1. INTRODUCTION 17MB100 main board is driven by MStar SOC. This IC is a single chip iDTV solution that supports channel decoding, MPEG decoding, and media-center functionality enabled by a high performance AV CODEC and CPU. This IC also supports 4K2K (UHD). Key features includes, ...
Page 4
Features Worldwide hybrid TV tuner o Analog TV: NTSC, PAL/SECAM o Digital TV: ATSC/QAM, DVBT2/T/C2/C, ISDB-T/C, DTMB o 42-1002 MHz frequency range Industry-leading margin to A/74, NorDig, DTG, ARIB, EN55020, OpenCable™ Lowest BOM for a hybrid TV tuner o No balun at RF input o Integrated tracking filters requiring no external inductors or SAW filters o Increased ESD protection on 6 pins...
Absolute Maximum Ratings Recommended Operating Conditions 3. AUDIO AMPLIFIER STAGES A. MAIN AMPLIFIER (TAS5719) General Description The TAS5717/TAS5719 is a 10-W/15-W, efficient,digital audio-power amplifier for driving stereo bridge- tied speakers. One serial data input allows processing of up to two discrete audio channels and seamless integration to most digital audio processors and MPEG decoders.
Page 8
Features • Audio Input/Output o TAS5717 Supports 2×10 W and TAS5719 Supports 2×15 W Output o Wide PVDD Range, From 4.5 V to 26 V o Efficient Class-D Operation Eliminates Need for Heatsinks o Requires Only 3.3 V and PVDD o One Serial Audio Input (Two Audio Channels) o I2C Address Selection via PIN (Chip Select) o Supports 8-kHz to 48-kHz Sample Rate (LJ/RJ/I2S)
Page 9
Pin descriptions and functions: Figure: TAS5719 Pin descriptions...
Table: Recommended Operating Conditions B. HEAD-PHONE AMPLIFIER STAGE Head-phone is a SoC (single on chip) configuration in mainboard, Design scheme is shown in figure 3. Figure: Head-phone...
C. SUBWOOFER AMPLIFIER STAGE PREAMPLIFIER (DRV632) Description The DRV632 is a 2-VRMS pop-free stereo line driver designed to allow the removal of the output dc- blocking capacitors for reduced component count and cost. The device is ideal for single-supply electronics where size and cost are critical design parameters.
Page 13
Figure: PW package Table: Pin functions Table: Recommended operating conditions SUB WOOFER MAIN AMPLIFIER (TAS5727) Description The TAS5727 is a 25-W, efficient, digital-audio power amplifier for driving stereo bridge-tied speakers.One serial data input allows processing of up to two discrete audio processors and MPEG decoders. The device accepts a wide range of input data and data rates.
Page 14
Features Audio Input/Output o 25 W Into an 8-Ω Load From a 20-V Supply o Wide PVDD Range, From 8V to 26V o Supports BTL Configuration with 4- Ω Load o Efficient Class-D Operation Elminates Need for Heatsinks o One serial Audio Input (Two Audio Channels) C Address Selection Pin (Chip Select) o Single Output Filter PBTL Support o Supports 441-kHz to 48-kHz Sample Rate (LJ/RJ/I...
4. POWER STAGE Figure: Power socket and options Power socket is used for taking voltages which are 12V, 5V and 24V(VDD_Audio). These voltages are produced in power board. Also socket is used for giving dimming, backlight and standby signals with power board.
Page 18
24V(VDD_Audio) goes directly to the audio side, through power socket other incoming voltages from power card are converted several voltages, shown in figure 8. List of the components are: TPS54528 TPS54328 TPS54821 TPS51363 APL5910 LM1117 TPS54528 General Description...
Page 19
Networking Home Terminal Digital Set Top Box(STB) Table: Recommended operating conditions Figure: Pin Description Table: Pin functions TPS54328 General Description The TPS54328 is an adaptive on-time D-CAP2 mode synchronous buck converter.The TPS54328 enables system designers to complete the suite of various end-equipment power bus regulators with a cost effective, low component count, low standby current solution.
Page 20
series resistance (ESR)output capacitors, such as POSCAP or SP-CAP, and ultra-low ESR ceramic capacitors. The device operates from 4.5-V to 18-V VIN input. The output voltage can be programmed between 0.76 V and 7 V. The device also features an adjustable soft start time. The TPS54328 is available in the 8-pin DDA and 10-pin DRC packages, and is designed to operate over the ambient temperature range of -40C to 85C.
Page 21
Table: Pin functions Table: Pin description TPS51363 General Description The TPS51363 is a high-voltage input, synchronous converter with integrated FET, based on D-CAP2™ control topology, which enables fast transient response and supports both POSCAP and all MLCC output capacitors. TI proprietary FET technology combined with TI leading-edge package technology provides the highest density solution for single-output power rail such as VCCIO and VDDQ for DDR notebook memory, or any point-of-load (POL) in wide application.
Page 22
Features Input Voltage Range: 3 V to 22 V Output Voltage Range: 0.6 V to 2 V 8-A or 10-A Integrated FET Converter Fewest External Components Soft-Start Time Programmable by External Capacitor Switching Frequency: 400 kHz and 800 kHz ...
Page 24
TPS54821 General Description The TPS54821 in thermally enhanced 3.5 mm x 3.5 mm QFN package is a full featured 17 V, 8 A synchronous step down converter which is optimized for small designs through high efficiency and integrating the high-side and low-side MOSFETs. Further space savings are achieved through current mode control, which reduces component count, and by selecting a high switching frequency, reducing the inductor's footprint.
Page 26
Table: Pin functions MP2234 General Description The MP2234 is a high frequency synchronous rectified step-down switch mode converter with built in internal power MOSFETs. It offers a very compact solution to achieve 3A continuous output current over a wide input supply range with excellent load and line regulation. The MP2234 has synchronous mode operation for higher efficiency over output current load range.
Page 27
Thermal Shutdown Output Adjustable from 0.8V Available in an 8-pin TSOT-23 package Figure: Pin description Table: Pin functions...
Page 28
APL5910 General Description The APL5910 is a 1A ultra low dropout linear regulator. The IC needs two supply voltages, one is a control voltage (VCNTL) for the control circuitry, the other is a main supply voltage (VIN) for power conversion, to reduce power dissipation and provide extremely low dropout voltage.
Page 29
Table: Recommended operating conditions Table: Pin description LM1117 General Description The LM1117 is a series of low dropout voltage regulators with a dropout of 1.2V at 800mA of load current. It has the same pin-out as National Semiconductor’s industry standard LM317. The LM1117 is available in an adjustable version, which can set the output voltage from 1.25V to 13.8V with only two external resistors.
Page 30
Current Limiting and Thermal Protection Output Current 800mA Line Regulation 0.2% (Max) Load Regulation 0.4% (Max) Temperature Range: o LM1117 0˚C to 125˚C o LM1117I −40˚C to 125˚C Applications 2.85V Model for SCSI-2 Active Termination ...
7. 1GB DDR3 SDRAM HYNIX H5TQ1G63DFR Description The H5TQ1G63DFR-xxx series are a 1,073,741,824-bit CMOS Double Data Rate III (DDR3) Synchronous DRAM, ideally suited for the main memory applications which requires large memory density and high bandwidth. Hynix 1Gb DDR3 SDRAMs offer fully synchronous operations referenced to both rising and falling edges of the clock.
Page 43
Table: Recommended operating conditions 8. 2GB DDR3 SDRAM HYNİX H5TQ2G63DFR Description The H5TQ2G63DFR is a 2,147,483,648-bit CMOS Double Data Rate III (DDR3) Synchronos DRAM, ideally suited fort he main memory applications which requires large memory density and high bandwidth. SK Hynix 2Gb DDR3 SDRAMs offer fully synchronous operations referenced to both rising and falling edges of the clock.
Page 44
TDQS (Terminal Data Stobe) supported (x8 only) Write Levelization supported 8 bit pre-fetch Table: Absolute Maximum DC Ratings Table: Recommended operating conditions 9. 32GBİT (4G X 8 BİT) NAND FLASH MEMORY HYNIX H26M31001HPR Key Features eMMC4.5 compatible (Backward compatible to eMMC4.41) ...
Page 45
o Health(Smart) report Description SK hynix e-NAND consists of NAND flash and MMC controller.e-NAND has the built-in intelligent controller which manages interface protocols, wear leveling, bad block management, garbage collection, and ECC. e-NAND protects the data contents from the host sudden power off failure.e-NAND is compatible with JEDEC standard eMMC4.5 specification.
10. 16M-BIT [16M X 1] CMOS SERIAL FLASH EEPROM MX25L1602 MSTAR SPI FLASH Key Features ■ HIGH DENSITY NAND FLASH MEMORIES General 16,777,216 x 1 bit structure 256 Equal Sectors with 8K-byte each o Any sector can be erased ...
Page 47
SI Input o Serial Data Input SO Output o Serial Data Output PACKAGE o 28-pin SOP (330mil) General Description The MX25L1602 is a CMOS 16,777,216 bit serial Flash EEPROM, which is configured as 2,097,152 x 8 internally. The MX25L1602 features a serial peripheral interface and software protocol allowing operation on a simple 3- wire bus.
Page 48
Table: Pin description M25Q32FV SPI FLASH Key Features New Family of SpiFlash Memories o W25Q32FV: 32M-bit/ 4M-byte o Standard SPI: CLK, /CS, DI, DO, /WP, /Hold o Dual SPI:CLK, /CS, IO , IO , /WP, /Hold o Quad SPI: CLK, /CS, IO , IO , IO , IO...
Page 49
o Erase/Program Suspend&Resume Advanced Security Features o Software and Hardware Write-Protect o Power Supply Lock-Down and OTP protection o Top/Bottom, Complement array protection o Individual Block/Sector array protection o 64-Bit Unique ID for each device o Discoverable Parameters (SFDP) Register o 3x256-Bytes Security Registers with OTP locks o Volatile &...
Recommended Operating Conditions 12. LNB SUPPLY AND CONTROL IC LNBH29 General Description LNBH29 IC is intended for analog and digital Satellite receivers/Sat-TV, Sat-PC cards, the LNBH29 series is a monolithic voltage regulator and interface IC, assembled in QFN3x3-16L and QFN4x4-16L, specifically designed to provide the 13/18V power supply and the 22KHz tone signaling to the LNB down-converter in the antenna dish or to the multi-switch box.
13. TROUBLESHOOTING A. NO BACKLIGHT PROBLEM Problem: If TV is working, led is normal and there is no picture and backlight on the panel. Possible couses: Backlight pin, dimming pin, backlight supply, stby on/off pin BACKLIGHT_ON/OFF pin should be high when the backlight is ON. R23 must be low when the backlight is OFF.
Page 56
Dimming pin should be high or square wave in open position. If it is low, please check S268 for Mstar side and panel or power cables, connectors. Backlight power supply should be in panel specs. Please check Q34, shown below; also it can be checked TP149.
STBY_ON/OFF_NOT should be low for tv on condition, please check Q39’s collector. D. CI MODULE PROBLEM Problem: CI is not working when CI module inserted. Possible couses: Supply, suply control pin, detect pins, mechanical positions of pins. CI supply should be 5V when CI module inserted. If it is not 5V please check CI_PWR_CTRL, this pin should be low.
Page 58
Please check mechanical position of CI module. Is it inserted properly or not? Detect ports should be low. If it is not low please check CI connector pins, CI module pins.
E. STAYING IN STAND-BY MODE Problem: Staying in stand-by mode, no other operation This problem indicates a short on Vcc voltages. Protect pin should be logic high while normal operation. When there is a short circuit protect pin will be logic low. If you detect logic low on protect pin, unplug the TV set and control voltage points with a multimeter to find the shorted voltage to ground.
G. KEYPAD TOUCHPAD PROBLEMS Problem: Keypad or Touchpad is not working Check keypad supply on MB100. H. USB PROBLEMS Problem: USB is not working or no USB Detection. Check USB Supply, It should be nearly 5V. Also USB Enable should be logic high.
For USB 3.0 ports: For USB 2.0 port: İ. NO SOUND PROBLEM Problem: No audio at main TV speaker outputs. Check supply voltages of 24V VDD_AUDIO, 3.3V AUDIO_AVDD and AUDIO_DVDD with a voltage- meter. There may be a problem in headphone connector or headphone detect circuit (when headphone is connected, speakers are automatically muted).
J. STANDBY ON/OFF PROBLEM Problem: Device can not boot, TV hangs in standby mode. There may be a problem about power supply. Check main supplies with a voltage-meter. Also there may be a problem about SW. Try to update TV with latest SW. Additionally it is good to check SW printouts via Teraterm.
Page 64
14. GENERAL BLOCK DIAGRAM Shutter (Active) Polarizer (Passive) Glasses Glasses 2x8W or 2x10W 5V_VCC 5V_VCC 5V_VCC (64Mx16bit or 128Mx16bit) TPS2553 TPS2553 TPS2553 Subwoofer (1600 MT/s) Bathroom USB Power USB Power USB Power Supply Switch Supply Switch Supply Switch Amp. TAS5727 (USB1) (USB2) (USB3)