Table of Contents
SIMATIC Field PG M4
SIMATIC
Programming device
SIMATIC Field PG M4
Getting Started
10/2012
A5E31347325-AA
___________________
Introduction
___________________
Description
___________________
Application planning
___________________
Installing and connecting
___________________
Commissioning
___________________
Appendix
1
2
3
4
5
A
Table of Contents
Related Manuals for Siemens SIMATIC Field PG M4
Summary of Contents for Siemens SIMATIC Field PG M4
- Page 1 ___________________ SIMATIC Field PG M4 Introduction ___________________ Description ___________________ Application planning SIMATIC ___________________ Installing and connecting Programming device ___________________ SIMATIC Field PG M4 Commissioning ___________________ Appendix Getting Started 10/2012 A5E31347325-AA...
- Page 2 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 3: Table Of Contents
Connecting peripherals ........................14 Connecting the device to power....................15 Commissioning ............................17 Requirements for commissioning....................17 Initial commissioning - initial startup ....................17 Appendix..............................20 Guidelines and declarations......................20 Certificates and approvals ......................21 Service and support ........................22 SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... -
Page 4: Introduction
The warnings are highlighted by a warning triangle and presented in different forms based on the degree of hazard. Conventions The terms "PG" or "device" are also used to refer to the SIMATIC Field PG M4 product in this documentation. SIMATIC Field PG M4... -
Page 5: Description
Description Exterior design View with closed display ① System and keyboard LEDs ② Display latch ③ Device handle SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... - Page 6 View from rear ① DisplayPort ② 2 x Ethernet ③ 2 x USB 3.0 ④ MPI/DP ⑤ DVI-I ⑥ RS232/TTY (TTY functionality, depending on the HW configuration variant) ⑦ Ventilation air outlet SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA...
- Page 7 Optical drive ② SIMATIC Micro Memory Card interface ③ Exchangeable hard disk unit ④ Memory card interface ⑤ 2 x USB port, with cover Top port: USB 2.0 Bottom port: USB charger SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA...
-
Page 8: Operator Controls
Switch PG on/off (hold the button down for approximately 1 second; the response depends on the Windows power options settings) Switch PG off in the event of a fault (hold down for more than 5 seconds) SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... - Page 9 Press the on/off button briefly to reactivate the PG from Standby mode or Hibernation. In Standby mode the device LED flashes, and in Hibernation all the displays are switched off. SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA...
-
Page 10: Touchpad
"noisy" environment. In such environments, it is a good idea to disable the tap function in the touchpad driver, and to use the mouse buttons. SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... -
Page 11: Application Planning
Ethernet address 1 Ethernet address 2 Enter the following data in the table: ● Serial number The serial number (S VP) is located on the rating plate on the bottom of the device. SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... - Page 12 ● Microsoft Windows "Product Key" on the "Certificate of Authenticity" (COA). The Product Key is always required to reinstall the operating system. COA label The COA label is stuck to the bottom on the device. SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA...
-
Page 13: Installing And Connecting
● Open the display by sliding the latch in the direction of the arrow. ● Flip the display open and adjust it to a convenient viewing angle. The display can be adjusted to any inclination angle between 0 and 150 SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... -
Page 14: Connecting Peripherals
You can connect headphones or external speakers that are equipped with a 3.5 mm stereo jack plug to the headphones jack (green). You can control the volume using the speaker button on the taskbar, or using hotkey Fn + F7 / F8. SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... -
Page 15: Connecting The Device To Power
15 A/250 V connector. The cable set must conform to the safety regulations of the country in which the devices are installed, and bear the prescribed markings in each case. SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... - Page 16 Insert the low-voltage connector ① into the connection on the device. Plug the external power supply into a socket with a grounded protective conductor. Turn the PG over again. SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA...
-
Page 17: Commissioning
2. Wait until this message is cleared, then follow the instructions on the screen. 3. Type in the Product Key as required. You find this key on the "Certificate of Authentication", in the "Product Key" line. 4. Automatic restart SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... - Page 18 2. You can make your changes in the "Administrative" tab. Click the respective button to copy the settings. For more information, refer to chapter "Setting up the language selection by means of Multilingual User Interface (MUI) (http://support.automation.siemens.com/WW/view/en/10805333/133300)". SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA...
- Page 19 Transferring the SIMATIC STEP 5 authorization Run "install.exe" from the License Key in the USB_Stick:>\UCL directory to transfer the STEP 5 authorization. Follow the instructions on the screen to transfer the authorization. SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA...
-
Page 20: Appendix
Declaration of conformity The EC declaration of conformity and the corresponding documentation are made available to authorities in accordance with the EC directives stated above. Your sales representative can provide these on request. SIMATIC Field PG M4 Getting Started, 10/2012, A5E31347325-AA... -
Page 21: Certificates And Approvals
Certificates and approvals DIN ISO 9001 certificate The Siemens quality management system for all production processes (development, production, and sales) meets DIN ISO 9001:2000 requirements. This has been certified by DQS (the German society for the certification of quality management systems). -
Page 22: Service And Support
You can find additional information and support for the products described on the Internet at the following addresses: ● Technical support (http://www.siemens.com/automation/service&support) ● Support request form (http://www.siemens.com/automation/support-request) ● After-sales information system for SIMATIC PC / PG (http://www.siemens.com/asis) ● SIMATIC Documentation Collection (http://www.siemens.com/simatic-tech-doku-portal) ● Your local representative (http://www.siemens.com/automation/partner) ● Training center (http://www.sitrain.com) ●...