Related Manuals for Siemens FC901-U3
Summary of Contents for Siemens FC901-U3
- Page 1 Fire Alarm Control Panel Model FC901-U3/FC901-R3 Installation, Operation and Maintenance Manual Siemens Industry Inc.
-
Page 4: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ............................1 CONTROL PANEL LIMITATIONS ........................1 PREFACE ..............................2 FCC Part 68 WArning ............................ 2 DESCRIPTIONS ............................. 4 FC901 SYSTEM DESCRIPTION........................4 Power Supply ............................... 4 Signaling Line Circuit (SLC) .......................... 5 Notification Appliance Circuits ........................5 Serial Interface Circuit ........................... - Page 5 Supervisory Conditions ..........................16 ADDITIONAL OPERATING PROCEDURES ....................18 Lamp Test ..............................18 History ................................ 18 FC901 OPERATING INSTRUCTIONS ......................19 Alarm Operation ............................19 Authorized Personnel Only.......................... 19 Trouble Operation ............................19 Event Scrolling ............................19 Fuse Replacement and Battery Maintenance ....................19 FSD901 OPERATING INSTRUCTIONS......................
- Page 6 SLC Current Draw Break down ........................50 Battery Size ..............................51 APPENDIX-B: COMPATIBLE DEVICES ...................... 52 DEVICES FOR ADDRESSABLE DEVICE CIRCUITS ................. 52 Siemens SLC Manual Pull Stations ......................52 Siemens SLC Modules..........................52 Siemens SLC Bases ........................... 52 Siemens SLC Accessories .......................... 52 8700 SLC Manual Pull Stations ........................
-
Page 8: Introduction
INTRODUCTION CONTROL PANEL LIMITATIONS This control panel may not show an alarm condition without compatible initiating devices (smoke detectors, etc.) and notification devices (horn, strobes, etc.) connected to it. Electrical ratings of the initiation and notification appliances must be compatible with the electrical ratings of the control panel and must be properly interconnected. -
Page 9: Preface
PREFACE Along with the use of this instruction manual, the appropriate following standards and the manufacturer's instructions for initiating and notification devices should be used to install and maintain a functioning fire alarm signaling system. NFPA 72 National Fire Alarm Code For other standards that may apply contact the authority having jurisdiction. - Page 10 It is the responsibility of users requiring service to report the need for service to our Company or to one of our authorized agents. Service can be facilitated through our office at: SIEMENS INDUSTRY, INC. – BUILDING TECHNOLOGIES DIVISION – FIRE SAFETY 8 FERNWOOD RD., FLORHAM PARK, NJ 07932 -800-248-7976...
-
Page 11: Descriptions
DESCRIPTIONS FC901 SYSTEM DESCRIPTION The FC901 is a compact but powerful standalone fire alarm control panel. It features advanced addressable fire detection, keypad and offline programming, notification circuits, a 160 by 64 dots LCD display and event history retention capability. It’s typical configuration includes a power supply, a signaling addressable device circuit, two notification appliance circuits (NAC), Digital Alarm Communication Transmitter (DACT), four system status relays and a USB programming port. -
Page 12: Signaling Line Circuit (Slc)
There is also a system coder capable of zone operation. All of the NACs are power limited and support synchronization of listed devices using the Siemens sync protocol. Serial Interface Circuit (UFP) The FC901 control panel has a Serial Interface Circuit (UFP) that will drive up to 8 devices, eg. -
Page 13: Auxiliary Modules
Note: For printer connection, wiring between the RPM and printer must be in conduit within 6 feet and in the same room as the panel. AUXILIARY MODULES Serial LCD Annunciators The FSD901 Serial LCD Annunciator consists of a backlit 160 by 64 dot (7 by 26 characters) LCD display, acknowledge, silence, unsilence, and reset buttons, a four-way button for event navigation, seven system status LED indicators and a security key switch. -
Page 14: Slc Addressable Devices
SLC ADDRESSABLE DEVICES Smoke Detector The control panel processor sends the sensitivity settings to the detectors and polls the detectors for their status. The detector determines normal, trouble and alarm conditions and communicates the conditions to the control panel. Variable Thresholds - The detectors can be set to operate in various pre-programmed profiles, depending on the environment where the detectors are used. -
Page 15: Programming Slc Devices
the system configuration tool. When users need to disable the audible base , they will need to select the “disable audible base” option. When the audible base ABHW-4B and ABHW-4S is used with H/8700 series detectors, it can be programmed to 1 output channel, and only 2 tone patterns (steady, temporal 3) can be selected using the system configuration tool. -
Page 16: Event History
EVENT HISTORY The control panel includes a non-volatile memory recording 1000 system events. Identified alarm, trouble, supervisory, status and other significant events will be recorded along with the date and time of occurrence. The history event log can be viewed at the main system display by operating menu controls from the panel. -
Page 17: General Design Features
GENERAL DESIGN FEATURES Environmental The FC901 panels and subassemblies are suitable for use in a dry, indoor or protected location. Power Limiting The AC power connection, battery wiring and four system status relays are not power limited. All other circuits leaving the control panel meet the requirements for power limited circuits when installed in accordance with the National Electrical Code and local requirements. -
Page 18: Regulatory Standards
Configured device is missing. Unconfigured device is installed. Two devices are programmed with the same address. Signaling line circuit experiences a wire-to-wire short. Signaling line circuit experiences an earth ground condition. REGULATORY STANDARDS The FC901 control panel meets the requirements of industry and government regulatory agencies as noted. -
Page 19: General Specifications
GENERAL SPECIFICATIONS Operating specifications for the FC901 are as follows: Environmental Operating temperature - 32 - 120°F (0 - 49°C) Relative humidity - Up to 93% @ 90°F (32°C) To be installed in a indoor dry protected environment only Primary Power Supply Input: 120VAC, 60Hz or 240VAC, 50Hz @ 2.0A Max. -
Page 20: Status Relays
Status Relays Non-power limited One programmable relay Three non-programmable relays: Trouble, Supervisory, Alarm Contact rating: 2A, 30VDC maximum Form C contact Notification Appliance Circuits Power limited Supervised Current Draw Maximum Line Resistance 2.5A 3.2Ω 2.0A 4.0Ω 1.5A 5.3Ω 1.0A 8.0Ω 0.5A 16.0Ω... -
Page 21: Dact Circuits
18 – 28VDC for battery Current: Max. 0.4A Supervised Output: City Tie-Output 1 Normal output voltage: 19-28VDC (open circuit condition) Supervisory current: Maximum trip current: 400mA 22.5Ω Maximum coil plus wire resistance: Leased line-Output 1 Normal output voltage: 19-28VDC (open circuit condition) Trouble output voltage: Alarm output voltage: -(19-28)VDC (open circuit condition) -
Page 22: Control Panel Operation
CONTROL PANEL OPERATION OPERATION INSTRUCTIONS Standby Condition In normal standby operation, the green AC POWER ON LED should be illuminated and no other indicator operating. The display will show the system label and the current time. Alarm Conditions ALARM When the system detects an alarm condition, the alarm LED activates (ON – flashing) and the local panel buzzer activates in a specific pattern to indicate an alarm condition. -
Page 23: Trouble Conditions
PRE-SIGNAL ALARMS Activation of an initiating device in an input group programmed for PRE-SIGNAL, activates the Alarm LED, LCD display, and the local panel buzzer. System and user-programmed outputs activate immediately except NAC. The delay of activation of user-programmed outputs can be programmed from 60 to 180 seconds. - Page 24 If the FC901 is configured as “Supervisory self restoring”, the system shall return to the “System Normal” status if the supervisory condition is restored unless there are additional events on the system. If the FC901 is not configured as “Supervisory self restoring”, the system reverts to standby condition only after the RESET button is pressed.
-
Page 25: Additional Operating Procedures
ADDITIONAL OPERATING PROCEDURES In addition to the basic fire alarm instructions above, several features are included to facilitate maintenance and increase the versatility of the system. The following are procedures used to initiate these functions. Lamp Test When selected, Lamp Test activates LCD, the buzzer and turns on all the LEDs on the user interface, then back to its previous state. -
Page 26: Fc901 Operating Instructions
FC901 OPERATING INSTRUCTIONS Alarm Operation In case of alarm, the Alarm LED flashes, LCD displays alarm conditions and the panel buzzer sounds in a distinct alarm pattern. Local audible and visual signals and remote alarm signals operate. When an alarm occurs, proceed according to the established emergency plan. Assure that all personnel are accounted for, and notify the Fire Department to advise of the alarm and/or verify that an automatic signal has been received at the Fire Department. -
Page 27: Fsd901 Operating Instructions
FSD901 OPERATING INSTRUCTIONS Alarm Operation In case of alarm, the Alarm LED flashes, LCD displays alarm condition and the buzzer sounds. Local audible and visual signals and remote alarm signals operate. When an alarm occurs, proceed according to the established emergency plan. Assure that all personnel are accounted for, and notify the Fire Department to advise of the alarm and/or verify that an automatic signal has been received at the Fire Department. -
Page 28: Control Panel Installation
CONTROL PANEL INSTALLATION PARTS SUPPLIED – FC901 FC901 Enclosure Assembly FH901-U3(Black)/FH902-U3(Red) FC901 Main Board Assembly FCM901-U3 Power Supply Assembly FP2011-U1 FC901 City Tie Module Assembly (optional) FCI2020-U1 FC901 Configuration Kit (optional) FXS901-U3 1. FC901 Enclosure Package FC901 black enclosure Description Part No. -
Page 29: Fc901 Configuration Kit Package
FC901 main board installation A5Q00039713 instruction FC901 operation and N/A in BSCE programming instruction FC901 wiring diagram A5Q00039694 #8-32 x 3/8” screws A5Q00043106 #4-40 x 1/4” screws A5Q00043105 Grounding cable A5Q00044075 3. FC901 Configuration Kit Package Description Part No. FC901 Configuration A5Q00039718 programming disk FC901 Commissioning cable... -
Page 30: Cautions
CAUTIONS 1. Remove the printed circuit boards for any procedure that may cause dust, metal shavings, grease (or such matter that may affect the operation of the boards) to get in contact with the units. 2. Disconnect all sources of power prior to installing or removing modules, connecting or disconnecting wiring. - Page 31 There are two key-shaped cutouts on the top of the backbox. Make sure the end with the two key-shaped cutouts is on top when installing the backbox. The front door can be removed from the enclosure for more convenient installation. 2.
- Page 32 FC901 Enclosure Mounting Pictures...
-
Page 33: Remove Knock-Outs
FC901 Installation Size 6-2 3/8” 1 61/64” 1 3/16” 1 1/32” 16” 1 7/16” Remove Knock-Outs Prepare the enclosure for electrical wiring by breaking out the appropriate conduit entry points. Segregation is required between power limited and non-power limited conductors. In order to maintain the minimum separation, follow the wire routing illustrated on page 31. -
Page 34: Power Supply Mounting
Power Supply Mounting Secure the power supply to the back of enclosure using the four provided #8-32 x 3/8 screws. AC Input terminals must be located at the right side of the enclosure. -
Page 35: Ground Wire Installation
Ground Wire Installation Install one end of the grounding cable on the enclosure back box. Enclosure back box Install the other end of the grounding cable on the enclosure outer door. Enclosure outer door... -
Page 36: Battery Installation
Battery Installation Use the battery calculation chart to determine the battery size. Place the batteries in the space provided in the bottom of the backbox. Secure the battery bracket (if required) to the back of enclosure using the eight provided #8-32 x 3/8 screws. Recommended battery size : Length:5.94 inch, Width: 3.86 inch, Height:3.7 inch. -
Page 37: Optional City Tie Mounting
Optional City Tie Mounting Secure the city tie to the main board using the two provided #4-32 x 3/8 screws. Spacer Detail A 2 #4 screws City tie module Connect the city tie cable between city module and main board. From 1 to 4 TP1295,TP1294,TP1293,TP1292 From left to right:... -
Page 38: Main Board Assembly Installation
Main Board Assembly Installation Secure the main board assembly to the enclosure using the four provided #8-32 x 3/8 screws 4 #8 screws Earth Cable Installation Connect the earth cable to the backbox and connector at the upper left corner of the main board. -
Page 39: System Wiring
SYSTEM WIRING Before connecting the field wiring, check the wiring for opens, shorts, grounds and stray voltages. WARNING Damage may result if a high voltage insulation tester is used on wiring while connected to the control panel. Terminate the field wiring to the main board in accordance with the diagrams in System Wiring Section. -
Page 40: Control Panel Wiring Overview
Control Panel Wiring Overview In compliance with NEC Article 760 and UL 864, all power limited fire protective signaling conductors must be separated a minimum of 1/4 inch from all of the following wiring located within a control panel: Electric light Power Class 1 or non-power limited fire protective signaling conductors To meet these requirements, the following guidelines must be observed when installing... -
Page 41: Wiring Separation
Wiring Separation All high voltage and non-power limited wiring must be kept separate from power limited wiring. A separation of at least 1/4 inch must be maintained with high voltage and non-power limited wiring running in separate conduit openings from power limited wiring. 7 Optional field wire knock-outs Relay-1 Dialer... -
Page 42: Internal Structure
Internal Structure Enclosure Main board assembly Power supply Battery bracket right Batteries Battery bracket left... -
Page 43: Power Supply And Battery Wiring
Power Supply and Battery Wiring Route all high voltage and non-power limited wiring together and away from power limited wiring. Use the battery calculation chart to determine battery size. AC connection is done on power supply. Non-Power Limited Earth GND Brownout Connect to Main board Neutral... -
Page 44: Status Relays
P2 device Auxiliary power Series Interface City tie and DACT Status Relays circuit output Circuit lease line Power limited Non power limited Wiring terminals located on top of main board Status Relays Four relays with dry contacts are provided at the upper right corner of the main board. One relay is programmable and the trouble relay, supervisory relay and alarm relay are non- programmable. -
Page 45: Nac Wiring
NAC Wiring Two individual NACs are provided and the polarity shown is when the NAC is activated. Power Limited Supervised Current Draw Maximum Line Resistance 2.5A 3.2Ω 2.0A 4.0Ω 1.5A 5.3Ω 1.0A 8.0Ω 0.5A 16.0Ω Alarm voltage: 16 to 32VDC Maximum ripple: 0.1VAC Used for special application only Two Style Y/Class B or one Style Z/Class A... -
Page 46: Serial Interface Circuit
Serial Interface Circuit (UFP) The serial interface circuit can address up to 8 devices, which include annunciators and printer modules. Up to 2 printers can be addressed. Devices on the circuit may be connected up to 4000 feet from the control panel. Serial Interface Circuit (UFP) (PR_A, PR_B) RS-485 levels Wire Type-Twisted Pair For Data... -
Page 47: Serial Remote Device Wiring Overview
Serial Remote Device Wiring Overview When connecting devices on the Serial Interface Circuit (UFP), the data wires must be daisy chained and with no T-taps to preserve the integrity of the data. The following diagrams show the proper wiring. Class B Style 4 Annunciator Annunciator PR_A/B... -
Page 48: Slc Addressable Device Circuit
SLC Addressable Device Circuit These devices are polled by the control panel every few seconds and input or output functions communicated to determine device status or function. The control panel monitors all device addresses for alarm and trouble conditions. Addressable Device Circuit Style 4 (Class B) or Style 6 (Class A) Operation Max. -
Page 49: Slc Addressable Device Wiring Diagrams
AS PORT-A NOTE: Siemens SLC Devices: Detectors, Monitor Modules, or Control Modules up to a maximum of 50 devices (include both PORT-A and PORT-B). A Maximum of 20 devices recommended per Isolator Module. A Maximum of 15 Isolator Modules per addressable device circuit. - Page 50 MODULE NOTE NOTE: Siemens SLC Devices: Detectors, Monitor Modules, or Control Modules up to a maximum of 50 devices. A Maximum of 20 devices recommended between Isolator Modules. A Maximum of 15 Isolator Modules per addressable device circuit. NOTE: If more than one HCP is used on a SLC device loop, the loop must be wired Class A or the riser conductors must be installed in accordance with the Survivability From Attack By Fire requirements in the National Fire Alarm Code, NFPA 72.
-
Page 51: Optional City Tie/Leased Line
Optional City Tie/Leased Line FC901 provides one city tie or two leased lines to connect with local energy and polarity reversal. City tie and Leased line Supervised, Power Limited City tie CT_P Master Box CT_N LL_SP LL_SN Leased line leased line CT_P alarm/trouble detection circuit... -
Page 52: Programming The Control Panel
This is the recommended method to program the panel. The Siemens FXS901-U3 software is available to allow programming the control panel by connection to a Personal Computer (PC) with an USB port. This allows ease of operation by preparing the program in advance and downloading to the control panel in a simple, rapid operation. -
Page 53: Maintenance
MAINTENANCE GENERAL The FC901 provides maintenance functions to allow for the setting and controlling of various features in the system. The maintenance functions are protected by a four digit password. To access the maintenance features press the “MENU” button and select Login item in the View menu, enter the four digit code when prompted and then press “OK”. -
Page 54: Quick Test
QUICK TEST The Quick Test mode makes it fast and easy to test a system by eliminating the need to disconnect panel from remote connections to the Fire Department or other monitoring stations. In this way, operator can test all devices locally without annunciating any condition to remote connections. - Page 55 This page is left intentionally blank.
-
Page 56: Appendix-A: Reference Data
Total loop resistance - 50 ohm maximum with 50 devices Total loop capacitance - 0.5uF max line to line per km and 1.0uF max line to shield per km The terminal blocks of Siemens SLC devices are rated for a maximum of 14AWG wire. -
Page 57: Battery Size Calculations
BATTERY SIZE CALCULATIONS System Current Draw Break down System Current Draw Components Standby(A) Alarm(A) Main board 0.1590 0.1864 Auxiliary power City tie module 0.0017 0.0158 SLC Current Draw Break down SLC Current Draw Components Standby(A) Alarm(A) HFP-11 / 8713 0.00140 0.00140 HFPO-11 / 8710 0.00140... -
Page 58: Battery Size
Battery Size Total Standby Hours of Standby AH for Current Required per NFPA 72 Standby (from above) Standard (4, 24 or 90) Hours Total Alarm 5 Minutes of Alarm AH for Alarm Current Operation (from above) per NFPA 72 Standard Hours A.H. -
Page 59: Appendix-B: Compatible Devices
APPENDIX-B: COMPATIBLE DEVICES DEVICES FOR ADDRESSABLE DEVICE CIRCUITS Siemens SLC Manual Pull Stations Siemens Description Cat. No. HMS-S Manual Station, Single Action HMS-D Manual Station, Double Action HMS-M Metal Manual Station, Single Action HMS-2S single action manual pull station with 2-stage key switch... -
Page 60: 8700 Slc Manual Pull Stations
Air Duct Housing Notes: Siemens SLC devices, detectors and modules, up to a maximum of 50 addresses may be used. For specific wiring and installation information, read the instructions provided with each device. If more than one HCP is used on a SLC device loop, the loop must be wired Class A or the riser conductors must be installed in accordance with the Survivability From Attack By Fire requirements in the National Fire Alarm Code, NFPA 72. -
Page 61: Global Asa
FC901 support OOHC941 CO function. CO channel can be configured as automatic alarm event and supervisory event in the detection tree of FC901. But it does not comply with UL 2017 standard when CO channel was configured to automatic alarm event. It does comply with UL 864. UFP devices Siemens Description Cat. No. FT2007-U1... -
Page 62: Appendix-C: Troubleshooting
APPENDIX-C: TROUBLESHOOTING DEFINITIONS FOR EVENT HISTORY ENTRIES A. General ENTRY INDICATES Disabled The device has been disabled Ground The device is in ground fault Open The device is in open trouble Short The device is in short trouble Overload The SLC line is overloaded GeneralTrouble The device reports general trouble Unconfig... -
Page 63: Appendix-D: Alarm Verification
APPENDIX-D: ALARM VERIFICATION A - Smoke detector goes into alarm. (LED on device turns to red) AB - Retard Period, FACP senses detector in alarm and delays alarm signal for 50s. In this period, no alarm event reports on FACP. BC - Confirmation Period, Detector is operational for alarm at point B. -
Page 64: Appendix-E: Application Specific Detection
APPENDIX-E: APPLICATION SPECIFIC DETECTION Application Specific Detection (ASD) allows the system designer to program a detector’s sensitivity, pre-alarm threshold, and other alarm-related parameters using English descriptions of the detector's environment (application). This eliminates the need for detailed knowledge of smoke detector terminology and operation. The designer can set all of the critical detector parameters by simply selecting an application description that closely fits the one where the detector is to be installed. -
Page 65: Appendix-F: Testing/Maintenance
APPENDIX-F: TESTING/MAINTENANCE If the system is connected to the fire department, etc., or actuates an internal system, disarm the appropriate outputs before servicing to prevent actuation. Notify the fire department and personnel at your facility that a System test is being performed so that any alarm sounding can be ignored during the test. -
Page 66: Appendix-G: Lcd, Controls And Indicators
APPENDIX-G: LCD, CONTROLS AND INDICATORS The FC901 has a buzzer, 7 LEDs, 4 navigational push buttons, 4 dedicated push buttons, alphanumeric keypad, 3 menu control buttons (menu, cancel, ok) and a communication port connector. Communication Port Connector The communication port is connected to the USB port of the computer that has the FXS901-U3 programming tool. - Page 67 This indicates that there is no supervisory event in system. This indicates that there are supervisory events Flashing in system, but some of them have not been acknowledged. This indicates that there are Ground Fault Steady ON events in system. This indicates that there is no Ground Fault Ground Fault Yellow...
- Page 68 The buttons operates as follows: Silences all silenceable devices in system. This will cause all activated Alarm Silence Press silenceable devices to become silenced. Acknowledge Press Acknowledges all unacknowledged events in system. Clears all obsolete events and resets all devices, except those disabled ones Reset Press and hold-through-reset devices in system.
-
Page 69: Lcd Display
LCD Display The LCD operates as follows: Trouble 02/13 12:12 V AutoAlarm Zone 1 10-30-2010 12:00:01 V Open Line 1 10-30-2010 12:00:00 Line 1 – Index and Category of current selected event, User level, current time Line 2 – Acknowledged status, Event Type Line 3 –... -
Page 70: Appendix-H: Output Features
APPENDIX-H: OUTPUT FEATURES Output Activation- and Deactivation- Delays Each output device has a selection for Activation delay and Deactivation delay when it is installed in the configuration. The Activation delay refers to the delay in which the output will activate after the reception of its activation command. If the Activation delay is set to 0 (default setting), the output immediately activates. -
Page 71: Appendix-I: Pas / Pre-Signal
APPENDIX-I: PAS / PRE-SIGNAL PAS (Positive Alarm Sequence) and Pre-Signal features allow the user to delay the activation of the audibles, strobes and other output devices when an initial alarm is detected. Output can be interlocked by zones. When an initial alarm is detected, all outputs except remote devices (off-premises devices like general relays and city tie) associated with PAS Zone (Zone configured with PAS feature) will be activated immediately. -
Page 72: Pre-Signal
Pre-Signal When an alarm causing device in a Pre-Signal input group is initiated, the alarm condition is reported at the panel. Its associated NACs are not activated until the programmed investigation delay has relapsed or 2 Alarm is initiated anytime during the Pre-Signal delay time (see figure below). -
Page 73: Appendix-J: Dact Information Overview
APPENDIX-J: DACT INFORMATION OVERVIEW The DACT (Digital Alarm Communicator Transmitter) is an optional module for the FC901 control panel that allows transmission of event information to a remote receiver at a monitoring station using a dial-up modem connection. These events are transmitted in one of the following formats: ... - Page 74 To configure an event to be reported to Account 1 and Account 2, set it to Must report on both. If the event needs to be reported to either Account 1 or Account 2, set it to Can report on both. If it has to be reported to Account 1, but only needs to be reported on Account 2 if Account 1 is temporarily out-of-order, set the event to Must Report on Account 1 and Can Report on Account 2.
- Page 75 Scenario 2 – Must/Can Alarm Event is set to Must Report on Account 1 and Can Report on Account 2. Panel fails on Account 1 the first time. Step 1: Panel goes into alarm. Account 1 Step 2: Panel tries to send event to Account 1, but is unsuccessful.
- Page 76 Scenario 3 – Must/Can Alarm Event is set to Must Report on Account 1 and Can Report on Account 2. Panel succeeds on Account 1 the first time. Step 1: Panel goes into alarm. Account 1 Step 2: Panel tries to send event to Account 1 successful.
- Page 77 Scenario 4 – Can/Can Alarm Event is set to Can Report on Account 1 and Account 2. Panel succeeds on Account 2 before Account Step 1: Panel goes into alarm. Account 1 Step 2: Panel tries to send event to Account 1, but is unsuccessful.
- Page 78 DACT Compatible Alarm Communicators The FC901-U3/-R3 DACT is also compatible with Alarm communicators that utilized different communication technologies (IP and GSM technologies) to connect to compatible Receivers using compatible protocol listed within this documentation. COMPATIBLE ALARM COMMUNICATORS Installation Manufacturer Model...
-
Page 79: Appendix-K: Drift Compensation
APPENDIX-K: DRIFT COMPENSATION The H-Series/8700 optical detector cannot implement drift compensation on its own. Drift compensation is the panel’s responsibility. While the system is running, the detector sends its chamber real-time values to the panel periodically and does not do compensation by itself. For the first hour after a panel startup, the panel will check the detector chamber values every 10 minutes. -
Page 80: Appendix-L: Glossary
APPENDIX-L: GLOSSARY AC Power Fail. Refers to a condition in which AC power loss is detected by the system. Alarm Signal. A signal indicating an emergency requiring immediate action, such as an alarm for fire from a manual station, a waterflow alarm, or an automatic smoke detector. Alarm Silence Inhibit. - Page 81 fan restart usage has higher priority than the OFF time delay and will therefore immediately deactivate the hold-thru reset outputs. Initiating Device. A manually or automatically operated device such as a manual pull station, smoke detector, heat detector, waterflow switch or tamper switch. Initiating Device Circuit (IDC).
- Page 82 Waterflow Switch. An assembly approved for service and so constructed and installed that any flow of water from a sprinkler system equal to or greater than that from a single automatic sprinkler head will result in activation of this switch and subsequent indication of an alarm condition.
- Page 83 © 2016 Copyright by Beijing Siemens Cerberus Electronics Limited No.1,Fengzhidonglu, Xibeiwang, HaiDian District, Beijing Siemens Cerberus Electronics Ltd. Beijing, 100094, China Data and design subject to change without notice. Tel: +10 6476 8806 Fax: +10 6476 8899 Document no. A6V10336754_i_en_--...