4-174-240-11 (1)
Notes on Use
Before Use
If you find condensation when you open the package, turn on the power after
leaving it for about 60 minutes.
Data and security
Network Camera
You should keep in mind that the images or audio you are monitoring may be
protected by privacy and other legal rights, and the responsibility for making
sure you are complying with applicable laws is yours alone.
Access to the images and audio is protected only by a user name and the
password you set up. No further authentication is provided nor should you
Installation Manual
presume that any other protective filtering is done by the service. Since
Before operating the unit, please read this manual thoroughly and
the service is Internet-based, there is a risk that the image or audio you are
retain it for future reference.
monitoring can be viewed or used by a third-party via the network.
SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU
OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR
EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY
DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.
Security configuration is essential for wireless LAN. Should a problem
occur without setting security, or due to the limitation of the wireless LAN
specifications, SONY shall not be liable for any damage, loss of recorded data
or restoration thereof.
Always make a test recording, and verify that it was recorded successfully.
SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT
LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE
OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR
SNC-CH140
ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.
Always verify that the unit is operating properly before use. SONY WILL NOT
BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY
OTHER REASON WHATSOEVER.
2009 Sony Corporation
Printed in China
If you lose data by using this unit, SONY accepts no responsibility for
restoration of the data.
Personal information
Owner’s Record
The images taken by the system using this device can identify individuals
and thus they fall under “personal information” stipulated in the “Act on
The model and serial numbers are located on the top. Record these numbers
the Protection of Personal Information”. Please handle the video data
in the spaces provided below.
appropriately according to law.
Refer to these numbers whenever you call upon your Sony dealer regarding
Information recorded using this product may also be “personal information”.
this product.
Upon disposal, transfer, repair, or any other occasion where this product or
Model No.
Serial No.
storage media is passed on to a third party, practice due care in its handling.
Operating or storage location
WARNING
Avoid operating or storing the camera in the following locations.
Extremely hot or cold places (Operating temperature:
10°C to +50°C [14°F to
–
To reduce a risk of fire or electric shock, do not expose
122°F])
this product to rain or moisture.
Exposed to direct sunlight for a long time, or close to heating equipment (e.g.,
near heaters)
Close to sources of strong magnetism
To avoid electrical shock, do not open the cabinet. Refer
Close to sources of powerful electromagnetic radiation, such as radios or TV
servicing to qualified personnel only.
transmitters
Locations subject to strong vibration or shock
WARNING
Ventilation
This installation should be made by a qualified service person and should
conform to all local codes.
To prevent heat buildup, do not block air circulation around the camera.
WARNING
Transportation
A readily accessible disconnect device shall be incorporated in the building
Always turn off the power when carrying.
installation wiring.
When transporting the camera, repack it as originally packed at the factory or
in materials of equal quality.
WARNING (for Installers only)
Cleaning
Instructions for installing the equipment on the ceiling or the wall:
After the installation, ensure the connection is capable of supporting at least
Use a blower to remove dust from the lens.
a force of 50 Newtons (N) downwards.
Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn
stains can be removed using a soft cloth dampened with a small quantity of
CAUTION for LAN port
detergent solution, then wipe dry.
For safety reason, do not connect the LAN port to any network devices that
Do not use volatile solvents such as alcohol, benzene or thinners as they may
might have excessive voltage.
damage the surface finishes.
The LAN port of this unit is to be connected only to the devices whose
Note on laser beams
power feeding meets the requirements for SELV (Safety Extra Low Voltage)
and complies with Limited Power Source according to IEC 60950-1 Second
Laser beams may damage image sensors. You are cautioned that the surface of image
sensors should not be exposed to laser beam radiation in an environment where a laser
Edition.
beam device is used.
Power Supply
Phenomena Specific to Image Sensors
Caution for U.S.A. and Canada
The SNC-CH140 operates on 24V AC or 12V DC.
The following phenomena that may occur in images are specific to image
The SNC-CH140 automatically detects the power.
sensors. They do not indicate a malfunction.
In the USA, this product shall be powered by a UL listed Class 2 Power Supply
White flecks
Only.
Although the image sensors are produced with high-precision technologies, fine
In Canada, this product shall be powered by a CSA Certified Class 2 Power
white flecks may be generated on the screen in rare cases, caused by cosmic rays,
Supply Only.
etc.
This is related to the principle of image sensors and is not a malfunction.
Caution for other countries
The white flecks especially tend to be seen in the following cases:
The SNC-CH140 operates on 24V AC or 12V DC.
- when operating at a high environmental temperature
The SNC-CH140 automatically detects the power.
- when you have raised the gain (sensitivity)
Use a power supply rated 24 V AC or 12 V DC which meets the requirements
- when using the slow shutter
for SELV (Safety Extra Low Voltage) and complies with Limited Power Source
according to IEC 60950-1 Second Edition.
Aliasing
For customers in the U.S.A.
When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
You are cautioned that any changes or modifications not expressly approved
in this manual could void your authority to operate this equipment.
All interface cables used to connect peripherals must be shielded in order to
comply with the limits for a digital device pursuant to Subpart B or Part 15 of
FCC Rules.
For customers in Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
For the customers in Europe
The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-
ku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to the addresses given in
separate service or guarantee documents.
For the customers in Europe, Australia and New Zealand
WARNING
This is a Class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
In the case that interference should occur, consult your nearest authorized
Sony service facility.
This apparatus shall not be used in the residential area.
ATTENTION
The electromagnetic fields at specific frequencies may influence the picture
of the unit.