repair. © Softing Industrial Automation GmbH... -
Page 21: Chapter 8 Ce Compliance
Chapter 8 - CE Compliance CE Compliance This device complies with the following EC directives: EC directive 2014/30/EU "EMC directive” EC directive 2014/34/EU "ATEX" EC directive 2011/65/EU "RoHS" © Softing Industrial Automation GmbH... -
Page 22: Atex Ec Type Examination Certificate
MBP - Hardware Manual ATEX EC type examination certificate © Softing Industrial Automation GmbH... - Page 23 Chapter 8 - CE Compliance © Softing Industrial Automation GmbH...
- Page 24 MBP - Hardware Manual © Softing Industrial Automation GmbH...
- Page 25 Chapter 8 - CE Compliance © Softing Industrial Automation GmbH...
- Page 26 MBP - Hardware Manual © Softing Industrial Automation GmbH...
-
Page 27: Iecex Certificate Of Conformity
Chapter 8 - CE Compliance IECEx Certificate of Conformity © Softing Industrial Automation GmbH... - Page 28 MBP - Hardware Manual © Softing Industrial Automation GmbH...
- Page 29 Chapter 8 - CE Compliance © Softing Industrial Automation GmbH...
- Page 30 MBP - Hardware Manual © Softing Industrial Automation GmbH...
- Page 31 Chapter 8 - CE Compliance © Softing Industrial Automation GmbH...
- Page 32 MBP - Hardware Manual © Softing Industrial Automation GmbH...
- Page 33 Chapter 8 - CE Compliance © Softing Industrial Automation GmbH...
- Page 34 MBP - Hardware Manual © Softing Industrial Automation GmbH...
-
Page 35: Declaration Of Conformity
Chapter 8 - CE Compliance Declaration of Conformity © Softing Industrial Automation GmbH... - Page 36 Softing Industrial Automation GmbH Richard-Reitzner-Allee 6 Tel: + 49 89 45 656-340 85540 Haar / Germany Fax: + 49 89 45 656-488 http://industrial.softing.com [email protected]...