1. Manuals
  2. Brands
  3. Sony Manuals
  4. DVR
  5. SIR-3400H
  6. Instruction manual

Sony SIR-3400H Instruction Manual

Hi-speed hdd data recorder, precision analog unit / wide band analog unit
Hide thumbs
Table of Contents

Quick Links

Hi-speed HDD Data Recorder
SIR-3400H
Precision Analog Unit / Wide Band Analog Unit
SIR-3032i / SIR-3032W
Read all the instructions in the manual carefully before use and strictly follow them.
Keep the manual for future references.
Instruction Manual
Table of Contents
loading

Related Manuals for Sony SIR-3400H

Summary of Contents for Sony SIR-3400H

  • Page 1 Hi-speed HDD Data Recorder SIR-3400H Precision Analog Unit / Wide Band Analog Unit SIR-3032i / SIR-3032W Read all the instructions in the manual carefully before use and strictly follow them. Keep the manual for future references. Instruction Manual...
  • Page 2 For AC power-driven products to meet EN 61000-6-2/2001, the following operational conditions must be satisfied. 1. Input and output signal cable length SIR-3400H / SIR-3032i / SIR-3032W : 30 m or less : 10 m or less : 30 m or less...
  • Page 3 Durch Ihren Beitrag zum korrekten Entsorgen dieses Produkts schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. Umwelt und Gesundheit werden durch falsches Entsorgen gefährdet. Materialrecycling hilft, den Verbrauch von Rohstoffen zu verringern. Weitere Informationen über das Recycling dieses Produkts erhalten Sie auf der Webseite von Sony Manufacturing Systems Europe: http://www.sonymanufacturing.com/environment...
  • Page 4 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 5: Safety Precautions

    Safety Precautions Sony Manufacturing Systems Corporation products are designed in full consideration of safety. However, improper handling during operation or installation is dangerous and may lead to fire, electric shock or other accidents resulting in serious injury or death. In addition, these actions may also worsen machine performance.
  • Page 6 . Replace only with specified type and rated fuse. CAUTION . Disconnect the power cord from the unit if it is not in use. . Disconnect the power cord before replaceing fuse. Make sure to ground the POWER cable firmly. Earth SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 7 Power Switch When turning off the unit completely, first confirm that the ACCESS lamp is out and then turn off the POWER switch on the rear of unit. SIR-3400H / SIR-3032i / SIR-3032W Remarks Displayed until the internal temperature is...
  • Page 8 TEDS data, or IEPE mode, which doesn’t acquire TEDS data, can be selected. The standby lamp and other lamps on the front panel go out. (The unit is completely shut down.) SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 9: Table Of Contents

    Overwriting Data ... 2-2 2-6. ID Block ... 2-3 3. Names and Functions of Parts ... 3-1 3-1. SIR-3400H (Recording unit) ... 3-1 3-1-1. Front Panel ... 3-1 3-1-2. Rear Panel ... 3-11 3-1-3. Side Panels ... 3-15 3-2. SIR-3032i/W (Measuring Unit) ... 3-16 3-2-1.
  • Page 10 12-8. Setting the Transmission Format ... 12-8 12-9. Recording Memo ... 12-8 12-10. Setting the Output Level ... 12-10 12-11. Setting the Test Signal ... 12-11 12-12. Mark Settings ... 12-11 12-13. Panel Lock ... 12-11 SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 11 16-2. Start ID Search ... 16-2 16-2-1. Searching at the Next Recording Start Position ... 16-2 16-2-2. Searching at the Current Recording Start Position ... 16-3 16-3. Mark Search ... 16-3 16-4. Address Search ... 16-3 SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 12 21. Attaching the Rack Mount Adaptor ... 21-1 21-1. Before Use ... 21-1 21-2. Attachment Procedure for Rack Mount Adaptor ... 21-1 22. Specifications ... 22-1 22-1. Specifications (SIR-3400H) ... 22-1 22-1-1. Cartridges ... 22-1 22-1-2. Voice Annotation Channel ... 22-1 22-1-3. Monitor Out ... 22-1 22-1-4.

  • Page 13: Overview

    By combining with a measuring unit, the SIR-3000 series can be used to build the optimum system for measurement subjects. Support for 32 ch x 20 kHz is provided by combining the minimum configuration of the SIR-3400H and SIR-3032i. Replacing the measuring unit with the SIR-3032W enables wideband recording at 32 ch x 80 kHz.
  • Page 14 By employing the high-speed data transfer interface (option), digital data can be transferred to a computer in real-time during recording or playing back. (The transfer speed depends on the computer performance.) Control Functions The unit can be controlled from the local (front panel) or from the host computer via Ethernet. SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 15 Dimensions of 449 (W) x 88 (H) x 305 (D) mm (recording unit only, without projections) and a weight of approximately 10.5 kg for the recording unit and 7.5 kg for the measuring unit give the SIR-3000 a design with superior compactness and portability. SIR-3400H / SIR-3032i / SIR-3032W Power switch on No power...
  • Page 16 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 17: Data Format And Basic Operations

    2. Data Format and Basic Operations 2-1. Data Format Data recorded to HDDs by the SIR-3400H is based on the FAT32 logical format. However, at the application level the data is of the SIR dedicated format. This is outlined below.

  • Page 18: Initialization Of Recording Media (Formatting)

    2-3. Initialization of Recording Media (Formatting) When a different format (such as one where data has been written by a computer) or unformatted SMH cartridge is loaded in the SIR-3400H, the Format Error is displayed on the LCD screen. Implement the HDD formatting.

  • Page 19: Id Block

    ID block length is one Record. This is approximately 42 ms at 4x speed, 170 ms at normal speed (1x), and 2.7 seconds at 1/16x speed. Thus, recording at 1/16x speed cannot be stopped within 2.7 seconds. SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 20 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 21: Names And Functions Of Parts

    These slits are used to take in air to cool the inside of the recording unit. To prevent the inside of the recording unit from overheating, do not cover the ventilation slits. SIR-3400H / SIR-3032i / SIR-3032W LCD screen Setting keys...
  • Page 22 Press this key alone to select the E-E mode. Press this key together with the FWD key to record data. qs PAUSE key Used when performing a recording pause or playback pause. ACCESS2: Recording media 2 SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 23 When the playback signal source of the speakers or earphones are set to voice annotation When the playback signal source of the speakers or earphones are set to analog data signals SIR-3400H / SIR-3032i / SIR-3032W 3. Names and Functions of Parts...
  • Page 24 Value recorded on recording media Display Value set in recording unit Value recorded on recording media Display ADDRESS, REMAIN, and S-TIME values set in recording unit ADDRESS, REMAIN, and R-TIME values recorded on recording media SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 25 This area displays the recording media capacity that is being used. wf Function key command display area This area displays the function key commands during setting. (The function key commands vary depending on the setting option.) SIR-3400H / SIR-3032i / SIR-3032W 3. Names and Functions of Parts...
  • Page 26 When the key is pressed by itself When the setting key is pressed after the SHIFT key : in SHIFT mode eh ed RANGE OFFSET INPUT SEARCH MEMO OUT/TSG MRK1 : No additional comment MRK2 Yes/No Yes/No SIR-3400H / SIR-3032i / SIR-3032W SHIFT...
  • Page 27 F1 to F4 keys The functions displayed on the current LCD screen are assigned to F1 to F4 keys. The assigned functions vary depending on the setting item. SIR-3400H / SIR-3032i / SIR-3032W 3. Names and Functions of Parts In SHIFT mode...
  • Page 28 MIC jack Insert the supplied microphone plug here. The lamp at the bottom right lights according to the sound input. rs MONITOR The channel of the measuring unit displayed on the LCD screen is output. SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 29 To eject the HDD, first set to STOP mode, and then check that the HDD access lamp is turned off. The HDD can be damaged if you unlock the HDD while the HDD access lamp is turned on. SIR-3400H / SIR-3032i / SIR-3032W Locked...
  • Page 30 The recording unit settings are stores in a CF-type flash memory. The stored settings are used to make the various settings of the recording unit. 3-10 Error recovery method . RAID rebuild . HDD initialization . HDD replacement . HDD initialization . HDD replacement SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 31: Rear Panel

    . To prevent the inside of the recording unit from overheating, do not block the air outlet. . Leave a space of at least 100 mm between the rear side of the recording unit and any other object. SIR-3400H / SIR-3032i / SIR-3032W Aux output / TRIGER input block...
  • Page 32 Rated voltage 250 V Size 5 ø20L Be sure to disconnect the DC power cord before replacing the fuse. 7 Ground terminal This is a ground terminal for the frame ground. 3-12 5 6 7 SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 33 Used to synchronously operate multiple recording units. qd TO HOST connector Used to control the recording unit from a host computer. qf TO EXPMAIN1/TO EXPMAIN2 connector Used to connect the measuring units. SIR-3400H / SIR-3032i / SIR-3032W 3. Names and Functions of Parts 3-13...
  • Page 34 3. Names and Functions of Parts Option Slots qg Option slot Insert optional boards here. 3-14 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 35: Side Panels

    . Do not place hot objects on the right and left side of the recording unit. . Leave a space of at least 50 mm between the right and left sides of the recording unit and any other object. SIR-3400H / SIR-3032i / SIR-3032W 3. Names and Functions of Parts 3-15...

  • Page 36: Sir-3032I/W (Measuring Unit)

    These slits are used to take in air to cool the inside of the measuring unit. To prevent the measuring unit from overheating, do not block the ventilation slits. 3-16 Analog input connectors Indicator block MONITOR SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 37 TEDS mode, which acquires the TEDS data, or IEPE mode, which doesn’t acquire TEDS data, can be selected. 5 S/D selector switch Sets the transmission format in the analog input block. S : Single-ended D : Differential SIR-3400H / SIR-3032i / SIR-3032W 3. Names and Functions of Parts MONITOR 3-17...
  • Page 38 If the setting button is not pressed within three seconds after the EXP No. display is displayed, it changes back to the monitor channel display. qa Monitor output Outputs the channel number displayed on the indicator from the analog channel output in the measuring unit. 3-18 MONITOR SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 39: Rear Panel

    When there are multiple measuring units, the channels are put in order starting from the smallest EXP Channel assignments for two 32-channel measuring units EXP No. 1 : Channels 1 to 32 EXP No. 2 : Channels 33 to 64 SIR-3400H / SIR-3032i / SIR-3032W Analog output connectors EXP No. Reserve...
  • Page 40 Rated current 10 A Rated voltage 250 V Size 5 ø20L Be sure to disconnect the DC power cord before replacing the fuse. 9 Ground terminal This is a ground terminal for the frame ground. 3-20 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 41: Side Panels

    . Do not place hot objects on the right and left side of the measuring unit. . Leave a space of at least 50 mm between the right and left sides of the measuring unit and any other object. SIR-3400H / SIR-3032i / SIR-3032W 3. Names and Functions of Parts 3-21...
  • Page 42 3-22 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 43: Preparations

    . Make sure that spike noise is not included when taking AC power from an inverter, etc. . The internal backup battery is charged whenever the POWER switch is set to ON regardless of whether the unit is in standby mode. SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 44 Connect the AC power cord (supplied) to the AC IN connector. Supply the power. When set to 100/120 V : 90 to 132 V AC When set to 220/240 V : 198 to 250 V AC SIR-3400H SIR-3032i/W SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 45: Dc Power Supply

    Connect the 12 V DC power supply (allowable 11 to 30 V) The polarities of the DC power cord are red: positive and black: negative. The connector pin assignment is Pin 1: positive, Pin 2: negative and Pin3: frame GND. SIR-3400H / SIR-3032i / SIR-3032W 4. Preparations SIR-3400H...

  • Page 46: Internal Backup Battery

    . 24 V power is supplied to BNC cable when the recorder is set in E-E, REC-PAUSE or REC mode during IEPE input (IEPE or TEDS). Be sure to check the input format when connect a signal source to the INPUT connector. Oscilloscope, etc. Signal source MONITOR SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 47: Cartridges

    Check that the ACCESS lamp on the front panel is turned off. Press the Standby key. Set the POWER switch on the rear panel to OFF. Cartridges compatible with the SIR-3400H SMH cartridge 4-3-2. Loading a Cartridge Press the Standby key to turn on the power.

  • Page 48: Ejecting The Cartridge

    Pull out the SMH cartridge while pulling the handle forward. Close the front panel. Set the right and left lock knobs on the front panel to LOCK, and check that the front panel is closed properly. SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 49: Diagnostics

    IEPE input (IEPE or TEDS). Be sure to check the input format when connect a signal source to the INPUT connector. In order to stabilize the DC bias of the IEPE sensor, make a recording after warming up the unit sufficiently with E-E mode. SIR-3400H / SIR-3032i / SIR-3032W 4. Preparations...

  • Page 50: Source And Record

    In the record mode, press the F3 key to sequentially change the contents displayed as follows. Address Amount of recording (± h/m/s) media remaining Source time (h/m) (y/m/d) Record time (y/m/d) (h/m) Source time (h/m/s) Record time (h/m/s) SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 51: Description Of Transport Mode

    Real-time clock This searches the specified real-time clock value written on the search recording media (controlled by Telnet). Manual search This performs 16x-speed fast-forwarding or fast-rewind. SIR-3400H / SIR-3032i / SIR-3032W Lit lamp (over key) STOP REC, FWD REC, FWD,...

  • Page 52: Operation Transition Diagram

    Skip the start of the next ID number the current ID number STOP STOP (Stop) REC + FWD REC + FWD PAUSE REC + PAUSE STOP PAUSE Manual search (16x-speed fast-forward) Hold down (Fast-forward) STOP STOP SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 53: Transport Mode Transition Table

    FWD-PAUSE STOP — STOP — STOP — STOP — SEARCH STOP — SIR-3400H / SIR-3032i / SIR-3032W REC + + + + + REC + + + + + PAUSE PAUSE REC-PAUSE REC FWD-PAUSE REC-PAUSE REC REC-PAUSE — — REC-PAUSE —...
  • Page 54 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 55: Setting And Check Items

    Changing the AC voltage 100/120 V or 200/240 V Save of setting values/ — Recall of setting values SIR-3400H / SIR-3032i / SIR-3032W Remarks LCD screen Key Telnet Panel For acoustic measurement and other situations where silence is needed Based on changes in the operating environment 7-2-2...
  • Page 56 O (Front) After recording Remarks LCD screen Key Telnet Panel O (Front) Reference 12-13 14-2 14-3 14-4 14-5 14-6 14-7 Reference 13-4 14-8 17-2 17-2 17-2 17-2 17-2 17-2 17-2 Reference 12-5 12-6 12-7 12-10 17-2 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 57: Lcd Screen Configuration

    (Checking the Recoding Media Contents) Time (Changing to the Address, Amount of Recording Media Remaining, or Time Display) PK-CLR (Clearing the Peak Indicator and Over Indicator) SIR-3400H / SIR-3032i / SIR-3032W Main Fan Control (Fan Control On/Off) f / F Dew Sense...
  • Page 58 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 59: Basic Settings (Main Screen)

    7-2-3. Synchronization Mode * The screen of “Main” – “Function” – “Display” – “Network” – “Clock” can be switched with the F1/F2 keys. * Press the F4 key to return to the Measurement screen. SIR-3400H / SIR-3032i / SIR-3032W On/Off Master/Subordinate...

  • Page 60: Settings

    Medium High Recording unit status Remarks Detecting the condensation The remaining time for detecting the condensation is displayed Condensation was detected Displayed during warmup operation Dissipating condensation Displays the remaining time until condensation is dissipated SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 61: Synchronized Master/Subordinate Operation (Sync-Mode)

    When using a synchronized connection, one recording unit must be set as the Master, and the other recording units must be set as the Subordinate. Set the rest of recording units other than one for Master to Subordinate. SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 62 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 63: Function Setup (Function Screen)

    8-2-6. IRIG-B Timecode * The screen of “Main” – “Function” – “Display” – “Network” – “Clock” can be switched with the F1/F2 keys. * Press the F4 key to return to the Measurement screen. SIR-3400H / SIR-3032i / SIR-3032W On/Off Single/Multi...

  • Page 64: Selecting The Frequency Type (Freq-Type)

    If it is not needed, press the FWD key while holding down the REC key again to start overwriting. If a portion of the data is overwritten, the data after the current recording point can no longer be played. The recording cannot be overwritten. SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 65: Selecting The Trigger Mode (Trigger Mode)

    When set to Off, the internal clock is not calibrated with the IRIG-B time code. Factory setting: On * For the setting procedure, see “8-1. Setting Procedure (for Function Screen)”. SIR-3400H / SIR-3032i / SIR-3032W 8. Function Setup (Function Screen)
  • Page 66 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 67: Display Settings (Display Screen)

    The peak indicator is held at the maximum level until PK-CLR (F4) is pressed or until entering the E-E, REC-PAUSE, or REC-FWD modes from STOP mode. SIR-3400H / SIR-3032i / SIR-3032W Realtime/Hold %/dB 0 to 10...

  • Page 68: Switching The Bar Meter Scale (Bar Meter Scale)

    The LCD brightness can be adjusted in one of eleven levels. Decibel indicator (unidirectional) Red (over indicator) 2 dB State when 0 dB Yellow is exceeded 0 dB Green _6 dB Bluish green _20 dB Light blue _∞ dB White SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 69: Network Settings (Network Screen)

    * By pressing F3 (Apply) key, the changed IP address and the changed subnet mask are set. When escaped from the Global Setup Menu without setting, the changed value is not set. * Press the F4 key to return to the Measurement screen. SIR-3400H / SIR-3032i / SIR-3032W 10-1...
  • Page 70 10-2 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 71: Clock Setting (Clock Screen)

    * By pressing the F3 (Apply) key, the changed time is set. When escaped from the “Global Setup Menu” without setting, the changed value is not set. * Press the F4 key to return to the Measurement screen. SIR-3400H / SIR-3032i / SIR-3032W 11-1...
  • Page 72 11-2 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 73: Operation Settings (Using Setting Key)

    2 Speed MByte/s Press the SPD/BCM key. The recording/playback speed is set. SIR-3400H / SIR-3032i / SIR-3032W (Mode: REC) (Mode: REC) (Mode: STOP) x x x x x 1 x x x x x 1/2...

  • Page 74: Setting The Number Of Recording Channels

    Use the f / F key to select the number of channels. Setting value: 32/64/128 No. of measuring units Press the SPD/BCM key. The number of recording channels is set. 12-2 Max. no. of channels SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 75: Setting The Input Range

    When not in setting mode, the f, F, g, and G keys can be used to change the monitor channel. f / F key : Every 16 channels g / G key : Every channel SIR-3400H / SIR-3032i / SIR-3032W (Modes: STOP, E-E, REC-PAUSE, and REC) (See [12-7. Setting the Input Format]): 0.5 V...

  • Page 76: Setting The Auto Range

    0.55 V to 0.22 V to 0.11 to 5.5 V 2.2 V 1.1 V 0.55 V ± 5 ± 2 ± 1 ± 0.5 (See [12-7. Setting the Input Format]): Less than 0.22 V 0.11 V ± 0.2 ± 0.1 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 77: Setting The Input Dc Offset

    When not in setting mode, the f, F, g, and G keys can be used to change the monitor channel. f / F key : Every 16 channels g / G key : Every channel SIR-3400H / SIR-3032i / SIR-3032W (Modes: STOP, E-E, REC-PAUSE, and REC) _ _ _ _ _ 100 0 ...

  • Page 78: Setting Input Dc Offset Automatically

    DC component is calculated. Until the OFFSET key is pressed again, the peak value detection is continued. After three or more seconds have elapsed, press the OFFSET key. The DC input offset value is set for all channels. 12-6 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 79: Setting The Input Format

    When not in setting mode, the f, F, g, and G keys can be used to change the monitor channel. f / F key : Every 16 channels g / G key : Every channel SIR-3400H / SIR-3032i / SIR-3032W (Modes: STOP) Contents When using the sensor without support of TEDS or the TEDS data is not acquired, set it.

  • Page 80: Setting The Transmission Format

    The lamp at the top left of the key turns on, and the Record Memo indicator appears in the setting value display area to indicate that the memo can be edited. 12-8 Supported input format Direct input, IEPE input Direct input SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 81 . Pressing the F2 key deletes the character at the cursor position. The characters after the cursor position move back to fill in the deleted space. . If the cursor is at the end of the text, the cursor position moves forward each time the F2 key is pressed. SIR-3400H / SIR-3032i / SIR-3032W Disabled abcABC...

  • Page 82: Setting The Output Level

    When not in setting mode, the f, F, g, and G keys can be used to change the monitor channel. f / F key : Every 16 channels g / G key : Every channel 12-10 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 83: Setting The Test Signal

    Hold down the SHIFT key for at least two seconds in the Panel Lock state. This cancels Panel Lock, and the PNL LOK lamp turns off. SIR-3400H / SIR-3032i / SIR-3032W (Modes: E-E, REC-PAUSE, and REC) 12. Operation Settings (Using Setting key)
  • Page 84 12-12 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 85: Other Settings

    Turn the VOL knob on the recording unit rear panel. Be careful that you do not listen to earphones (sold separately) at a high volume for extended periods of time. SIR-3400H / SIR-3032i / SIR-3032W Display ADDRESS → REMAIN → S-TIME (Y, M, D) → S-TIME (H, M, S) →...

  • Page 86: Changing The Ac Voltage

    Use the AC voltage selector switch on the rear panel of the respective unit to change the voltage. Move the switch to the selected voltage side. Left side : 100/120 V (allowable 90 to 132 V) Right side : 220/240 V (allowable 198 to 250 V) 13-2 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 87: Execution Of Function/Checking

    (See section 6-1 for the factory settings.) Press the F1 key in the Measurement screen. The Utility screen is displayed. Use the f / F key to select “Save/Recall Setup”. Press the F1 key. The Save/Recall Setup screen is displayed. SIR-3400H / SIR-3032i / SIR-3032W 14-1...
  • Page 88 Sets the channel settings to the settings of recording with current address Sets the channel settings to the factory settings (See section 6-1-2) Sets the basic settings (See section 7.) to the factory settings (See section 6-1) SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 89: Copying Mark1/Mark2 (Copy)

    Mark1 The copy operation is performed. The copy operation will not be performed when the F2 key is pressed unless Mark1 and Mark2 are within the same ID. SIR-3400H / SIR-3032i / SIR-3032W : F2 key : F3 key Mark2 14.

  • Page 90: Formatting The Hard Disk Drive (Format)

    A dialog box is displayed for confirming the formatting operation. Press the FWD key while holding down the REC key. Formatting is performed. Press the F4 key (cancel). Once formatting is started, it cannot be cancelled. 14-4 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 91: Repairing Recording Media Discrepancies (Raid Rebuild)

    If you cancel while the repair operation is in progress, the data in the receiving HDD will be incomplete and cannot be read. To exit “RAID Rebuild”, press the F4 key. SIR-3400H / SIR-3032i / SIR-3032W 14. Execution of Function/Checking 14-5...

  • Page 92: Executing Calibration (Calibration)

    Press the F4 key. Calibration is stopped at the point where the frequency band changes. If calibration is stopped before completion, turn the power off and then on again before using. 14-6 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 93: Bar Meter Auto Adjustment (Barmeter Auto Adjustment)

    Use the f / F keys to select “Barmeter Auto Adjustment”. Press the F1 key. A dialog box is displayed for confirming execution. Press the FWD key while holding down the REC key. This executes bar meter auto adjustment. SIR-3400H / SIR-3032i / SIR-3032W 14. Execution of Function/Checking 14-7...

  • Page 94: Executing Diagnostics (Diagnostics)

    Use the F key to select “Diagnostics”. Press the F1 key. The diagnostics are performed. This takes about one minute. Press the F4 key. If an error occurs, an error code will be displayed (see section 18-2). 14-8 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 95: Checking The Recording Media Contents (Toc Viewer)

    Use the f / F key to select ID. Press the G key. The INDEX for selected ID are deployed and displays on the screen. To close the detailed list, press the g key. SIR-3400H / SIR-3032i / SIR-3032W 14. Execution of Function/Checking 14-9...

  • Page 96: Toc Screen Elements

    This is the ID recording conditions (Number of channels: Analog input A, Digital input D). 5 Speed This is the recording speed. 6 Length The address value at recording is displayed. 7 Date This is the recording start date and time. 14-10 (CAUTION 1) (CAUTION 2) SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 97: Data Recording/Playback

    In addition, a start ID is also attached each time recording starts to allow start ID search. The INDEX number increments each time the INDEX/ID key is pressed during recording. The INDEX numbers can be used to find specific locations. SIR-3400H / SIR-3032i / SIR-3032W MONITOR 15-1...
  • Page 98 15. Data Recording/Playback Stopping Recording Press the STOP key. This stops recording, writes a TOC (and EOD) to that position, and then the EOD lights. 15-2 MONITOR Earphone Microphone Oscilloscope, etc. Signal source SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 99: Data Playback

    . Noise may be generated if data between recording blocks is played back. . It takes max. 2 seconds from the start of playback when to set input setting the same as the settings recorded on the recording media. SIR-3400H / SIR-3032i / SIR-3032W Analysis equipment MONITOR 15.

  • Page 100: Recording And Playback Voice Annotations

    Connect the earphone (sold separately) to the PHONE jack on the front panel. 15-4 Bandwidth 0.2 to 76.8 kHz 0.2 to 38.4 kHz 0.2 to 19.2 kHz 0.2 to 9.6 kHz 0.2 to 4.8 kHz 0.2 to 2.4 kHz 0.2 to 1.2 kHz Microphone MONITOR Earphone SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 101: Recording Voice Annotations

    . When the speed during recording and playback differ, the pitch (signal frequency) of voice annotations differs from the pitch at recording. . The existence of voice annotations can be checked by the light of MIC lamp while the VOL knob is in the minimum position. SIR-3400H / SIR-3032i / SIR-3032W 15. Data Recording/Playback 15-5...

  • Page 102: Recording And Playback Aux Digital Data

    Approx. 6 µs Approx. 12 µs Approx. 25 µs Approx. 50 µs Approx. 100 µs : Minimum hold time (See Table 15-4-1.) Tr, Tf : Level transition time (1 µs or less regardless of recording speed) SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 103: Connecting The Aux Digital Data

    AUX-1 (DIGITAL) OUT connector on the rear panel. Also, when a playback signal is detected, existence of the input signal during recording is displayed in the status display area of the LCD screen. 15-7 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 104: Recording And Playback Aux Analog Data

    IRIG time code reader. When the IRIG timecode is set to Off, it is not handled as an IRIG-B timecode signal. 15-8 : Amplitude modulation code (AC code) : 1 kHz : ± 1 to ± 10 Vpk SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 105 For the R-TIME information in the recording media position display area during playback, the recording unit's real-time clock value (xxYxxMxxD/xxHxxMxxS) recorded on the recording media is displayed. This value corresponds to the IRIG time recorded on the recording media. SIR-3400H / SIR-3032i / SIR-3032W 15. Data Recording/Playback 15-9...

  • Page 106: Recording And Playback Aux Analog Data

    Playing Back AUX Analog Data Signal When a recording media recorded with an AUX analog data signal is played back, the AUX analog data signal is output from the AUX-2 (IRIG-B) OUT connector on the rear panel. 15-10 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 107: Trigger Recording

    Use a BNC cable (sold separately) to connect the TRIG REC IN connector on the rear panel and the trigger signal. Signal source . It the ADDRESS duration is less than 2 seconds, the next signal may not start up. . The input voltage level should be TTL level. SIR-3400H / SIR-3032i / SIR-3032W 15. Data Recording/Playback 15-11...

  • Page 108: Playback Of The Pre-Trigger Data

    Data is recorded immediately after being triggered. * See section 8 for pre-trigger recording. 15-6-3. Playback of the Pre-trigger Data The pre-trigger data is played back with the ADDRESS “-000H00M00S”. 15-12 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 109: Search

    The lamp display during ID/INDEX number search and Mark search modes are shown below. Search operation Lamp SEARCH SEARCH key pressed Searching Blinking FOUND (ends normally) NOT FOUND (target not found) SIR-3400H / SIR-3032i / SIR-3032W Host computer INDEX/ID Mark1, Mark2 Blinking Blinking Lamp of selected mode lit 16-1...

  • Page 110: Id/Index Number Search

    16-2-1. Searching at the Next Recording Start Position Press the SEARCH key in STOP mode, and then press the FF key. This skips to and stops at the start point of the next recording from the current position. 16-2 (see 14-8) SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 111: Searching At The Current Recording Start Position

    MRK1 key MRK2 key 16-4. Address Search This function searches target by the address value. It is controlled from the host computer by Telnet (See section 17). 16-3 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 112: Real-Time Clock Search

    Reverse search While pressing the FWD key, press the REW key. The contents rewind while the keys are held down (16x-speed rewind). * When the REW key is released, the mode changes to FWD. 16-4 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 113: Control By Telnet

    TCP/IP (Telnet) connection HOST IP address : 192.168.1.100 (default setting) Port no. : 23 Login : xxxx Password : sms After entering this information, the commands can be executed. Type “quit” to disconnect from Telnet. SIR-3400H / SIR-3032i / SIR-3032W 17-1...

  • Page 114: Command Overview

    Recording/playback speed setting SYN : Selecting synchronous playback TIM : Real-time clock setting TRG : Trigger setting TRM : Terminator selection TSG : Test signal selection UTL : Utility mode setting 17-2 Comments Only during stop SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 115: Command

    TOC? TOC data readout TRG? Trigger setting status TRM? Terminator selection status (returned strings) TSG? Test signal selection status UTL? Utility mode setting readout VOL? Recording media volume readout SIR-3400H / SIR-3032i / SIR-3032W 17. Control by Telnet Comments 17-3...

  • Page 116: Command Format

    : 0=RSV, 1=Formatting start 0=OFF 1=1 ch (Async) 2=2 ch (Async) 3=4 ch (Async) 4=8 ch (Async) 5=RSV 6=RSV 7=RSV 9=RSV A=1 ch (Sync) B=2 ch (Sync) C=4 ch (Sync) D=8 ch (Sync) E=RSV F=RSV SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 117 4=Measuring unit 3 5=Measuring unit 3 6=Measuring unit 4 7=Measuring unit 4 Related command : MON? SIR-3400H / SIR-3032i / SIR-3032W 1 to 16 CH 17 to 32 CH 33 to 48 CH 49 to 64 CH 65 to 80 CH...
  • Page 118 113 to 128 CH 1 to 16 CH 17 to 32 CH 33 to 48 CH 49 to 64 CH 65 to 80 CH 81 to 96 CH 97 to 112 CH 113 to 128 CH SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 119: Syn

    <1> : 0=CR + LF, 1=CR, 2=LF This sets the break code for replies from the recording unit. The default is (CR + LF). Related command : TRM? SIR-3400H / SIR-3032i / SIR-3032W : 001 to 999 or 000 : 0=Forward, 1=Backward — Target : ID=100 17.
  • Page 120 In case of <1> and <3>, when one is set to “1”, be sue to set the other to “0”. Ex.) OK <1> : 1, <3> : 0 NG <1> : 1, <3> : 1 Related command : UTL? When not selecting the mode, it all sets to ZERO. 17-8 SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 121 Returned format CAL : <1> <1> : 0=Calibration finished normally 1=Calibration finished abnormally 2 to 7=Value other than 01 Related command : CAL SIR-3400H / SIR-3032i / SIR-3032W : mm (minutes) : ss (seconds) : mm (minutes) : ss (seconds) 0=RSV...
  • Page 122 F=RSV Related command : CHA CFG? Unit configuration Command format CFG?/[ ] Returned format CFG : <1><2>...<7> <1> : 0=SIR-1000, 1=SIR-1000W, 2=SIR-1000i, 3=SIR-3400H, 4=SIR-3100T <2> : Option slot 1 type 0=None 1=RSV 2=RSV 3=RSV 4=RSV 5=RSV <3> : Option slot 2 type...
  • Page 123 <4> : Input format for CH2 <18> : Input format for CH16 Related command : INP SIR-3400H / SIR-3032i / SIR-3032W 0= Other than below (after power-on or STOP command execution, etc.) 1= Recording media formatting underway 2= Recording media formatting finished normally (becomes “0”...
  • Page 124 7F=MAX and overload (OVR) 00=MIN : CH 1 MAX data (2-digit hexadecimal) : CH 1 MIN data (2-digit hexadecimal) 7F=MAX and overload (OVR), +100 % = 60 80=MIN and overload (OVR), _100 % = A0 SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 125 PNL : <1> <1> : 0=Panel lock canceled, 1=Panel lock set Related command : PNL SIR-3400H / SIR-3032i / SIR-3032W : CH 1 DC offset (2-digit hexadecimal 2’s complement display) : CH 2 DC offset (2-digit hexadecimal 2’s complement display) 17.
  • Page 126 SPD? <1>/[ ] <1> : 0=Recording unit setting value, 1=Recording media data Returned format SPD : <1> <1> : 0=1 x, 1=1/2 x, 2=1/4 x, 3=1/8 x, 4=1/16 x, A=x2, B=x4, F=EXT Related command : SPD 17-14 SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 127 <1> : 0=Recording unit setting value, 1=Recording media data Returned format TIM : <1><2>...<12> <1><2> : Year (last 2 digits) <3><4><5><6> : Month and date <7><8><9><10><11><12> : Hours, minutes and seconds Related command : TIM SIR-3400H / SIR-3032i / SIR-3032W 17. Control by Telnet 17-15...
  • Page 128 Related command : TSG 17-16 1=Start ID 1=2 ch, 2=4 ch, 3=8 ch, 4=16 ch, 5=32 ch, 6=64 ch, 7=96 ch, 8=128 ch 1=1 ch, 2=2 ch, 3=4 ch, 4=8 ch 1=Pre-trigger recording 1=Write error SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 129 <21><22> : Last recorded year (last 2 digits) <23><24><25><26> : Last recorded month and date <27><28><29><30><31><32> : Last recorded hours, minutes and seconds Related command : TOC? SIR-3400H / SIR-3032i / SIR-3032W 2: Rebuild NG executed 2: Delete NG executed 17.
  • Page 130 17-18 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 131: Errors And Error Messages

    (retry) of the relevant section was repeated. As a result, the FIFO memory became empty, and the output data is interrupted. * During this retry operation, the data SIR-3400H / SIR-3032i / SIR-3032W Recording unit status Detecting the condensation Condensation was detected Dissipating condensation remaining in the FIFO memory is output until the correct data is read.

  • Page 132: Error Code

    Error occurred between DPR board and DR board Error occurred between DPR board and IF board Error occurred between DR board and IF board Sync Setting error/cable error Sync No target/sync playback data Sync Recording/playback error Sync target is recording alone SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 133: Remedies For Operation Errors

    3. Hold down the standby switch for two seconds again. If operation is still not restored, set the POWER switch to OFF, unplug the power cable, and then contact service engineer. SIR-3400H / SIR-3032i / SIR-3032W The condensation data is not set No available space in HDD...
  • Page 134 18-4 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 135: Connecting The Recording Unit And Measuring Unit

    Spring washers (ø4) Hexagonal socket head bolts (M4: black) 16 L wrench (for M4) Remove the four bottom feet from the bottom of the recording unit. Leave the bottom feet on the measuring unit. SIR-3400H / SIR-3032i / SIR-3032W Quantity 19-1...
  • Page 136 Use the 4 fixtures supplied with the measuring unit (black), 16 washers (ø4), 16 spring washers (ø4: black), 16 hexagonal socket head bolts (M4: black), and L wrench (for M4) to attach the measuring unit and recording unit. 19-2 Recording unit SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 137: Cable Connections

    19-2. Cable Connections 64 Channel Configuration Ground connection Ground connection Ground connection 128 Channel Configuration Ground connection SIR-3400H / SIR-3032i / SIR-3032W Ether Net Extension cable (supplied) Computer Ether Net SIR-3400H SIR-3032i/W SIF-3004 (sold separately) SIR-3032i/W SIR-3032i/W SIR-3032i/W Extension cable (supplied) 19.
  • Page 138 19-4 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 139: Installing The Shock Mount Adaptor

    Shock mount adaptor packing contents Name Shock mount adaptor L wrench (for M4) L wrench (for M8) Hexagonal socket head bolts (M4) Spring washers (ø4) Bolts with hexagonal holes (M8) Spring washers (ø8) Instruction manual SIR-3400H / SIR-3032i / SIR-3032W Quantity 20-1...

  • Page 140: Installation Procedure For Shock Mount Adaptor

    Reference: Installation hole dimensions and pitch 493.6 mm Remove the legs from the bottom of unit. 20-2 Shock mount adaptor ø9 hole Recording unit * In case of the measuring unit, the removal procedure is the same. SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 141 Use the supplied hexagonal socket head bolts (M4), spring washers (ø4), and L wrench (for M4) to secure the unit to the shock mount adaptor. Recording unit Measuring unit SIR-3400H / SIR-3032i / SIR-3032W For use of a single recording unit alone Recording unit Shock mount adaptor 20.
  • Page 142 20-4 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 143: Attaching The Rack Mount Adaptor

    The cover of the unit is removed before securing the rack mount adaptor, and so there is a danger of electrical shock or other accident. Attachment should not be performed by the customer. If attachment is required, please contact Sony Manufacturing Systems Corporation. Rack mount adaptor packing contents...
  • Page 144 (black) from each side cover (right and left), and then take off the right and left side covers. Left side cover Lift up one side of the top cover and one side of the bottom cover. 21-2 Right side cover Top cover Bottom cover SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 145 Use the eight M4 x 10 (silver) screws removed in step 4 to attach the two rack mount adapters and two corner blocks. Rack mount adaptor SIR-3400H / SIR-3032i / SIR-3032W 21. Attaching the Rack Mount Adaptor Corner handle Rack mount adaptor...
  • Page 146 21. Attaching the Rack Mount Adaptor Attach the top cover and side cover removed in steps 1 to 3 by performing steps 1 to 3 in reverse order. 21-4 SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 147: Specifications (Sir-3400H)

    : 1x BNC (Single-ended) Level : TTL Impedance : 10 kZ : ± 10 Vpk Withstand voltage Output Connectors : 1x BNC (Single-ended) Level : TTL Impedance : 50 Z Applicable load : 1 kZ or more SIR-3400H / SIR-3032i / SIR-3032W 22-1...

  • Page 148: Aux Analog Channel (Aux-2, Irig-B Channel)

    : 11 to 30 V : 13.5 to 5 A : AC > DC > internal backup battery : 449 (W) x 88 (H) x 305 (D) mm (Excluding projections) : Approx. 10.5 kg (Including two SMH cartridges) SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 149: Operating Environment

    When using a plug adaptor (3-pin to 2-pin) for the AC power cord, be sure to connect the green wire to earth. SIR-3400H / SIR-3032i / SIR-3032W (Be sure to warm up the recorder if it is operated under 5 dC.)

  • Page 150: Specifications (Sir-3032I/W)

    86 dB or more 86 dB or more 84 dB or less 84 dB or less ±10 Vpk ±1.0 dB, ±1.0 dB, 80 dB or more 80 dB or more 74 dB or less 74 dB or less SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 151: Operation System

    Power source : POWER Monitor : MONITOR CH is displayed : LED on INPUT : IEPE input SIR-3400H / SIR-3032i / SIR-3032W BNC x 32 Direct Single-ended, Differential — DC, AC (0.5 Hz) ± 0.1, ± 0.2, ± 0.5, ± 1, ± 2, ± 5, ± 10 Vpk ±...

  • Page 152: Power Supply System

    : 660 to 1060 hPa (Equivalent to the altitude of about 3000 m to _400 m) : Horizontal (front panel facing forwards) : 14.7 m/s 5 Hz to 200 Hz (horizontal position) : 392 m/s , 11 ms (while stored) : II : II SIR-3400H / SIR-3032i / SIR-3032W...

  • Page 153: Supplied Accessories

    L wrench (for M4) Extension cable When using a plug adaptor (3-pin to 2-pin) for the AC power cord, be sure to connect the green wire to earth. SIR-3400H / SIR-3032i / SIR-3032W : x1 : x1 ( for 100/120 V models only)
  • Page 154 22-8 SIR-3400H / SIR-3032i / SIR-3032W...
  • Page 155 したがって、当社の許可なしに無断で複写したり、説明内 容（操作、保守など）と異なる目的で本マニュアルを使用 することを禁止します。 The material contained in this manual consists of information that is the property of Sony Manufacturing Systems Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Manufacturing Systems Corporation expressly...

  • Page 156: Sir-3400H / Sir-3032I / Sir-3032W

    Sony Manufacturing Systems Corporation 1-10 Kiyoku-cho, Kuki-shi, Saitama 346-0035 Japan http://www.sonysms.co.jp/ SIR-3400H / SIR-3032i / SIR-3032W 2-672-654-12 Printed in Japan ©2006 Sony Manufacturing Systems Corporation 2006.9...

This manual is also suitable for:

Sir-3032iSir-3032w

Table of Contents